Subscribe to Our Youtube Channel
Related Manuals for Mytee Speedster 1000HV
Summary of Contents for Mytee Speedster 1000HV
- Page 1 Speedster Extractor Model Numbers: No Heater: 1000HV 1000HV-200 1005HV Heater: 1001HV 1001HV-200 1003HV 1006HV User and Parts Manual www.mytee.com...
-
Page 2: Table Of Contents
DAILY MAINTENANCE WEEKLY MAINTENANCE STORING MACHINE TROUBLESHOOTING REPLACEMENT PARTS ELECTRICAL DIAGRAMS DWG 1 of 5 ASSEMBLY PARTS LIST DWG 2 of 5 (Assembly) DWG 3 of 5 (Vac Tank) DWG 4 of 5 (Sol Tank) DWG 5 of 5 (Base) www.mytee.com... -
Page 3: Safety Precautions
♦ ♦ ♦ ♦ Do not handle plug with wet hands. ♦ ♦ ♦ ♦ Keep cord away from heated surfaces. ♦ ♦ ♦ ♦ Report machine damage or faulty operation immediately to your distributor. ♦ ♦ ♦ ♦ Follow mixing and handling instructions on chemical containers. www.mytee.com... -
Page 4: Safety Labels
Flammable materials or reactive metals can cause explosion or fire. WARNING LABEL- Located on back. Label warns operator of safe practices of equipment MACHINE COMPONENTS 1. Recovery Tank 2. Solution Tank 3. Motor housing/ Base www.mytee.com... -
Page 5: Pre-Operation
Do not use flammable solutions or materials in tank(s). FOR SAFETY: When using machine, follow mixing and handling instructions on chemical 5. Attach vacuum hose to recovery tank. containers. ATTENTION: If using powdered cleaning chemicals, mix prior to adding. www.mytee.com... - Page 6 A. Turn pump switch on. Pump **NOTE STEP 9 IS FOR 1000 AND 1001** B. Pull up on power prime lever for 30 9. Turning machine on: seconds. This will prime the pump. A. Turn pump switch on. Pump www.mytee.com...
-
Page 7: While Operating
DRAINING RECOVERY TANK E. Begin cleaning FOR SAFETY: When servicing machine, unplug cord from wall outlet. 1. Turn machine off and unplug power cord. NOTE: When cleaning upholstery, always check cleaning instructions sewn in furniture by manufacturer www.mytee.com... -
Page 8: Machine Maintenance
3. Clean machine with an all purpose cleaner and damp cloth. WEEKLY MAINTENANCE (EVERY 20 HOURS OF OPERATION) 1. Flush solution system with Mytee system maintainer to dissolve normal chemical buildup. Pour 7.5L (2 gal) of hot water 60°C (140°F) into solution tank. Add Mytee system... -
Page 9: Storing Machine
Remove filters and rinse clean with water. PROBLEM: Heater is blocked with hard water deposits. SOLUTION: Flush out heaters with system maintainers. If they are still blocked, replace heaters. PROBLEM: Brass check valve is stuck. SOLUTION: Replace with new check valve. www.mytee.com... - Page 10 Use a low foaming detergent. PROBLEM: Floor wand or is clogged with hair, carpet fibers and or debris. SOLUTION: Clean floor wand. PROBLEM: Ball float is not installed correctly. SOLUTION: Make sure that ball float is firmly installed on the elbow. www.mytee.com...
- Page 11 3 stage 115v 000-150 Vacuum motor 000-100 C301 2 stage, 115v 000-101 Vacuum motor 000-120 C301 2 stage high 000-110 performance 115v 000-100 Pump, 100 psi 000-101 C305 000-110 000-150 Pump, 250 psi 000-130 C322 000-140 Pump, 1200 psi 000-120 C359A www.mytee.com...
- Page 12 Male ¼” 000-130 000-110 000-140 000-150 Element heater 000-110 E571 600 watt 000-140 000-150 000-100 Switch, 2 position 000-120 E592 000-130 000-110 000-140 000-150 System maintainer, Maintains all 150-006 12 quarts per case internal hose lines & inline heaters www.mytee.com...
- Page 13 E573 000-140 210° auto 000-150 000-110 Thermostat sensor 000-140 E574 0009-150 375° manual Pump out, 115v 000-120 C381 000-120 Controller, separate 000-130 E564 circuit indicator 000-110 000-140 Switch, water level 000-120 E626 float 000-110 Brass check valve B108 000-150 www.mytee.com...
- Page 14 Speedster www.mytee.com...
Need help?
Do you have a question about the Speedster 1000HV and is the answer not in the manual?
Questions and answers