Ventrac HQ680 Original Operator's Manual
Tough cut mower
Hide thumbs
Also See for HQ680:
- Owner's/operator's manual (30 pages) ,
- Owner's and operator's manual (33 pages)
Related Manuals for Ventrac HQ680
Summary of Contents for Ventrac HQ680
- Page 1 Operator’s Manual HQ680 Tough Cut Mower Europe - Serial Number HQ680-AD1902 -- VENTRAC.COM Revised 12/07/20 Original Operator’s Manual 09.10112 Rev. 13...
- Page 2 To the Owner Contact Information and Product Identification If you need to contact an authorized Ventrac dealer for information on servicing your product, always provide the product model and serial numbers. Please fill in the following information for future reference. See the picture(s) below to find the loca- tion of the identification numbers.
-
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION PAGE 5 Product Description ............5 Why Do I Need an Operator’s Manual? . - Page 4 TABLE OF CONTENTS SERVICE PAGE 19 Cleaning and General Maintenance ..........19 Deck Flip-Up Procedure (Service Position) .
-
Page 5: Introduction
2-1/2 cm (1 inch) in diameter, the HQ680 mower makes short work out of heavy brush. The HQ680 tough cut mower can be set to three different cutting heights of 76, 92, or 108 mm (3, 3-5/8, or 4-1/4 inches). -
Page 6: Using Your Manual
Manual Glossary Power Unit A Ventrac tractor or other Ventrac engine powered device that may be operated by itself or with an attachment or accessory. Attachment A piece of Ventrac equipment that requires a Power Unit for operation. -
Page 7: Safety
SAFETY SAFETY General Safety Procedures for Ventrac Power Units, Attachments, & Accessories Training Required • The owner of this machine is solely responsible for properly training the operators. • The owner/operator is solely responsible for the operation of this machine and for the prevention of acci- dents or injuries occurring to him/herself, other people, or property. - Page 8 SAFETY General Safety Procedures for Ventrac Power Units, Attachments, & Accessories • Ensure that all bystanders are clear of the power unit and the attachment before operating. Stop the ma- chine if someone enters your work area. • Always be alert to what is happening around you, but do not lose focus on the task you are performing. Al- ways look in the direction the machine is moving.
-
Page 9: Keep Riders Off
SAFETY General Safety Procedures for Ventrac Power Units, Attachments, & Accessories • Know the work area well before operation. Do not operate where traction or stability is questionable. • Reduce speed when you are operating over rough ground. • Equipment can cause serious injury and/or death when improperly used. -
Page 10: Roadway Safety
• If the power unit, attachment, or accessory requires repairs or adjustments not instructed in the operator’s manual, the power unit, attachment, or accessory must be taken to an authorized Ventrac dealer for service. • Never perform maintenance on the power unit and/or attachment if someone is in the operator’s station. -
Page 11: Fuel Safety
SAFETY General Safety Procedures for Ventrac Power Units, Attachments, & Accessories • Check the fuel lines for tightness and wear on a regular basis. Tighten or repair them as needed. • To reduce the hazard of fire, keep the battery compartment, engine, and muffler areas free of grass, leaves, and excess grease. -
Page 12: Hydraulic Safety
SAFETY General Safety Procedures for Ventrac Power Units, Attachments, & Accessories • If the fuel tank must be drained, it should be drained outdoors into an approved container. • Check the fuel lines for tightness and wear on a regular basis. Tighten or repair them as needed. -
Page 13: Cutting Unit Safety
SAFETY HQ680 Safety Procedures Tall grass and thick brush can hide large obstacles such as rocks, tree stumps, etc. • Inspect the work area for hidden obstacles and remove or mark any obstacles before beginning operation. • Inspect the area to be mowed and remove all objects that the machine could potentially throw. -
Page 14: Safety Decals
SAFETY Safety Decals The following safety decals must be maintained on your attachment. Keep all safety decals legible. Remove all grease, dirt, and debris from safety decals and instructional labels. If any decals are faded, illegible, or missing, contact your dealer promptly for replacements. When new components are installed, be sure that current safety decals are affixed to the replacement components. - Page 15 SAFETY 1. Pinching or crushing hazard. 1. Read the operator’s manual. 1. Cutting or dismemberment hazard of hand or foot - mower blade. 2. Stay away from moving parts. 3. Keep all guards and shields in place. Decal Description Part Number Quantity Shield Missing 00.0625...
