Related Manuals for Teledyne TIENet 301
Summary of Contents for Teledyne TIENet 301
- Page 1 TIENet ® pH/Temperature Device Installation and Operation Guide ® Manual Body #69-4303-071 Copyright © 2021. All rights reserved, Teledyne ISCO Revision E, May 2021...
- Page 3 Teledyne Isco recommends that you read this manual completely before placing the equipment in service. Although Teledyne Isco designs reliability into all equipment, there is always the possibility of a malfunction. This manual may help in diagnosing and repairing the malfunction.
- Page 5 TIENet™ 301 pH/Temperature Device Safety TIENet™ 301 pH/Temperature Device Safety Before installing, operating, or maintaining this equipment, it is General Warnings imperative that all hazards and preventive measures are fully understood. While specific hazards may vary according to location and application, take heed of the following general warnings: WARNING Avoid hazardous practices! If you use this instrument in...
- Page 6 TIENet™ 301 pH/Temperature Device Safety The equipment and this manual use symbols used to warn of Hazard Symbols hazards. The symbols are explained below. Hazard Symbols Warnings and Cautions The exclamation point within the triangle is a warning sign alerting you of important instructions in the instrument’s technical reference manual.
-
Page 7: Table Of Contents
1.4.1 TIENet 301 Device ........ - Page 8 TIENet® 301 pH/Temperature Device Table of Contents...
-
Page 9: Section 1 Introduction
The TIENet Model 301 pH/temperature sensing device transmits acidity/alkalinity data to the Signature® flow meter using Teledyne ISCO’s TIENet connectivity. The 301 device consists of a wall-mountable isolated interface with a 10 or 23m cable, that attaches to the flow meter. Attached to the device is a stainless steel, submersible probe with combi- nation-type electrodes. -
Page 10: Operation
TIENet® 301 pH/Temperature Device Section 1 Introduction For greater distances, external connection via conduit, and con- nection of additional TIENet devices, the TIENet Expansion Box is available. Bulk TIENet cable may also be used for greater dis- tances. The maximum distance between the 301 and the flow meter is 1,000 ft. -
Page 11: Technical Specifications
1.3 Technical Specifications Table 1-1 Technical Specifications TIENet 301 Device 301 Weight (w/o sensor) w/ 10m cable: 3.5 lb -20 to 50 °C (-4 to 122 °F) Ambient Operating Temperature... - Page 12 TIENet® 301 pH/Temperature Device Section 1 Introduction 1.4 Replacement Parts Parts and accessories can be purchased by contacting Teledyne ISCO’s Customer Service Department. and Accessories Teledyne ISCO Customer Service Dept. P.O. Box 82531 Lincoln, NE 68501 USA Phone: 800 228-4373...
-
Page 13: Section 2 Installation And Setup For Signature
TIENet 301 pH/Temperature Device ® Section 2 Installation and Setup for Signature 2.1 Installation External TIENet devices such as the 301 are all electrically con- nected to the Signature flow meter in the same manner, usually using conduit or cord-grip cable fittings. Multiple external TIENet devices can be connected simultaneously. - Page 14 TIENet® 301 pH/Temperature Device Section 2 Installation and Setup for Signature 2. If using a cord-grip fitting, install the cable nut in the appropriate opening on the bottom of the Signature enclo- sure, securing it to the wall with the lock nut (concave side facing wall).
-
Page 15: Tienet Device Terminal Connections
TIENet® 301 pH/Temperature Device Section 2 Installation and Setup for Signature Shield Braid-Drain Figure 2-3 TIENet Device terminal connections Figure 2-4 Attach wired terminal strip to case board socket... - Page 16 TIENet® 301 pH/Temperature Device Section 2 Installation and Setup for Signature Figure 2-5 Position and secure the cable 5. Gently tug the cable downward, to remove any slack within the enclosure, taking care not to put any stress on the con- nection.
-
Page 17: Connecting To Signature Portable Via A Tienet Receptacle
TIENet® 301 pH/Temperature Device Section 2 Installation and Setup for Signature The optional external TIENet devices compatible with the Sig- 2.1.2 Connecting to nature Portable (and Signature) all scan into the hardware in the Signature Portable via same manner. A scan is required anytime a new TIENet device is a TIENet Receptacle added. -
Page 18: Ph Probe Installation Considerations
TIENet® 301 pH/Temperature Device Section 2 Installation and Setup for Signature Install the probe only in streams that have continuous flow. The 2.1.3 pH Probe Installation sensing end of the probe must always remain wet. For proper Considerations operation, there must be enough flow to submerge the sensing end of the probe completely. -
Page 19: Configuring The 301
2.2 Configuring the 301 To configure the Signature flow meter for operation with a pH probe using the TIENet 301 device, press ) to access MENU the top menu, and select Hardware Setup. For all TIENet devices... -
Page 20: Updating The Device List
TIENet® 301 pH/Temperature Device Section 2 Installation and Setup for Signature When the 301 is physically added to the system, select Perform 2.2.1 Updating the Device Scan so that the flow meter detects it. When the scan is complete, List the 301 appears in the list of connected devices, ready to be con- figured with the steps shown in Figure 2-9 on the following page. - Page 21 TIENet® 301 pH/Temperature Device Section 2 Installation and Setup for Signature Select Operation 1. Hardware Setup 2. Configure 3. Administration 4. Home Hardware Setup 1. Smart Sensor Setup (TIENet) 2. SDI-12 Setup 3. MODBUS Input Setup 4. MODBUS Output Setup 5.
-
Page 22: Ph Probe Life
Calibration intervals typically range from weekly to monthly, depending on the application. Note For pH probe calibration, Teledyne ISCO recommends that you use a glass container for the buffer solutions, and ensure that the following conditions are met:... - Page 23 TIENet® 301 pH/Temperature Device Section 2 Installation and Setup for Signature Configure Options 1. Site Setup 5. Data Storage/Push Setup 2. Measurement Setup 6. Sampler Setup 3. Adjust 7. Inputs/Outputs/Alarms Setup 4. Equation/Trigger Setup 8. Reset Totalizers 9. Reports/History Setup Adjust Options Perform pH Calibration of sensor Level...
-
Page 24: Firmware Updates
If none of these solutions work, it may be necessary to replace the probe. 2.7 Contact Teledyne If you have further questions about the installation, operation, and maintenance of your TIENet device, please contact our... -
Page 25: Appendix A Replacement Parts
Replacement parts are called out in the following illustrations. Refer to the call-out in the adjacent table to determine the part number for the item. Replacement parts can be purchased by contacting Teledyne ISCO’s Customer Service Department. Teledyne ISCO Customer Service Department P.O. -
Page 26: 301 Ph Temperature
TIENet® 301 pH/Temperature Device A.1.1 301 pH Temperature REPLACEMENT PLUG SENSOR CAP KIT FOR 2100 SERIES AND TIENET DEVICES SKU: 609004469... - Page 27 Compliance Statements Name and amount of Hazardous Substances or Elements in the product Hazardous Substances or Elements Component Name (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) Circuit Boards Display Wiring Internal Cables DC Motor Connectors Battery Solenoid valve Name and amount of Hazardous Substances or Elements in the product O: Represent the concentration of the hazardous substance in this component’s any homogeneous pieces is lower than the ST/ standard limitation.
- Page 29 68504, U.S.A. customer’s facility and the repair facility. * This warranty applies to the USA and countries where Teledyne Isco does not have an authorized dealer. Customers in countries outside the USA, where Teledyne Isco has an authorized dealer, should contact their Teledyne Isco dealer for warranty service.