Subscribe to Our Youtube Channel
Related Manuals for NewLine Raymor RAY1200CHR
Summary of Contents for NewLine Raymor RAY1200CHR
- Page 1 SLIDING DOOR SET INSTRUCTION MANUAL PRODUCT CODES: RAY1200CHR RAY1200WHT INSTRUCTION MANUAL VERSION: 16/0001 Newline Group Limited Freephone 0508 639 5463 | www.newline.co.nz...
-
Page 2: Table Of Contents
PLEASE READ THROUGH AND UNDERSTAND ALL INSTRUCTIONS BEFORE INSTALLATION AND USE. CONTENTS PAGE Important Information ... 1 Preparation Checklist ... 2 Supplied Components ... 3 Layout Procedure ... 5 Installation Steps ... 6 Newline Group Limited | Freephone 0508 639 5463 | www.newline.co.nz... -
Page 3: Important Information
When you receive your Raymor shower check contents for any freight damage. Advise Newline on 0508 639 5463 if any damage has occurred within 8 hours of receiving the goods so this is can rectified. Do not proceed with installation until resolved. -
Page 4: Preparation Checklist
2 Sided Shower: Ensure the floor is level and the walls are plumb and flat. Position all framing for solid fixing for the shower tray, shower and plumbing fittings (refer to the specific tray, liner and shower instruction manual at www.newline.co.nz). Ensure all plumbing items have been installed prior to the lining being attached. -
Page 5: Supplied Components
SUPPLIED COMPONENTS Description Parts Number Wall Posts Screws M4x3/8" PACK Screw Cover Caps PACK Screws M4x1 3/8" PACK Screws M4x5/16" PACK Spacer Blocks Return Panel Handle Set Top Rollers Water Deflectors Door Panel Bottom Rollers Top/Bottom Rollers Fixed Panels Glass Clamp Raymor Showers / Pivot Door Set Page 3... -
Page 6: Layout Procedure
LAYOUT PROCEDURE / 2-Sided Shower ACRYLIC TRAY APPLICATION • Installation of the tray and liner must be completed as per separate instructions pacakged with the Tray. • Mark out the outside boundary line 22mm in from the outside of the Tray (refer Diagram A). This measurement will allow for walls out of plumb up to 8mm. -
Page 7: Installation Steps
INSTALLATION STEPS / 2-Sided Configuration STEP 1 1. Referring to the Assembly Layout Plan (Page 5), set up and plumb Wall Channels on boundary line. 2. Apply silicone to back of wall channels and fasten to the wall ensuring that they remain plumb. - Page 8 STEP 2 Assembly of Door Frame Components: Top and bottom rails (13) Fixed front panel (14) Corner post (17) Spacer Blocks(6) 4 x 35mm screws (3) Two spacer Blocks (6) Two Glass clamps( 16) and 2 screws 4 x1 0mm. Note: Refer back to Assembly Drawing on page XX to reference numbers.
- Page 9 STEP 3 Slide Door assembly and Return panel into the wall channels. (1) Bring together the two panel assemblies together at the corner (2). Adjust the Door and Return Panels evenly on the tray and into the Wall channels (1). Bring the corner joint together and drill and fasten this point (2).
- Page 10 LAYOUT PROCEDURE / Alcove Configuration ACRYLIC TRAY APPLICATION • Installation of the tray and liner must be completed as per separate instructions. • We recommend using GIB Aqualine® 13mm or equivalent for both sides of the Alcove. This is optimum width. •...
- Page 11 INSTALLATION STEPS / Alcove Configuration STEP 1 1. Mark out the Wall Channels up the wall as indicated to establish the outside boundary line. 2. Take one Wall Channel only, apply silicone to the back and fasten to the wall. Note: Flange to the inside.
- Page 12 STEP 3 / Fitting to Alcove 1. Slide the remaining wall channel onto the opposite side of the door assembly. 2. Install the Door assembly into the initial wall channel on the wall. 3. Apply silicone to the back of the opposite wall channel and fasten at the boundary line. 4.
Need help?
Do you have a question about the Raymor RAY1200CHR and is the answer not in the manual?
Questions and answers