Page 1
WELLS BLOOMFIELD, LLC 2 ERIK CIRCLE, P. O. Box 280 Verdi, NV 89439 telephone: 775-689-5703 fax: 775-689-5976 www.wellsbloomfield.com OPERATION MANUAL WELLS COUNTERTOP HW-Series COOK ’N HOLD WARMERS Model HW-SMP with THERMOSTAT CONTROL Includes INSTALLATION USE & CARE Model HW-10 IMPORTANT: DO NOT DISCARD THIS MANUAL...
Page 2
The prices charged by Wells Bloomfield for its products are SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS Resetting of safety thermostats, circuit breakers, over...
PARTS & SERVICE CUSTOMER SERVICE DATA Thank You for purchasing this Wells Bloomfield appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life.
TEMPERATURE CONTROL KNOB. The knob has a numeric scale, where higher numbers correspond to higher temperature. 3. On warmers equipped with an INDICATOR LIGHT, the light will glow when the thermostat is calling for heat (i.e. the element is energized).
Refer to the product nameplate for the specific appliance for agency listings. In general: This appliance conforms to NSF Standard 4 for sanitation only if installed in accordance with the supplied Installation Instructions. UL Listed warmers are Listed under UL File E6070. PRECAUTIONS AND GENERAL INFORMATION All servicing requiring access...
Voltage and phase must match the nameplate specifications. Plugging the warmer into the wrong voltage can severely damage the unit or cause noticeable decreased performance. 2. Your warmers is equipped with a grounded electrical cord. This cord must be plugging into a properly grounded electrical receptacle.
Always use an inset. DO NOT place food directly into the warmer. 2. Check water level in warmer frequently during use. Running warmers dry will lower the temperature of the food in the insert pan, and may damage the warmer. DO NOT allow dry operation of warmer.
CLEANING INSTRUCTIONS CAUTION SHOCK HAZARD Do NOT splash or pour water into or over any control panel or wiring. CAUTION: SHOCK HAZARD Disconnect warmer from electric power before cleaning CAUTION: BURN HAZARD Allow warmer to cool completely before cleaning. CAUTION: SHOCK HAZARD DO NOT submerge warmer in water.
Page 9
WEEKLY CLEANING INSTRUCTIONS PREPARATIONS: Remove any insets, pans and/or adapter tops. Drain or remove water from well if used for wet operation. FREQUENCY: Weekly, or whenever lime or scale is seen accumulating on the sides of the warmer pans. TOOLS: Commercial Delime Cleaner Plastic Scouring Pad Clean Cloth or Sponge...
TROUBLE SHOOTING SUGGESTIONS SYMPTOM No power to warmer Warmer will not heat Warmer trips circuit breaker Warmer slow to heat There are no user-serviceable components in this appliance. In all instances of damage or malfunction, contact your Authorized Wells Service Agency for repairs. POSSIBLE CAUSE Circuit breaker off or tripped Unit not plugged in...
Chlorides can attack the surface of stainless steel, resulting in corrosion and pitting. Keep your stainless steel warmers clean and free from calcium buildup. Use alkaline, alkaline chlorinated or non-chloride cleanser. Use citric acid-based cleaners to remove calcium deposits.
4 QT. ROUND INSET w/ lid 7 QT. ROUND INSET w/ lid 11 QT. ROUND INSET w/ lid 11 QT. ROUND INSET w/ hinged lid ADAPTER TOPS FOR HW-10 ONE 7 QT. INSET ADAPTER TOP ONE 4 QT. INSET ADAPTER TOP ADAPTER TOPS FOR HW/SMP TWO 7 QT.
For factory authorized service, or to order factory authorized replacement parts, contact your Wells authorized service agency, or call: Wells Bloomfield, LLC 2 Erik Circle P. O. Box 280 Verdi, NV 89439 Service Parts Dept. phone: (775) 689-5707 fax:...
Page 14
Commercial Food Equipment Service Association Wells Bloomfield proudly supports CFESA Commercial Food Equipment Service Association SERVICE TRAINING - QUALITY SERVICE SERVICE TRAINING - QUALITY SERVICE Genuine Parts Protect - YOU - All - Ways CUSTOMER SATISFACTION CUSTOMER SATISFACTION WELLS BLOOMFIELD, LLC 2 ERIK CIRCLE, P.