SPECIFICATIONS 2. WARNINGS 3. INSTALLATION 4. OPERATION AND MAINTENANCE 5. VARIABLE SPEED PUMP OPERATION 5.1 Buttons and display 5.2 Speed setting buttons 5.3 Pump starting and stopping 5.4 High speed start function 5.5 Memory function when power off 5.6 Over/ under voltage protection 5.7 Overload protection 5.8 Locked rotor protection 5.9 IPM module...
DPX 3000 PUMP The DAYLIFF DPL range of swimming pool pumps are quiet running and reliable products suitable for all domestic pool applications. All models feature a large strainer basket with easy-open transparent cover and connecting unions and all hydraulic components are made from high strength glass reinforced corrosion resistant polypropylene for long life.
Page 5
The DAYLIFF DPX range of swimming pool pumps are quiet running and reliable products suitable for light and medium duty pool applications. All models feature a large strainer basket with easy-open transparent cover and connecting unions and all hydraulic components are made from high strength glass reinforced corrosion resistant polypropylene for long life.
PUMP DATA Dimensions (mm) Voltage Speed Power Current Weight Model (rpm) (kW) (kg) DN1/DN2 DPL 550 0.55 DPL 750 0.75 2850 DPL 1100 100%/3500 DPL 1100VS 1x240 80%/2850 50%/1800 DPX1100 DPX1500 2850 DPX3000 3x415 The pump may contain small quantity of residual water from testing.
Page 7
The mains voltage must be the same as that shown on the motor plate. Ensure the earth connection is properly done. The pump should be installed in a well protected and ventilated place. The pump should never run dry. The motor should not be wrapped in plastic bags due to risk of condensation.
Page 8
Single phase motors are provided with overload protection; they are connected directly to the power mains. The pump should be turned off before repairing, to avoid accidents. For DPL 1100VS, Do not make a static voltage test of the controller, as it will cause damage to the controller.
3. INSTALLATION Installation, electrical connection and commissioning must be carried out by skilled personnel in compliance with local safety regulations. Failure to comply with these instructions causes risk to personal safety, damages the equipment and validates warranty. Installations should be done on a firm flat base not Ÿ...
In the interest of safety and reliability, only use Ÿ genuine Dayliff spares, or else warranty will become null and void. R e f e r t o D a y l i f f w e b s i t e - Ÿ...
The pump is equipped with a thermal overload protection. If overload occurs during Ÿ operation, the build in overload protection automatically deactivates the pump. The pump will switch on automatically after a cooling period of approximately 3 minutes, ensure the cause of the overload is identified and addressed. All work listed in this manual must be performed regularly.
5.1 Buttons and display The pump operator panel is equipped with 100% full speed button, 80% speed button, 50% speed button, switch button, speed increase and reduction buttons. The LED screen displays running speed or the maximum speed value corresponding to the percentage of the setting speed.
5.7 Overload protection If the operating current is more than the set value of 6.2A, the pump will stop running which is registered as malfunction fault. 5.8 Locked rotor protection Upon starting the pump, the current is monitored for 5secs, if the value exceeds the set value of 6.2A, the controller will stop the pump which is registered as Locked rotor.
Page 14
Basket or impeller clogged Clean basket or impeller Low flow rate; low pressure in filter Air getting into the suction Prime suction pipe pipe Delivery pipe choked Straighten the pipe Low flow rate; high pressure in the filter Pump filter clogged Clean pump filter Wrong impeller fitted Replace the impeller...
7. TERMS OF WARRANTY I) General Liability • In lieu of any warranty, condition or liability implied by law, the liability of Davis & Shirtliff (hereafter called the Company) in respect of any defect or failure of equipment supplied is limited to making good by replacement or repair (at the Company's discretion) defects which under proper use appear therein and arise solely from faulty design, materials or workmanship within a specified period.