Congratulations on the purchase of a new VENTRAC HQ680 Tough Cut Mower! The purpose of this manual is to assist you in its safe and effective operation and maintenance. With proper usage and care, the Tough Cut Mower will provide many years of service.
INTRODUCTION Product Description The new VENTRAC Model HQ680 “Tough-Cut” rotary mower features an enclosed deck designed for field and brush mowing. The broad, belted, high intake front creates an “attack” on tall grasses and brush before it is leveled. The straight front deck design provides structural strength and a uniform performance in tall vegetation.
SAFETY ATTENTION This symbol identifies potential health and safety hazards. It marks safety precautions. Your safety and the safety of others is involved. SIGNAL WORD DEFINITIONS Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is limited to the most extreme cases.
The following decals must be maintained on your Ventrac Attachment. If any decals are faded or missing, contact your dealer promptly for replacements. Page & Decal Location E-1, #28 E-1, #20 E-1, #27 E-1, #15 (2) SAFETY Description Danger Shield Missing Warning Moving Part Hazard Danger Pinching Hazard Keep Hands and Feet Away...
SAFETY General Safety Procedures for Ventrac Tractors, Attachments, & Accessories Read and understand the operator’s manual before operating this equipment. Observe and follow all safety decals. DO NOT let children or any untrained person operate the tractor or attachment. Make sure that all operators of this equipment are thoroughly trained in using it safely.
Page 9
Before making any repairs or adjustments, lower attachment to the ground, set parking brake, shut the engine off, and remove the key. Read and understand the operator’s manual before • Do not mow in areas that contain stones, sticks or other foreign objects that may be thrown from the mower.
Setup Instructions for the HQ680 Tough Cut Mower Jack Stand Installation: To install the jack stand into the mounting tube as shown below, raise the back of the mower far enough to insert the stand in the tube. This can be accomplished be setting the mower crosswise on the crate or using a lifting device.
OPERATING INSTRUCTIONS Attaching: 1. Drive the tractor slowly forward into the mating arms on the mower. Align the hitch arms to complete the engagement. 2. Once completely engaged, close the front hitch latch. 3. Stop the tractor engine. 4. Place attachment belt over the outside groove of the PTO drive pulley on the tractor. 5.
OPERATION Operating Techniques and Tips: With a little practice, operation of the mower will become very easy and simple. Always keep SAFETY as the First Priority. Remember to keep the size of the task appropriate to the size of the equipment. Always shut off engine and remove key to clean or make adjustments on the mower.
Page 13
OPERATION Operating Techniques and Tips (cont.) Wet or lush grass has some tendency to build up under the deck. Clean deck periodically and particularly if and when mowing performance seems to be reduced. Cleaning Procedure 1. Raise the deck all the way up. 2.
Page 14
OPERATION Use of Duals for Mowing On level to modest inclines, single tires will suffice. Single tires should be inflated to 7 psi and outside dual tires to 3-4 psi. Lower inflation pressure reduces grass and soil compaction. On significant inclines, even if only a small portion of the total mowing to be done, the tractor should be equipped with dual tires for increased stability.
MAINTENANCE Lubrication Grease zerks are located as shown below. Apply 2-3 pumps of grease per spindle approximately every 50 hours of operation. All other bearings—one pump max! Do not over grease. In very dirty, sandy, or wet conditions, more frequent greasing may be advisable.
MAINTENANCE Removal and Reinstallation of Mower Blades for Sharpening or Replacement: Wear Heavy Gloves. 1. With the deck fully raised, place the tractor on a level surface. Set the parking brake and remove the key from the tractor. 2. Remove the latch pins, and lift the deck to the near vertical position. Reinstall the latch pins.
Belt Replacement: If belts become excessively worn or cracked, install a new belt. This is done most easily with the deck removed from the tractor. Main Deck Belt Replacement: 1. Remove old belt. Note that one belt loop must surround the left hitch arm. Remove left hitch arm for access.
Page 18
PARTS & DRAWINGS FIGURE 1 ILLUSTRATED DRAWING MAIN DECK...
Page 19
PARTS & DRAWINGS FIGURE 1 MAIN DECK REF. PART NO. DESCRIPTION QTY. 1 ..97.0506..5/16-18 x 3/4 Carriage Bolt ... . 7 2 .
Page 28
LIMITED WARRANTY – VENTRAC TURF EQUIPMENT Venture Products, Inc. (shall be referred to as V.P.I.) warrants on the terms and conditions herein, that it will repair, replace, or adjust any part manufactured by Venture Products Inc. and found by Venture Products Inc to be defective in material and / or workmanship.
Page 29
LIMITED WARRANTY – VENTRAC TURF EQUIPMENT operation of, or use of the turf equipment which is not in accordance with operating instructions as specified in the operator’s manual or other operational instructions provided by V.P.I.; (f) repair or replacement arising as a result of any operation from Ventrac turf equipment that has been altered or modified so as to, in the determination of V.P.I., adversely affect the operation, performance or durability of the equipment or that has altered, modified or affected the turf equipment so as to change the intended use of the product;...
Page 30
Claim processed by a Vanguard authorized servicing dealer to local distributor Claim processed by an application authorized Tecumseh servicing dealer to application Tecumseh Venture Products year prorated processes warranty year prorated Venture Products year prorated processes warranty year prorated Venture Products application...