Overview Of Settings - BEA IXIO-DT3 User Manual

OVERVIEW OF SETTINGS

BASIC
Back
More
PRESETTINGS
RAD: FIELDSIZE
small
RAD: OUTPUT
IR: IMMUNITY
IR: FREQUENCY
More
Back
ADVANCED
Back
More
RAD: IMMUNITY
radar
RAD: DIRECTION
off
RAD: HOLDTIME 0.5 s
IR: WIDTH
+
service
IR: NUMBER
mode
IR: PRESENCE TIME
motion
IR: OUTPUT
REDIRECTION
motion
SMART DAISY CHAIN*
FACTORY RESET
DOOR BELL*
More
Back
DIAGNOSTICS
ZIP CODE all parameter settings in zipped format
(see application note on ZIP CODE)
ID # unique ID-number
ERROR LOG last 10 errors + day indication
IR: SPOTVIEW view of spot(s) that trigger detection
IR: C1 ENERG signal amplitude received on curtain 1
IR: C2 ENERG signal amplitude received on curtain 2
0 1 2 3
shopping
critical
standard
street
env.
> > >
NO
NC
NC
NC
NO
NC
< 2.8 m
normal high
low
Sensors mounted close to each other should
A B
have a different frequency.
factory value
low >
uni
bi uni
PRM
1 s 2 s 3 s
service mode = no IR detection during 15 minutes (maintenance).
1 2
This value excludes conformity of the door system to EN 16005 and DIN 18650.
15 s 30 s 1
min
NC
NO NC
NO
NC
NC
motion motion opening output is active in case of: 0 motion detection
or and
presence presence
off 1/2 2/2 1/3
off 0.05 s 0.10 s 0.25 s
4 5 6 7
factory values for radar immunity, IR immunity, IR number and redirection
increased immunities, 1 curtain
increased immunities, redirection = motion and presence
> > >
current freq
NO NO: normally open
NC: normally closed
NC NC
NO
> 2.8 m
higher highest normal high
excludes conformity of the door system according to EN
16005 / DIN 18650. IR Immunity on values 4 or 5 is
incompatible with IR presence time on value 0
not allowed when the sensor is used in emergency exits
> > > >
uni
uni bi
PRM
AWAY Shop Shop
Shop
4 s 5 s 6 s 7 s
2 5 10 20 min 60 min infinite
min min min
current freq
NO
NO: normally open
NC NC
NO
NC: normally closed
1 motion or presence detection
2 motion and presence detection
1/2: 1 sensor in chain of 2; 2/2: 2
st
2/3 3/3
1/3: 1 in chain of 3; 2/3: 2
st
0.50 s 0.75 s 1 s 1.5 s
POWERSUPPLY
OPERATINGTIME
RESET LOG
PASSWORD
LANGUAGE
ADMIN
8 9
Freq : freq. in
no detection
> large
(100 Hz)
current: current
**
Inv.freq.
output
Inv.freq.: freq. in
NC
detection (2.5Hz)
For conformity to EN 16005 or DIN 18650 at a
mounting height of 2.8 m or more, use values
6 and 7.
high
>
PRM: for persons with reduced mobility
AWAY: unidirectional motion away from sensor
shop: automatic adaptation of field size (small shops)
8 s 9 s
Always additionally adjust
the arrow position on the
sensor with a screwdriver.
min. value for DIN18650: 1 min
min. value for EN16005: 30 s
sensor in chain of 2
nd
in chain of 3; 3/3: 3 in chain of 3
nd rd
full partial: outputs are
partial
not reset
reset
reset
2 s 5 s
* Setting in combination with an accessory (see p. 1).
For more information see user's guide of accessory.
**Setting accessible via LCD only
supply voltage at power connector
power duration since first startup
delete all saved errors
LCD and remotre control password
(0000= no password)
language of LCD-menu
enter code to access admin mode
5