Bosch PST 900 PEL Original Instructions Manual page 19

– Then push the base plate (8) towards the saw blade (20)
as far as it will go.
– Retighten the screw (26).
PST 1000 PEL (see figure I):
– Open the base plate clamping lever (7) and push the base
plate (8) slightly towards the extraction outlet (4).
– The base plate has lock-in points at 0°, 22.5° and 45° on
the left and right so that the precise mitre angle can be
adjusted. Swivel the base plate (8) to the desired posi-
tion according to the scale (25). Other mitre angles can
be adjusted using a protractor.
– Then push the base plate (8) towards the saw blade (20)
as far as it will go.
– Close the clamping lever (7) to lock the base plate in the
set position.
Cut Control for mitre cuts (PST 900 PEL/PST 9500 PEL)
(30) (13) (14) (8)
To enable you to track the cutting line (Cut Control), the
viewing window for Cut Control (13) has a mark (30) for
right-angled cuts at 0° and a mark (31) for rightward- and
leftward-slanting mitre cuts at 45° according to the scale
(25).
The cut mark for mitre angles between 0° and 45° is propor-
tional. It can also be marked on the viewing window for
Cut Control (13) using a non-permanent marker and easily
removed again.
We recommend making a test cut for precise results.
Cut Control for mitre cuts (PST 1000 PEL)
(31) (13) (14) (25)(8)
To enable you to track the cutting line (Cut Control), the
viewing window for Cut Control (13) has a mark (30) for
right-angled cuts at 0° and a mark (31) for rightward- and
leftward-slanting mitre cuts at 45° according to the scale
(25).
When securing Cut Control with the base for Cut Control
(14) to the base plate (8), use the inner marking (31).
When securing the viewing window for Cut Control (13) dir-
ectly to the glide shoe (12), use the outer marking (32).
Bosch Power Tools
The cut mark for mitre angles between 0° and 45° is propor-
tional. It can also be marked on the viewing window for
Cut Control (13) using a non-permanent marker and easily
removed again.
We recommend making a test cut for precise results.
Moving the base plate
You can move the base plate (8) back for sawing close to
edges.
PST 900 PEL/PST 9500 PEL (see figure H):
– Pull the saw blade storage compartment (22) out of the
– Loosen the screw (26) and push the base plate (8) to-
– Retighten the screw (26).
PST 1000 PEL (see figure I):
– Open the base plate clamping lever (7) and push the base
– Close the clamping lever (7) to lock the base plate in the
Sawing with an offset base plate (8) is only possible with a
mitre angle of 0°. In addition, Cut Control must not be used
with the base (14), the parallel guide with circle cutter (28)
(accessory) or the anti-splinter guard (23).
(31) (25)
Sawdust blower device
The cutting line can be kept clear of chips using the airflow
from the sawdust blower device.
Starting Operation
u
(32) (12) (25)
Switching on the LED worklight
The worklight (15) improves visibility in the immediate work
area. You can achieve particularly good sawing results by us-
ing the worklight together with Cut Control.
Switch on the worklight (15) by lightly pressing the on/off
switch (3). If you press down harder on the on/off switch,
the power tool will switch on and the worklight will remain il-
luminated.
base plate (8).
wards the extraction outlet (4) as far as it will go.
plate (8) towards the extraction outlet (4) as far as it will
go.
set position.
To switch on the sawdust blower
device: When working with high mater-
ial removal in wood, plastic and other
similar materials, push the switch (10)
towards the extraction outlet.
To switch off the sawdust blower
device: When working in metal and with
a dust extraction system connected,
push the switch (10) towards the saw
blade.
Pay attention to the mains voltage. The voltage of the
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230 V can also be operated with 220 V.
1 609 92A 684 | (17.02.2021)
English | 19