Advertisement
Available languages
Available languages
T-
ART/G2+
TELEPHONE
SAFETY PRECAUTIONS
-
Always disconnect the power supply before making modifications to the device.
-
The fitting and handling of these devices must be carried out by
-
The wiring must run at least 40 cm away from any other wiring.
-
Do not overtighten the screws on the connector.
-
Install the
T-ART lephone
te
in a dry protected location free from the risk of dripping or splashing water.
-
Do not place in humid, dusty or smoky locations, or near sources of heat.
-
Before connecting the device to the mains, check the connections between the door panel, power
supply and
T-ART telephones
.
-
Always follow the instructions contained in this manual.
( )
CHARACTERISTICS
*
-
T-ART lephone
te
with simplified installation (non-polarised 2 wire bus).
- Up to 4
T-ART
telephones
/monitors per apartment (master, slave 1, slave 2 and slave 3).
- Up to 32 apartments/T-ART terminals in mixed installations with monitors
- Up to 128 apartments/
T-ART
terminals per installation
- Completely private conversation.
- Call reception volume control: min, med, max and off (do not disturb).
- Audio volume control during communication process (4 different levels).
-
"HZ" i
nput for calls from
apartment front
door.
.
- Output to auxiliary call repeater (maximum 50mA/12Vdc).
-
Up to 6 d
ifferent ringtones to identify the origin of the call (door panel, intercom
front door of the apartment).
- Button
for lock release 1 activation. In standby
"Doctor mode".
- Button
for lock release 2 activation/ staircase light activation (SAR-G2
required) / "intercom" calls (within the same apartment) and "autoswitch-on" function.
- Button
for tone call volume control, "do not distrurb" mode/ configuring ringtones/ communication call
volume control (T-ART speaker) & in case of call forwarding, cancel call transfer (with ART 7W monitor).
- Button
for guard monitor calls (if exist).
- DIP switches for setting the te
lephone
's address (call code), master/slave and end of line.
SYSTEM OPERATION
-
To make a call, the visitor needs to press the button for the apartment, an audible tone indicates
that the call is being made and LED
on the door panel illuminates. If vocal synthesis is enabled,
a 'Call is in progress' message appears indicating that a call is being made. At this moment, the
apartment's te
lephone
(s) receives the call. If another apartment is called by mistake, press the
button for the correct apartment and the first call will be cancelled.
- Upon receiving the call,
the telephone's LED
seconds,
the door panel's
LED
will turn off
the channel will be freed.
-
To establish communication,
lift the handset
LED
will turn off, the led
will
turn on and the telephone's LED
-
Communication will last for one and a half minutes or until
communication has finished,
door panel's
synthesis is
enabled
, a 'Communication is finished' message will indicate that the call is over.
-
To open the door, press button
(if it exists and, to open the second door, press button
during the call or communication processes: one press activates the lock release for seconds
and LED
on the door panel will also illuminate for
'Door
is op
en' message will be indicated on the door panel.
-
Description of the function buttons can be found on p. 3.
( )
*
For more information, see
"T -ART/G2+"
T
https://doc.golmar.es/search/manual/50122719
authorised personnel
.
(EL632 G2+ SE module)
(EL6 2 G2 sound module required).
4
+
, guard monitor
(handset on or off the hook)
: activate/ deactivate
+ &
SAR-12/24 modules
will blink white. If the call is not answered within 40
, the telephone's LED
switch on (white color)
on any te
lephone
in the apartment
.
Door panel's
switch on (white color)
the handset is replaced
LED
will turn off and the channel will be freed. If vocal
3
3
seconds. If vocal synthesis is enabled, a
user manual (code 5012
2719
).
2
T-
ART/G2+
( )
DESCRIPTION OF THE TELEPHONE
*
Description:
a
a.
Handset.
b.
Function push buttons.
.
c.
Raised dots for the visually impaired people.
In call
/communication
Above these raised dots is the 'Door opening'
button.
d.
Status LEDs.
