Table of Contents
Advertisement
Quick Links
PLA
Basic Characteristics Data
Model
Circuit method
Active fi lter
PLA100F
Flyback converter
Active fi lter
PLA150F
Flyback converter
Active fi lter
PLA300F
Forward converter
Active fi lter
PLA600F
Forward converter
*1
The value of input current is at ACIN 100V and 90% load.
*2
Burst mode frequency is changed by the used condition. Please contact us about detail.
*3
Available by option -W. Please refer to instruction manual "5. Option and Others".
PLA-10
Basic Characteristics Data
Switching
Input
frequency
current
*1
[kHz]
[A]
40 to 160
1.2
*2
20 to 150
40 to 160
1.7
*2
20 to 150
60
3.4
140
60
6.7
220
Inrush
Rated
current
protection
input fuse
Material
circuit
250V 3.15A Thermistor
CEM-3
250V 4A
Thermistor
CEM-3
250V 10A
Thermistor
CEM-3
250V 16A
SCR
FR-4
Series/Parallel
PCB/Pattern
operation availability
Single
Double
Series
sided
sided
operation
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Parallel
operation
No
No
No
*3
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Cosel PLA100F
Summary of Contents for Cosel PLA100F
- Page 1 Double Series Parallel Material [kHz] circuit sided sided operation operation Active fi lter 40 to 160 PLA100F 250V 3.15A Thermistor CEM-3 Flyback converter 20 to 150 Active fi lter 40 to 160 PLA150F 250V 4A Thermistor CEM-3 Flyback converter 20 to 150 Active fi...
-
Page 2: Table Of Contents
Instruction Manual AC-DC Power Supplies Enclosed type Function PLA-12 PLA-12 Input Voltage Range PLA-12 Inrush Current Limiting PLA-12 Overcurrent Protection PLA-12 Overvoltage Protection PLA-12 Thermal Protection PLA-13 Output Ripple and Ripple Noise PLA-13 Output Voltage Adjustment PLA-13 Isolation PLA-13 Low Power Consumption PLA-13 1.10 Remote ON/OFF PLA-13... -
Page 3: Function
¿ PLA100F, PLA150F ¡ If you need to use a switch on the input side, please select one that can withstand an input inrush current. ¡ PLA100F and PLA150F do not have thermal protection. ¿ PLA100F, PLA150F, PLA300F ¿ PLA300F, PLA600F ¡... -
Page 4: Output Voltage Adjustment Pla-13
Fig.2.1 Examples of connecting in series operation 1.9 Low Power Consumption ¿ PLA100F, PLA150F ¡ Low power consumption function is built-in in PLA100F and PLA150F. (No load power consumption: 1.5W typ) ¡ In 0 to 30% load, switching power loss is reduced by burst operation. -
Page 5: Assembling And Installation Method
30mm current of a power supply. Vent hole side [ the rated current value ¿ PLA100F, PLA150F, PLA300F ¡ Parallel operation is not possible. Not available Terminal block ¿ PLA600F ¡ Available by option -W. Please refer to instruction manual “5. Op- tion and Others”. - Page 6 2Convection (B, C mount) 3Forced air (0.5m / min Ambient temperature Fig.3.4 Ambient temperature derating curve for PLA100F/150F-24, -36, -48 [AC V] Fig.3.2 Input voltage derating curve Ambient temperature should be measured in 5 to 10cm from power supply to avoid own heat-up. About detail of ambient tem- ¡...
-
Page 7: Expected Life And Warranty Pla-16
FG terminal is connected to safety ground of the unit. Temperature of measurement point [C] Fig.3.7 Expected lifetime of fan 5 Option and Others 5.1 Outline of Options ¿ -C (PLA100F, PLA150F, PLA300F, PLA600F) -Option -C units have coated internal PCB for better moisture resistance. PLA-16... - Page 8 . -Operation stop voltage of Option -U units is set at a lower value ¡ PLA100F, PLA150F, PLA300F Remote on/off control. than that of a standard version to support low input voltage. -Use Conditions (Conditions of SEMI F-47 compliant) -Connector is added.
- Page 9 Instruction Manual AC-DC Power Supplies Enclosed type ¿ -W (PLA600F only) Table 5.3 Mating connectors and terminals on CN4 Connector Housing Terminal -Remote sensing, low output voltage alarm (LV alarm) and paral- BXH-001T-P0.6 lel operation function are built-in to this model. B2B-XH-AM XHP-2 J.S.T.
- Page 10 Instruction Manual AC-DC Power Supplies Enclosed type - When the output current is less than 10% of rated output current, Table 5.10 LV alarm operating conditions the output voltage fl uctuates occasionally. The minimum current Alarm Output of alarm If the output voltage drops below Open collector method is different depending on the model and the number of parallel the rating, the alarm signal is out-...
- Page 11 Load Fig.5.12 When using remote sensing function ¿ -T (PLA100F, PLA150F) Fig.5.15 Example of option -J (PLA100F) -Option -T units have vertically positioned screws on a terminal block. Table 5.11 Mating connectors and terminals on CN1 and CN2 in option -J -Please contact us for details about appearance.
- Page 12 -Please contact us for details about appearance. -Option -N1 units has its own vibration and shock specifi cation. Please contact us for details. -Please contact us for about safety approvals. Fig.5.18 Power supply installed on a DIN rail (PLA100F) PLA-21...
Need help?
Do you have a question about the PLA100F and is the answer not in the manual?
Questions and answers