Telguard TG-7 Series Quick Installation Manual

INCOMING
TELCO
4 5
3 6
R T
2 7
Acceptable RSSI Range
1 8
RJ31X
ANTENNA
Battery wire should
be at least ¼ inch
apart from AC wires
WARNING:
HIGH VOLTAGE
PRESENT ON PHONE
LINES.
System Status
DISCONNECT PRIOR
LEDs
TO SERVICING.
Power LED
LED Mode
Toggle Button
SIM
TELGUARD
Digital TG-7
R
Battery
Connector
STC2
(N.C.)
STC1
(N.O.)
T
1 2 1 2 3 4 5 6 1 2 3 1 2
-
+
Optional
Battery
CAUTION:
INCORRECT
CONNECTIONS MAY RESULT
IN DAMAGE TO UNIT.
www.Telguard.com
REFER TO INSTALLATION AND
OPERATING INSTRUCTIONS
MANUAL. THIS DEVICE COMPLIES
WITH FCC RULE PART 15.
System Status LEDs (RSSI Mode)
OFF
BLINKING
ON
RSSI (bars) NONE 1 1½ 2 2½ 3 3½
NO
Signal (dBm) < -110 > -110 > -100 > -90 > -80 > -70
SVC
System Status LEDs (Normal Mode)
OFF NOT ACTIVATED
ACTIVATION ON ACTIVATED
FLASHING ACTIVATION DENIED
OFF NO TROUBLE
FLASHING TROUBLE:
1 FLASH = AC LOW/MISSING
2 FLASH = LBC LOW BATTERY
SYSTEM
3 FLASH = LFC LINE FAULT
TROUBLE
4 FLASH = NSC NO SERVICE
5 FLASH = RFC RADIO FAILURE
6 FLASH = DTF DIAL TONE FAIL
7 FLASH = PPF PNL PRES FAIL
OFF
PANEL ON-HOOK (PRIMARY)
PANEL COMM
ON PANEL ON-HOOK (BACKUP)
FLASHING PANEL OFF-HOOK
1
2
OFF IDLE
3
4 WAITING FOR RESPONSE
TMC COMM ON
FROM TMC
5
FLASHING ACTIVATION DENIED
OFF IDLE
RADIO STATUS
ON RADIO INITIALIZING
FLASHING RADIO COMMUNICATING
FLASHING LINK SUPERVISION ENABLED
(2 FLASHES EVERY 6 SECONDS)
NOT USED OFF NOT USED
NOT ACTIVATED OR
OFF
RESTORED
TRIP INPUT
ON ACTIVATED
OFF AC NOT CONNECTED TO UNIT
POWER LED
ON AC CONNECTED TO UNIT
Alarm Panel
EARTH
GROUND
AC
(12V 800MA)
TO EXTERNAL
TRIP INPUT
Telguard TG-7 Series
QUICK INSTALLATION GUIDE [BACKUP MODE]
NOTE: If a TG-PEM Power and Expansion Module accessory is part of your installation, refer to the
full Installation and Operation Guide available from www.telguard.com/7install.
Installation Summary
There are seven steps in installing Telguard properly. IF YOU DO NOT
4
PROCEED IN THE ORDER AND MANNER PRESCRIBED, YOU MAY
> -60
NOT COMPLETE THE INSTALLATION IN THE TIME ALLOCATED.
S 1: R
TEP EGISTER FOR
The registration form may be completed online through our 24/7 dealer portal
www.telguard.com.
S 2: L U
TEP OCATE NIT AND
First, you will be confirming that Telguard has adequate cellular signal strength. Press the
LED/RSSI Mode Toggle button one time, LEDs will now indicate signal strength. Minimum
recommended is 2 (2 on solid). Press the LED/RSSI Mode Toggle button a second time to exit
RSSI mode.
S 3: T
TEP RANSMIT
Next, you will verify that the alarm panel is programmed properly. This step is important to verify
that the alarm panel is programmed with valid account code and central station information
before transmitting signals through the cellular network.
S 4: P , A
TEP ROGRAM
C R N
ELLULAR ADIO
Next, you will be connecting the alarm panel's digital dialer output to Telguard and verifying that
alarm signals can be reliably sent through Telguard over cellular to the central station digital
receiver. The incoming Telco line is not connected to Telguard during this step. A minimum of
two alarm signals must be transmitted. Activation is confirmed when LED 1 is illuminated.
(NOTE:
THE FIRST ALARM WILL ACTIVATE THE UNIT AT THE
C ,
ENTER IT WILL NOT GO TO THE
C S
SENT TO THE ENTRAL
S 5: C S
TEP ONNECT
Next, you will wire Telguard's supervisory trip outputs to the alarm panel and then test.
S 6: C T
TEP ONNECT
Optionally, you can wire an external relay input to the trip input lead and ground, and test.
S 7: C
TEP OMPLETE THE
Your last step will be to attach earth ground, reconnect Telco, and permanently mount the unit.
ULC Note: To maintain compliance in Canada, the radio frequency warning
label (supplied) must be affixed to the cover of the TG-7 series device.
C S
ELLULAR ERVICE
M S S
EASURE IGNAL TRENGTH
P A T
ANEL LARMS OVER THE ELCO
& T P
CTIVATE RANSMIT ANEL
ETWORK
T
ELGUARD
C S ,
ENTRAL TATION ALL SIGNALS AFTER THE FIRST ARE
)
TATION
T O
UPERVISORY RIP UTPUTS
I ( )
RIP NPUT OPTIONAL
I
NSTALLATION
(RSSI)
C
ONNECTION
A
LARMS OVER THE
C
OMMUNICATION