Function push button:
In standby (handset off the hook): One short press for
guard monitor calls (if exist).
or
During the call or communication processes: one press
will activate the lock release 2. In standby (handset on the
hook): press the button for 3 sec. to activate the staircase
light
(SAR-G
2+
&
press to default tones & tones volume (led
times).
In standby (handset off the hook):
"intercom" call (within the same apartment)
3 seconds to "autoswitch-on" function.
( )
*
Function push button status LED:
-
In standby:
Led switch on (white color).
panel, guard or intercom process: Led will blink (white color).
Terminal in communication: Led switch on (white color).
-
"Do not disturb" mode
default tones & tones volume: Led blink 9 times (red color).
-
"Automatic door opening" Doctor mode:
color).
( )
*
Description of the DIP switch and conf guration of the
Dip1 Dip :
-
7
Sets the
terminals
The switches set to OFF have a zero value. The values of the switches set to ON are shown in the table below. The
terminal code is the sum of the values of the switches set to ON.
and
Important:
Apartment 1 (Dip1 to ON & Dip2-Dip7 to OFF).
Apartment 128 (Dip1-Dip7 to OFF).
.
.
Dip -Dip :
8
9
These define whether the
. When
.
Master
ON
1
2
3
4
5
6
7
8
)
Dip
10 Configures the end of line. In installations with terminals only, it must always be in the OFF position. In
:
mixed installations of monitors with
in which the BUS cable ends and leave in the OFF position for intermediate terminals.
.
( )
*
IMPORTANT: T-ART/G2+ terminal in
manual for Kit features as maximum number of apartments and monitors/ T-ART/G2+ terminals.
( )
*
For more information, see
https://doc.golmar.es/search/manual/50122719
EN
TELEPHONE
e
AUX
f
g
b
h
i
c
e
d
e.
Wall mounting connector fixing (x4).
f.
Golmar use.
g.
Configuration switches.
h.
:
Bus connection terminals.
i.
Label.
j.
Apartment front door button input.
k.
Auxiliary call repeater output (max. 50mA/12Vdc).
During the call or communication processes: one press
will activate the lock release 1. In standby (handset
on or off the hook): press the button for 5 sec. to
activate/deactivate the "Doctor mode" function.
In standby (handset on the hook): short press, it allows
to change tone call volume, on every short press
SAR-12/24
modules required 5 short
).
te
lephone
med/ max/ off "do not disturb").
blink 9
2 short press to
every short press, it allows to change the speaker of
the T-ART audio volume (cyclic 4 audio levels). Other
and
press for
settings see "TT-ART/G2+" user manual.
Description connection terminals:
During call door
: Led switch on (red color).
To confirm
Led switch on (red
i
T-ART/G2+
Building / Villa (Nexa Door Panel)
address (addresses to
1
128
).
Note:
Mixed installations with monitors (addresses 1 to 32).
Table of values
Switch number : 1 2 3 4 5
Value when ON 1 2 4 8 16
:
32 64
terminal
is master or slave. Each apartment must have
Slave 1
Slave 2
ON
ON
9 10
1
2
3
4
5
6
7
8
9 10
1
2
3
4
5
6
T-ART/G2+
te
lephones
in the same apartment, set to ON for the te
Villa installation with SOUL door panel
"T -ART/G2+"
T
user manual (code 5012
3
j
k
BUS
HZ
GND
SA
OFF = 0 | ON = 1
DIP 1 to 7
DIP 8,9
Monitor address
00 - Master
10 - Slave 1
DIP 10
01 - Slave 2
End of line resistor
11 - Slave 3
GOLMAR S.A. C/ Silici, 13. 08940-SPAIN
reproduces the selected volume (cyclic min/
In communication:
on
(Auxiliary call repeater
SA
GND
output
, max. 50mA/12Vdc).
HZ
(
Door bell connection)
.
HZ
BUS
connection
(non-polarised)
.
terminal address (code):
ON
6
7
1
2
3
4
5
6
7
8
9
10
Example: 0+ 0+4+0+ 16 0+0
+
= 20
only
one master
terminal
.
Slave 3
ON
7
8
9 10
1
2
3
4
5
6
7
8
9 10
lephones
, see corresponding Kit Soul user
2719
).
EN
Advertisement
