Subscribe to Our Youtube Channel
Related Manuals for DAYLIFF DDA
Summary of Contents for DAYLIFF DDA
- Page 1 Submersible Well Pumps DDA 1000P DDA 600C/1200C2 DDA 900C Installation & Operating Manual...
- Page 3 INDEX PUMP SPECIFICATIONS 2. INSTALLATION MAINTENANCE TROUBLE SHOOTING WARRANTY © Davis & Shirtliff Ltd 2022 Contents herein are not warranted...
-
Page 4: Pump Specifications
Congratulations on selecting a Dayliff DDA Pump. They are manufactured to the highest standards and if installed and operated correctly will give many years of efcient and trouble free service. Careful reading of this Installation Manual is therefore important, though should there be any queries they should be referred to the equipment supplier. - Page 5 Max. Immersion Depth: DDA1000P-6m, DDA600C & DDA1200C2-20m; DDA900C-16m PUMP DATA Max. Max. Dimensions (mm) Power Outlet Weight Model Particle Current (”) (kg) Size, mm DDA 600C 0.55 0.75 DDA 1200C2 0.92 DDA 1000P DDA 900C DDA 900C DDA 1000P DDA 600C & DDA 1200C2...
-
Page 6: Installation
When using a hose, screw a suitable hose adapter onto the pump outlet and secure the hose with a clamp. DDA 1200C2 and DDA1000P need an area of at least 50 × 50 cm (the Ÿ floatswitch must be able to move freely so that it functions properly). These are fitted with an inbuilt capacitor and thermal control and can be connected to mains power directly after a 10A MCB or fuse. -
Page 7: Maintenance
Do not lift the pump with the cable or pressure hose as these are not designed to carry the weight of the pump. WARNING Using a strong rope, submerge the pump at an Ÿ angle into the water so that no air pocket forms on the underside of the pump. -
Page 8: Troubleshooting
4. TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE SOLUTION No power Check connections and power supply Motor overheating due to: Eliminate the cause of overheating i) Liquid temperature being too high Pump does not ii) Blocking by foreign bodies Residual current circuit breaker Reset circuit breaker triggered Motor defective... -
Page 9: Terms Of Warranty
5. TERMS OF WARRANTY i) General Liability • In lieu of any warranty, condition or liability implied by law, the liability of Dayliff (hereafter called the Distributor) in respect of any defect or failure of equipment supplied is limited to making good by replacement or repair (at the Distributor’s discretion) defects which under proper use appear therein... - Page 12 INS300D-07/20...
Need help?
Do you have a question about the DDA and is the answer not in the manual?
Questions and answers
Apart from immersion in clean water and avoiding the pump running dry,how else should I maintain my DAYLIFE DDA 1200 C2 PUNP
The maintenance tips for the DAYLIFF DDA 1200C2 pump include:
- Checking the float switch operation by lifting and shaking it to ensure free movement of the contained weights.
- Rinsing the pump with clean water to remove particles; a brush and detergent may be used.
- Submerging the pump in a container with clean water and switching it on briefly to rinse the inside.
- Cleaning all accessible areas of the casing and removing fibers wound around the rotor shaft by opening the pressure connection.
- Soaking the pump after long storage to remove any dirt residues.
This answer is automatically generated
@Mr. Anderson Thanks very much Mr.Anderson for helping tips about my pump maintenance
What distance can my day DDA 1200C2 Cover while pumping whater
The pumping distance of the DAYLIFF DDA 1200C2 is not explicitly mentioned. However, the maximum immersion depth for the DDA 1200C2 is 20 meters.
This answer is automatically generated
Do I need to put oil in my pump like any devices that are run by engine??
No, the DAYLIFF DDA pump has a single mechanical seal in an intermediate oil chamber for greater reliability. There is no indication that oil needs to be added.
This answer is automatically generated
How can I connect the DDA 1200ca 4 wires to the AVS??
How can I connect DDA 1200ca pump wire to the AVS