Preparations For Use - Scandomestic SKF 433 X User Manual

Level ground
Place the freezer on the solid and flat ground (floor) to keep it stable, or else, it will
give rise to vibration and noise. When the freezer is placed on such flooring mate-
rials as carpet, straw mat, polyvinyl chloride, the solid backing plates should be
applied underneath the freezer, so as to prevent color change due to heat dissi-
pation.
Unobstructed ventilation shall be maintained around the appliance or in an em-
bedded structure.

Preparations for use

Standing time
After the freezer is properly installed and well cleaned, do not switch it on imme-
diately. Make sure to energize the freezer after more than 1 hour's standing, so
as to ensure its normal operation.
Cleaning
Confirm the accessory parts inside the freezer and wipe the inside with a soft
cloth.
Power-on
Insert the plug into the solid socket to start the compressor. After 1 hour, open
the freezer door, if the temperature inside the freezer compartment drops obvi-
ously, it indicates the refrigeration system is working normally.
Storage of food
After the freezer runs for a period of time, the internal temperature of the freezer
will be automatically controlled according to the user's temperature setting. After
the freezer is fully cooled, put in foods, which usually need 2-3 hours to be fully
cooled. In summer, when the temperature is high, it takes more than 4 hours for
the foods to be fully cooled (Try to open the freezer door as less as possible before
the internal temperature cools down).
If the freezer is installed in the moisture place, make sure to check whether the
ground wire and leakage circuit breaker are normal. If vibration noises are pro-
duced due to the freezer contacting the wall or if the wall gets blackened by air
convection around the compressor, move the freezer away from the wall. Setting
up the freezer may cause jamming noise or image chaos to the mobile phone,
fixed-line telephone, radio receiver, television surrounding it, so try to keep the
freezer as far away as possible in such case.
Functions
The display panel is designed on the fridge
door, illustrated as the figures below:
Function Setting
When the refrigerator system is connected
to power supply for the first time, all icons
on the display panel gets illuminated for 2s,
and the fridge temperature is controlled at
5℃, and the freezer temperature at -18℃
by default. When all the doors are close,
the display gets extinguished automatically
if no key operation within 3 minutes. When
the display is off, it will light up if any door
is opened or any key is pressed.
The following key operations are valid only when the keys are unlocked and gets
illuminated on the display.
Fridge temperature setting
When the fridge temperature setting function is not active, press the "Fridge" key
for the first time, then the icon of the current temperature mode starts flashing,
with the fridge temperature subjected to change. At this point, press the "Fridge"
key again, then the fridge temperature values will cycle as following:
（quick cooling）→2→4→5；
5→6→8→
During the temperature setting process, the icon of the selected temperature
mode keeps flashing, and if no key operation within 5 seconds, it stops flashing,
with the fridge temperature setting taking effect automatically.
Freezer temperature setting
When the freezer temperature setting function is not active, press the "Freezer"
key for the first time, then the icon of the current temperature modes starts flash-
ing, with the freezer temperature subjected to change. At this point, press the
"Freezer" key again, then the freezer temperature values will cycle as following:
（fast freezing）→ -16 → -18
-18→ -20 → -22 → -24 →
During the freezer temperature setting process, the icon of the selected temper-
ature mode keeps flashing, and if no key operation within 5 seconds, it stops flash-
ing, with the freezer temperature setting taking effect automatically.
Fast Freeze
When the Fast Freeze function is enabled, the freezer temperature will be con-
trolled at -32℃ automatically, and after 26 hours of running, the Fast Freeze func-
tion gets exited. Cooling down the freezer temperature in a rapid manner is ben-
eficial to the prevention of food nutrition against lost and the preservation of
freshness.
Under the Fast-Freezing mode, the freezer temperature is subjected to no adjust-
ment.
Quick Cooling
1When the quick cooling function is activated, the fridge temperature will be con-
trolled at 2℃.
Door open alarm
If any door is open for more than 3 minutes, buzzer alarms will be continuously
issued, which can be stopped when any key is pressed, but will be restored after
3 minutes if the door keeps open. The alarms will not be lifted until the door is
closed.
Power cut memory
In the case of power failure, the refrigerator will maintain the running state that is
set before the power outage when the power supply is restored.
Power-on delay
In order to protect the refrigerator compressor from being damaged in the case
of short-time power failure (i.e., less than 5 minutes), the compressor will not be
started immediately after it is powered on.
Fault alarm
1. Fridge sensor fault: The corresponding indicator light of 2℃ keeps flashing,
while all the other fridge indicator lights are ON.
2. Ambient temperature sensor fault: The corresponding indicator light of 4℃
keeps flashing, while all the other fridge indicator lights are ON.
3. Freezer sensor fault: The corresponding indicator light of -16℃ keeps flashing,
while all the other freezer indicator lights are ON.
4. Freezer evaporator sensor fault: The corresponding indicator light of -18℃
keeps flashing, while all the other freezer indicator lights are ON.
5. Communication fault: The indicator lights of Quick Cooling and Fast Freezing
keeps flashing synchronously, while all the other indicator lights are ON.