Table of Contents
Advertisement
Quick Links
NetVanta
Series
(with Serial Network Interface Module)
Quick Configuration Guide
Equipment Required
•
V.35 or X.21 cable for connecting the system to the existing network.
•
VT100 terminal or PC with VT100 emulation software.
•
DB-9 (male) to DB-9 (female) straight-through cable for configuring the unit.
Cable length for the Serial interface should not exceed 25 feet.
This quick start guide provides step-by-step instructions for configuring your application. The
configuration scripts are available on the ADTRAN OS System Documentation CD.
Network Diagrams
Frame-Relay Diagram
Branch Office
eth 0/1
LAN IP: 10.10.20.7/24
PPP over Point-to-Point T1 Diagram
Branch Office
eth 0/1
LAN IP:
64200866L1-42A
V.35 or X.21
TSU
TSU IQ
A
B
C
ENTER
1
2
3
D
E
F
4
5
6
NEXT
PREV
ADD
7
8
9
NetVanta 3200
SHIFT
DELETE
QUICK
PWR
PWR
VPN
VPN
WAN
WAN
LAN
LAN
CANCEL
*
0
#
STAT
STAT
TD
TD
RD
RD
TD
TD
RD
TD
RD
RD
NetVanta
FR 1
DLCI 16
Annex D Signaling
192.168.72.1/30
V.35 or X.21
serial 1/1
TSU
Point-to-Point T1
TSU IQ
A
B
C
ENTER
1
2
3
D
E
F
4
5
6
NEXT
PREV
ADD
NetVanta 3200
7
8
9
VPN
VPN
WAN
WAN
LAN
LAN
PWR
PWR
SHIFT
DELETE
QUICK
STAT
STAT
TD
TD
RD
RD
TD
TD
RD
TD
RD
RD
CANCEL
*
0
#
NetVanta
PPP 1
PPP Signaling
10.10.20.7/24
192.168.72.1/30
Technical Support 1-888-4ADTRAN (1-888-423-8726)
Corporate HQ
LAN IP: 10.10.10.1/24
V.35 or X.21
TSU
TSU IQ
A
B
C
ENTER
1
2
3
D
E
F
4
5
6
NEXT
PREV
ADD
7
8
9
SHIFT
DELETE
QUICK
CANCEL
*
0
#
WAN IP: 192.168.72.2/30
Corporate HQ
10.10.10.1/24
LAN IP:
V.35 or X.21
TSU
TSU IQ
A
B
C
ENTER
1
2
3
D
E
F
4
5
6
NEXT
PREV
ADD
7
8
9
SHIFT
DELETE
QUICK
CANCEL
*
0
#
WAN IP: 192.168.72.2/30
February 2004
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ADTRAN NetVanta Series
Summary of Contents for ADTRAN NetVanta Series
- Page 1 DB-9 (male) to DB-9 (female) straight-through cable for configuring the unit. Cable length for the Serial interface should not exceed 25 feet. This quick start guide provides step-by-step instructions for configuring your application. The configuration scripts are available on the ADTRAN OS System Documentation CD. Network Diagrams Frame-Relay Diagram...
- Page 2 Configuring the Unit The NetVanta may be initially accessed and managed either via a console session or through a Telnet session. See step 1a for console session instructions. Initiating a Tel- net session requires using a hub and two Ethernet cables (one for the PC and one for the unit).
- Page 3 NetVanta. You must change the IP address of your PC before you can proceed. ADTRAN recommends that you set the Ethernet speed and duplex to match the switch or hub it is plugged in to. For example: (config-eth 0/1)#speed 10 (config-eth 0/1)#half-duplex 3.
- Page 4 Skip to step 6 for PPP configuration. Configuring the Frame-Relay Virtual Interface The following steps outline configuring a frame-relay virtual interface (labeled 1) using a single DLCI back to the corporate router (defined as DLCI 16). 1. At the (config)# prompt, enter interface fr 1 to create a frame-relay virtual interface labeled 1.
- Page 5 Creating the Cross-Connect 1. For frame-relay applications, at the (config)# prompt, enter cross-connect 1 serial 1/1 frame-relay 1 to connect the serial NIM to the virtual frame-relay interface (fr 1.16). 2. For PPP applications, enter cross-connect 1 serial 1/1 ppp 1 to connect the serial NIM to the virtual PPP interface labeled 1.
- Page 6 Configuring Telnet The following steps show how to access the Telnet configuration parameters and change the password. The default password for initializing a Telnet session is password (all lower-case). For security purposes, change the password to something unique. For this example, replace the underlined word with a password of your choosing.
Need help?
Do you have a question about the NetVanta Series and is the answer not in the manual?
Questions and answers