Nortel NT1R20 Description page 202

Page 178 of 290
Figure 42
Set Mode (S M): Table screen (Part Two)
O u t g o i n g c a l l S E I Z E R E C E I V E :
E r r o r : N o t e e n o u g h v a l u e s s p e c i f i e d .
v a l u e s .
O u t g o i n g c a l l S E I Z E R E C E I V E :
O u t g o i n g c a l l S E I Z E R E C E I V E b i t s c h a n g e d t o : 1 1 1 1
O u t g o i n g c a l l S E I Z E A C K S E N D e n a b l e d ? ( Y / N ) : N
O u t g o i n g c a l l S E I Z E A C K S E N D i s d i s a b l e d .
O u t g o i n g c a l l D I A L M A K E R E C E I V E :
O u t g o i n g c a l l D I A L M A K E R E C E I V E b i t s n o t c h a n g e d .
O u t g o i n g c a l l D I A L B R E A K R E C E I V E :
O u t g o i n g c a l l D I A L B R E A K R E C E I V E b i t s n o t c h a n g e d .
O u t g o i n g c a l l A N S W E R E D S E N D :
O u t g o i n g c a l l A N S W E R E D S E N D b i t s n o t c h a n g e d .
O u t g o i n g c a l l ( C P E ) D I S C O N N E C T R E C E I V E :
O u t g o i n g c a l l ( C P E ) D I S C O N N E C T R E C E I V E b i t s n o t c h a n g e d .
O u t g o i n g c a l l ( F a r E n d ) D I S C O N N E C T S E N D :
O u t g o i n g c a l l ( F a r E n d ) D I S C O N N E C T S E N D b i t s n o t c h a n g e d .
D i s c o n n e c t T i m e ( 0 t o 4 0 0 0 m s ) : 1 0 0 0
D i s c o n n e c t T i m e n o t c h a n g e d .
I n t e r c a l l T i m e ( 0 t o 2 0 0 0 m s ) : 8 0 0
I n t e r c a l l T i m e n o t c h a n g e d .
L E I : >
553-3001-105 Standard 5.00 June 1999
NT5D33 and NTRB34 Line-side E1 Interface Cards
Idle SEND - This is the value that the LEI will send (acting as the CO or
PSTN) when the circuit is in the idle state. This value is required.
Idle RECEIVE - This is the value that the LEI expects to see from the CPE
when it is in the idle state. This value is required.
Blocking RECEIVE - This is the value that the LEI expects to see from the
CPE when the customer equipment is in the blocking or fault state and is
unable to accept new calls. This value can be set to N if this state is not
needed. If this value is not set to N, then dip switch #2 position 6 will
determine whether off-hook or on-hook is sent to the M1/SL100 when this
state is entered. See Table 38 on page 150.
C u r r e n t : 0 0 0 1
E n t e r e i t h e r 2 o r 4
C u r r e n t : 0 0 0 1
C u r r e n t : 1 1 1 1
C u r r e n t : 1 0 1 0
C u r r e n t : 0 1 0 1
C u r r e n t : 0 1 0 1
C u r r e n t : 1 1 1 1
N e w : 1 1 1
N e w : 1 1
N e w :
N e w :
N e w :
N e w :
N e w :