Table of Contents
Advertisement
Available languages
Available languages
6) In the standby mode, the button
ALARM can be used to switch alarms
1 and 2 on and off . Press the button
repeatedly until the setting desired has
been selected:
Setting
Indication on the
display
both alarms Off
no bell symbol
only alarm 1 On
bell symbol 1
only alarm 2 On
bell symbol 2
both alarms On
bell symbols 1 and 2
5 Control via the App UNDOK™
The app UNDOK™ allows you to operate
WAP-202RS by means of a smartphone
or a tablet computer . The app is availa-
ble for units with the operating system
"Android" or "iOS" and can be down-
loaded from the respective App Store
free of charge .
Notes:
1 . The app is provided by a third party and is
not covered by the warranty of MONACOR
INTERNATIONAL . In case of any problems,
please contact the supplier of the app!
2 . Due to further developments of the app, the
information provided in this chapter may
not be up to date .
1) Download and install the app on your
smartphone / tablet .
2) Open the app . The standard PIN to
access the app is "1234" . If the PIN
is changed, the new PIN must be en-
tered after the app has been opened .
To change the default PIN "1234", go
to the menu "System settings", call
up
Network
and then the menu item
NetRemote PIN Setup
. The following
menu will appear on the display:
NetRemote PIN Setup
1234
0123456789
BKSP
OK
CANCEL
Turn the knob CONTROL SELECT to
select the digits and the three fields
and then press the knob to confirm
(with the remote control: selection via
the arrow buttons; confirmation via
the button ENTER) .
BKSP
= to delete the last digit
= to confirm the PIN
OK
CANCEL
= to return to the previous
menu
3) The start page of the app provides
an overview of the units available .
WAP-202RS is listed with its "friendly
name" (= name of the unit in the net-
work):
☞
in the menu "System
Info
settings" .
If the unit is not shown in the list,
check the network settings and, if re-
quired, set up the unit again . As an
alternative, you can try to integrate
the unit into the network by means of
the setup wizard of the app ("Set up
audio system") . In case of problems,
also observe the notes in the box at
the end of chapter 5 .1 .2 .
4) To operate the unit, tap its name:
The control page for the unit will be
opened . The user interface of the
page is self-explanatory and intui-
tive . "SOURCE", for example, is used
to select the operating mode and
"BROWSE" to choose one of the op-
tions available for the mode selected .
In the radio mode, the storage loca-
tions will be shown when the icon
is tapped: The current station can
be saved (tap the plus sign after the
storage location number) and called
up again . "NOW PLAYING" will show
all information concerning the current
replay . Setting options for the app and
the unit can be called up via the icon
or
(depending on the app version)
to be found in the upper bar of the
screen .
5) To return to the overview, tap the
arrow in the upper bar of the screen .
5.1 Multi-room mode
If there are multiple units WAP-202RS in
the network, a multi-room system can
be established . In a multi-room system,
units can be combined as groups for
synchronous replay of the same audio
material . The replay source is defined
by the master (server) of the group and
will be adopted by the other units of the
group (clients) . A group can include up
to 5 units (1 server and a maximum of
4 clients) .
Notes:
1 . Each unit can only be included in one group
Fig. 51
(either as a server or as a client) .
2 . To make sure that the server / client assign-
ment currently defined will remain saved,
never switch off the server of the group by
means of the switch POWER .
5.1.1 Multiroom settings via the app
Note: The icons may vary according to the
app version used .
1) To create a group: In the overview,
multi-room enabled units are indicated
by the icon
select the unit to be used as the server
of the group, tap the corresponding
icon . A window for group creation
will appear . The units available in the
network are shown; to add a unit as a
2) To edit a group: Tap the icon
3) To operate a group: Tap the group
5.1.2 Multiroom settings at the unit
The multi-room mode can also be
used without the app UNDOK . In the
menu "System settings" (chapter 3 .4),
under
ting / display options are available:
View details
Create new g roup
Add to g roup
List current clients
Leave g roup
–
–
after their name . To
client to the group, tap the field next
to its name (check mark in field) . If
required, assign a user-defined name
to the group . Tap "OK" to confirm the
creation of the group . The group will
then be shown in the overview .
the group name and then edit the
group as desired: To add a unit to the
group or to remove it, tap the field
next to its name; a group can be re-
named or removed (= dissolved) .
name: The control page for the group
will be opened . A group can be op-
erated like a single unit, the only dif-
ference being that the source is only
selected for the server .
By means of a slider, the volume
for all group members can be ad-
justed at the same time . To mute the
group, tap the speaker icon to the left
of the slider . To make settings sepa-
rately for individual group members,
click the multi-speaker icon to the
right of the slider; a new page will be
opened where you can mute individ-
ual group members and adjust their
volume . In addition, it is also possible
to make individual equalizer settings
separately (tap the corresponding
equalizer icon) .
, the following set-
Multiroom
Multiroom
>
>
>
>
>
Fig. 52
: To view the status of
View details
the unit (not grouped, server, client)
and, if the unit is member of a group,
the name of the group .
Create new g roup
: To create a new
group with the unit as the server .
A menu will appear; enter and confirm
the desired name of the group (op-
eration of the input menu:
ter 3 .3, fig . 17) . Then the unit will
show a list of the units available .
Select the client desired from the list
and then press the knob CONTROL
SELECT to confirm . A client added to
the group will be marked by an as-
terisk
. If you do not want to add
*
further clients, press the button BACK
to exit the menu .
after
☞
chap-
29
Advertisement
Table of Contents
