Mytee Spyder HP60 User Manual
Hide thumbs
Also See for Spyder HP60:
- Instructions manual (21 pages) ,
- Instruction manual (11 pages) ,
- User manual (15 pages)
Related Manuals for Mytee Spyder HP60
Summary of Contents for Mytee Spyder HP60
- Page 1 User Manual Spyder Model: ™ HP60 REV. 6/4/21 13655 Stowe Dr. Poway, CA 92064 P: (858) 679-1191 F: (858) 726-6005 www.mytee.com...
- Page 2 Congratulations on the purchase of your new Spyder™ Automotive Detailing Extractor. As technology continues to develop you can work confidently knowing that both Mytee and its employees are equally dedicated to developing with the industry and its advances. Like any other piece of machinery or technology, the Spyder™ also requires proper maintenance and care to keep the product working over extended use.
-
Page 3: Table Of Contents
Table of Contents Important Safety Information At a Glance 1.1 - Technical Specifications 1.2 - Included with the Spyder™ 1.3 - Spyder™ Front View 1.4 - Spyder™ Rear View Machine Operation 2.1 - Powering the Spyder™ 2.2 - Filling the Solution Tank 2.3 - Connecting the Hoses 2.4 - Operating the Spyder™... -
Page 4: Important Safety Information
When and if calling This machine must be grounded. If it should malfunction or Mytee for support, please have your Model and Serial Number break down, grounding provides a path of least resistance for available for faster assistance. - Page 5 Important Safety Information To reduce the risk of fire, electrical shock, or injury: may contain: chemicals, grease, oil, acid, alkalies, or other dangerous liquids. 1. Read all instructions before using equipment. 18. Do not leave operating unattended. Use only as described in this manual. Use only manufacturer’s recommended attachments.
-
Page 6: At A Glance
1 - At a Glance 1.1 - Technical Specifications Solution Tank 5 gallon capacity (approx.) Recovery Tank 5 gallon capacity Single 3-stage low amp Vacuum Motor 100 CFM, 130” water lift 120 PSI diaphragm pump Pump 1.3 GPM 1,200W REAL HEAT™ system Heater 210º... -
Page 7: Spyder™ Front View
1 - At a Glance 1.3 - Spyder™ Front View 1. Clear recovery tank lid 6. Locking casters 2. Switch plate 7. Power cord 3. Solution tank lid 8. Cuff-Lynx™ vacuum hose connection 4. Solution tank 9. Recovery tank 5. Solution line connection... -
Page 8: Spyder™ Rear View
1 - At a Glance 1.4 - Spyder™ Rear View 1. Handle 3. Rear body bracket screws 2. Drain valve with 45º drain spout... -
Page 9: Machine Operation
2 - Machine Operation 2.1 - Powering the Spyder™ 2.4 - Operating the Spyder™ Plug the power cord from the Spyder™ into a standard grounded wall outlet. The Spyder™ operates off a single, ♦ grounded 20 amp outlet. 2.2 - Filling the Solution Tank In order to avoid vapor locking the unit, the components should be switched on by following the procedure below after a cleaning tool is connected:... -
Page 10: Emptying The Tanks
2 - Machine Operation 2.5 - Emptying the Tanks Empty the recovery tank via the drain valve on the rear of the machine. Make sure there is a bucket in place under the valve or the machine is in a position so the dirty water is drained safely. -
Page 11: Machine Maintenance
The Spyder™ has a small filter at the top of the vacuum stack in the recovery tank. This filter should be checked after each ♦ use. 3.3 - System Maintainer Regular flushing of the solution system with Mytee System Maintainer keeps your extractor running efficiently by removing... -
Page 12: Troubleshooting
Circuit breaker tripped in building. Reset breaker in building. turning on. Faulty switch or power cord. Contact a Mytee Service Center. Unclog the jet by removing and soaking in a vinegar Jet is clogged. and water solution. Scrub with a soft brush. Repeat if Poor solution flow. - Page 13 NOTES...
- Page 14 Mytee, LLC 13655 Stowe Dr. Poway, CA 92064 www.mytee.com © 2021 Mytee, LLC...