Table of Contents
Advertisement
5.3.5
Update the TV software
1. Turn the TV on and wait for it to boot completely.
2. Insert the USB memory stick that contains the software
update files in one of the TV's USB ports.
3. The TV will detect the USB memory stick automatically.
Then a window jumps out as
Note: If the USB flash drive is not detected after power up,
disconnect it and re-insert it.
4. Select [Update] and press OK. See
5. To proceed, In next menu select [Start] and press OK to
start software updates. See
6. Upgrading will now begins and the status of the updating
progress will be displayed.
7. When the TV software is updated. Remove your USB flash
drive, then select [Restart] and press OK to restart the
TV.See
Figure
5-4.
Figure 5-2 Update the TV software [1/3]
Figure 5-3 Update the TV software [2/3]
Figure 5-4 Update the TV software [3/3]
Note:
Service Modes, Error Codes, and Fault Finding
Figure
5-2.
Figure
5-2.
Figure
5-3.
19080_207_110324.eps
110324
19080_208_110324.eps
110324
19080_209_110324.eps
110324
•
Do not remove the USB flash drive during the software
update.
•
If a power failure occurs during the update, do not remove
the USB flash drive from the TV. The TV will continue the
software update as soon as the power comes up again.
•
If an error occurs during the update retry the procedure or
contact the dealer.
•
We do not recommend downgrading to an older version.
•
Once the upgrade is finished, use the PC to remove the TV
software from the USB portable memory.
5.3.6
Content and Usage of the One-Zip Software File
Below you find a content explanation of the One-Zip file, and
instructions on how and when to use it. Only files that are
relevant for Service are mentioned here.
•
EDID_clustername.zip: Contains the EDID content of the
different EDID NVMs.
•
FUS_clustername_version.zip: Contains the file
downloaded which is needed to upgrade the TV main
software and the software download application.
•
NVM_clustername_version.zip: Default NVM content.
5.3.7
How to Copy NVM Data to/from USB
When copying data to and from a USB memory stick, the folder
"repair" is used. When inserting an empty USB memory stick,
and downloading data to the stick, the TV will create this folder.
When sending data from a USB memory stick to a TV, the
intended data must be available in the "repair" folder.
Note that when copying EDID data to the TV, all necessary
EDID files must be in this folder.
Service mode overview for your reference.
Table 5-3 Service mode overview
Service Modes
SAM
Factory Mode
CSM
USB SW upgradeable SW-upgrading of flash memories MT5561 can be done
NVM-Editor in SAM
Service Data
USB copy/paste in
SAM
UART logging
Blind SAM
Clear Buffer
5.4
Error Codes
5.4.1
Introduction
Error codes are required to indicate failures in the TV set. In
principle a unique error code is available for every:
•
Activated (SW) protection.
2
•
Failing I
C device.
2
•
General I
C error.
The last five errors, stored in the NVM, are shown in the
Service menu's. This is called the error buffer.
The error code buffer contains all errors detected since the last
time the buffer was erased. The buffer is written from left to
right. When an error occurs that is not yet in the error code
buffer, it is displayed at the left side and all other errors shift one
position to the right.
An error will be added to the buffer if this error differs from any
error in the buffer. The last found error is displayed on the left.
back to
div.table
TPM16.4L LA
5.
Description
Service alignment mode
Used for extended alignments
3-page compact CSM pages. There will be CSM dump to
USB-stick upon entering CSM-mode
via USB. The main SW can be upgraded via the ZIP file
downloaded.
NVM-editor will function as in the past: Address and Value
field is a decimal value via digit entry
New Service data in SAM for CTN, Prod. no., 12NC
programming with virtual keyboard
Channel list, NVM data, Readable info, EDID
There will be printout available in UART. No specifications
of the printout, per MTK provision/definition.
RC sequence "062598" + "Menu" +
"Panel code"
RC sequence "062599" + "OK" or via SAM
EN 19
2016-Apr-1
Advertisement
Table of Contents
