FireAngel WST-630 User Manual
Hide thumbs Also See for WST-630:

Advertisement

User Manual
Wireless Interlink
Smoke Alarm + 10 Year Life
WST-630
Please retain this user manual for future reference
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WST-630 and is the answer not in the manual?

Questions and answers

Summary of Contents for FireAngel WST-630

  • Page 1: 301489-3 V1 6

    User Manual Wireless Interlink Smoke Alarm + 10 Year Life WST-630 Please retain this user manual for future reference...
  • Page 2: Table Of Contents

    651d/12 Smoke Alarm Devices Hereby, Sprue Safety Products Ltd, declares that this DoP: SADOPWST-630-01 WST-630 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC The declaration of conformity may be consulted at http://spru.es/EC-WST-630 Note: This User Manual is also available in large text and other formats...
  • Page 3: Introduction

    INTRODUCTION thermal enhancement, providing fast response to both fast flaming and smouldering fires, eliminating the need for ionisation sources IMPORTANT: This user manual contains which can be harmful to the environment important information regarding the operation of your smoke alarm Ensure you read this user The state of the art thermally-enhanced optical manual fully before installing and operating the sensing chamber provides a fast reaction to...
  • Page 4: Positioning

    Your WST-630 smoke alarm can be used in individual sleeping/resident rooms, providing the same conditions are met as for a single- BEDROOM HALL BEDROOM family residence However, there must already be a primary fire detection system that meets...
  • Page 5: How To Install Your Smoke Alarm

    It is recommended not to exceed 35m as the maximum distance between smoke alarms in the network Note: Up to 50 WST-630 smoke alarms and/ HOW TO INSTALL YOUR or Wi-Safe 2 accessories can be learned in to a single network.
  • Page 6: Interlinking Your Wst-630 Smoke Alarms

    Therefore WST-630 alarms need to be “learned in” or interlinked in 3. Fit Your Smoke Alarm To fit to the base plate included in this pack, order to communicate with each other If...
  • Page 7 products within the Wi-Safe 2 range “Learning in” (interlinking) your Smoke Alarms: The process below describes ‘learning in’ two alarms into a network, “Alarm 1” and “Alarm 2” 1. Alarm 1: Install Alarm 1 as described Alarm 1 will give an audible sound consisting of previously 2 cycles of 3 loud beeps 2.
  • Page 8: Operation

    “chirp” approximately once every once again by following the “learn-in” process 45 seconds All other WST-630 alarms in the on page 7 network will also emit an audible low battery chirp once every 4 hours...
  • Page 9: Led Indicators

    45 seconds seconds after the fault red LED flash immediately red LED Note: The amber LED may flash twice on the WST-630, indicating that the fault is with the wireless module In this event, the complete WST-630 alarm should be replaced...
  • Page 10: Alarm Test

    WARNING: As with all electronic products you should test your smoke alarm every week a) Briefly press the test button in the centre If your WST-630 is interlinked with other smoke and release alarms, we recommend that every individual smoke alarm is tested during the weekly test...
  • Page 11 If your WST-630 is interlinked with other alarms, pressing the test button will also silence other alarms in the network However, any alarm 2.
  • Page 12: Maintenance

    MAINTENANCE Your smoke alarm may false alarm when it is being cleaned using a vacuum cleaner Your smoke alarm has been designed to be IMPORTANT: Do not use solvents or cleaners as maintenance-free as possible, however on your smoke alarm, as they may cause there are several things you must do to keep it damage to the sensor or circuitry The unit can working properly...
  • Page 13: Troubleshooting

    TROUBLESHOOTING Problem Solution • Make sure the alarm has been rotated clockwise as far as it can go and is securely located on its base plate • If testing after first activating the alarm, allow a few seconds for the alarm to settle before testing •...
  • Page 14 If you have any questions about the operation of your alarm, please contact operate correctly, Technical Support between 9am - 5pm Monday – Friday. Telephone: 0800 the advice of the 141 2561 or e-mail: technicalsupport@fireangel.co.uk You can also visit manufacturer should the support section of our website www.fireangel.co.uk be sought...
  • Page 15: Disposal

    Sprue Safety Products Ltd, at its discretion, agrees to replace the unit free of charge The warranty on any replacement WST-630 alarm, will last for the remainder of the period of the original warranty in respect of the alarm originally purchased – that is...

Table of Contents