Table of Contents
Advertisement
Quick Links
NetVanta
Series
(with Serial Network Interface Module)
Quick Configuration Guide
Equipment Required
•
V.35 or X.21 cable for connecting the system to the existing network.
•
VT100 terminal or PC with VT100 emulation software.
•
DB-9 (male) to DB-9 (female) straight-through cable for configuring the unit.
Cable length for the serial interface should not exceed 25 feet.
This quick configuration guide provides step-by-step instructions for configuring
your application. The configuration scripts are available on the ADTRAN OS
Documentation CD.
Network Diagrams
Frame Relay Diagram
Branch Office
eth 0/1
LAN IP: 10.10.20.7 /24
PWR
PWR
STAT
STAT
NetVanta
PPP over Point-to-Point T1 Diagram
Branch Office
PWR
PWR
NetVanta
eth 0/1
LAN IP:
10.10.20.7 /24
64200866L1-42C
V.35 or X.21
TSU
TSU IQ
A
B
C
ENTER
1
2
3
D
E
F
4
5
6
NEXT
PREV
ADD
7
8
9
NetVanta 3200
VPN
VPN
WAN
WAN
LAN
LAN
SHIFT
DELETE
QUICK
CANCEL
*
0
#
TD
TD
RD
RD
TD
TD
RD
TD
RD
RD
FR 1.x
DLCI 16
Annex D Signaling
192.168.72.1 /30
V.35 or X.21
serial 1/1
TSU
Point-to-Point T1
TSU IQ
A
B
C
1
2
3
ENTER
D
E
F
4
5
6
NEXT
PREV
ADD
NetVanta 3200
7
8
9
VPN
VPN
WAN
WAN
LAN
LAN
SHIFT
DELETE
QUICK
STAT
STAT
TD
TD
RD
RD
TD
TD
RD
TD
RD
RD
CANCEL
*
0
#
PPP 1
PPP Signaling
192.168.72.1 /30
Technical Support 1-888-4ADTRAN (1-888-423-8726)
Corporate HQ
LAN IP: 10.10.10.1 /24
V.35 or X.21
TSU
TSU IQ
A
B
C
ENTER
1
2
3
D
E
F
4
5
6
NEXT
PREV
ADD
7
8
9
SHIFT
DELETE
QUICK
CANCEL
*
0
#
WAN IP: 192.168.72.2 /30
10.10.10.1 /24
LAN IP:
V.35 or X.21
TSU
TSU IQ
A
B
C
1
2
3
ENTER
D
E
F
4
5
6
NEXT
PREV
ADD
7
8
9
SHIFT
DELETE
QUICK
CANCEL
*
0
#
WAN IP: 192.168.72.2 /30
March 2005
Corporate HQ
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ADTRAN NetVanta Series
Summary of Contents for ADTRAN NetVanta Series
- Page 1 DB-9 (male) to DB-9 (female) straight-through cable for configuring the unit. Cable length for the serial interface should not exceed 25 feet. This quick configuration guide provides step-by-step instructions for configuring your application. The configuration scripts are available on the ADTRAN OS Documentation CD. Network Diagrams...
- Page 2 NetVanta. You must change the IP address of your PC before you can proceed. ADTRAN recommends that you set the Ethernet speed and duplex to match the switch or hub it is plugged in to. For example:...
- Page 3 The NetVanta Network Interface Modules (NIMs) use a slot/port notation for interface identification. All non-modular interfaces built into the base unit (e.g., the Ethernet port) are identified using 0 as the slot number. Configure the Serial Interface The following steps demonstrate configuring a serial network interface. 1.
- Page 4 Configure the Virtual PPP Interface The following steps show how to configure a PPP virtual interface (labeled 1) to the corporate router. Skip to Create the Cross-Connect below if you are using Frame Relay. 1. At the (config)# prompt, enter interface ppp 1 to create a PPP virtual interface labeled 1. 2.
- Page 5 Scenario 2: Configuration for Branch Office router in the diagram on page 1 (No Internet Access at Local Site) 1. At the (config)# prompt, enter ip route 0.0.0.0 0.0.0.0 ppp 1 (or frame-relay 1.16) to set up the default route. 2.
- Page 6 The Enable Security mode passwords are case sensitive. Configure Telnet Access The following steps show how to access the Telnet configuration parameters and change the password. The default password for initializing a Telnet session is password (all lowercase). For security purposes, change the password to something unique. For this example, replace the underlined word with a password of your choosing.
Need help?
Do you have a question about the NetVanta Series and is the answer not in the manual?
Questions and answers