-
Page 16: Operational Controls
OPERATIONAL CONTROLS Jack Stand The HQ680 mower is equipped with a jack stand to keep the deck and the hitch arms positioned for quick and easy reattachment to the power unit. The jack stand has three positions: 1. Place the jack stand in the top position for mowing or transport. -
Page 17: General Operation
GENERAL OPERATION Daily Inspection Mowing and Operating Procedure WARNING CAUTION Always engage the parking brake, shut off the power Tall grass and thick brush can hide obstacles such unit engine, remove the ignition key, and ensure that as rocks, tree stumps, etc. Inspect the work area for all moving parts have come to a complete stop be- hidden obstacles and remove or mark any obstacles fore inspecting the components, or attempting any... -
Page 18: Transport Of Mower
GENERAL OPERATION Transport of Mower Cutting Height Adjustment (Optional Swivel Wheels) Transport the attachment with the power unit front WARNING hitch and attachment fully raised to reduce wear of the equipment. Travel slowly when transporting over undulating and rough surfaces to maintain control of Accidental lowering of the mower deck could trap a the power unit and to reduce the shock to the power person or appendage. -
Page 19: Service
ATTENTION If any component requires replacement, use only original Ventrac replacement parts. Cleaning and General Maintenance To return the deck to the operating position, remove the two pins (C) from the front of the hitch... -
Page 20: Mower Blade Inspection/Replacement
SERVICE Mower Blade Inspection/Replacement Belt Inspection CAUTION Inspecting the drive belts of the attachment can prevent sudden belt failure by finding problems before they cause a belt to break. Mower blades may be sharp. Always wear heavy Typical wear gloves when working with mower blades. on a drive Glazing 1. -
Page 21: Main Deck Belt Replacement
SERVICE Main Deck Belt Replacement 13. Tighten the outer nut on the idler adjustment rod to apply tension to the main deck belt until these 1. Detach the mower deck from the power unit. is approximately .8 - 1.6 mm (1/32 - 1/16 inch) gap 2. -
Page 22: Right Deck Belt Replacement
SERVICE Right Deck Belt Replacement Main Deck Belt Tension Adjustment 1. Detach the mower deck from the power unit. If the belt slips during normal mowing operation, the belt tension will need to be adjusted. 2. Open the main deck cover shield. 1. -
Page 23: Lubrication Locations
SERVICE Lubrication Locations Deck Leveling Procedure Lubrication is required at the following locations using 1. Park the power unit on a smooth, level surface. a lithium complex NLGI #2 grease. 2. Lower the mower deck to the ground and place the power unit’s primary SDLA lever in the float position Wipe the grease fittings clean before applying grease by pushing it to the right until the detent engages. -
Page 24: Storage
SERVICE Storage Preparing the Attachment for Storage 1. Clean the attachment to remove accumulated clip- pings, leaves, dust, or other debris. 2. Inspect for loose or missing hardware, damaged components, or signs of wear. Repair or replace any damaged or worn components. 3. -
Page 25: Maintenance Schedule
SERVICE Maintenance Schedule Maintenance Schedule Grease and Lubrication: See Lubrication Section Drive Shaft Bearing ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü Caster Wheel ü ü ü ü ü... -
Page 26: Specifications
Heavy duty deck construction Rear discharge deck design Flip-up deck design Field serviceable spindles Heavy duty mower blades View all manuals Visit ventrac.com/manuals for the latest version of this operator’s manual. A downloadable parts manual is also available. Specifications - 26... -
Page 27: Noise Emissions
Ryan Steiner Venture Products, Inc. Technical File Keeper 500 Venture Drive Orrville, OH 44667 Description Tough cut brush mowing attachment Model Name Ventrac HQ680 Tough Cut Model Number 39.55104 Serial Number HQ680-Axxxxx This Product Conforms to Directives 2006/42/EC Ryan Steiner... -
Page 28: Warranty
2-year All Ventrac add-on kits and accessories such as: 3-point hitch, 12V front & rear power outlets, foot pedal, dual wheel kit, etc., will be covered under the above warranty periods provided they are installed by an Authorized Ventrac Dealer. This warranty may be transferred and will carry the remainder of the warranty starting from the original purchase/registration date with the dealership and/or V.P.I. - Page 29 (i) damage or defects due to or arising out of repair of the Ventrac equipment by a person or persons other than an authorized Ventrac service dealer or the installation of parts other than genuine Ventrac parts or Ventrac recommended parts.