Table of Contents
Advertisement
Quick Links
Basic Characteristics Data
Model
Circuit method
Active filter
PCA600F
Buck converter
Full - bridge converter
*
The value of input current is at ACIN 100VAC and rated load.
PCA-6
Basic Characteristics Data
Switching
Input
frequency
current
[kHz]
[A]
15 - 400
88
7.3
44
Inrush
Rated
current
protection
input fuse
Material
circuit
250V 16A
Relay
FR-4
Series/Parallel
PCB/Pattern
operation availability
Single
Double
Series
sided
sided
operation
-
Yes
Yes
Parallel
operation
Yes
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Cosel PCA600F
Summary of Contents for Cosel PCA600F
- Page 1 Single Double Series Parallel Material [kHz] circuit sided sided operation operation Active filter 15 - 400 PCA600F Buck converter 250V 16A Relay FR-4 Full - bridge converter The value of input current is at ACIN 100VAC and rated load. PCA-6...
-
Page 2: Series/Parallel Operation
Instruction Manual AC-DC Power Supplies Enclosed Type Terminal Blocks PCA-8 Wiring Input / Output Pin PCA-9 Wiring input pin PCA-9 Wiring output pin PCA-9 Output side attaching externally condenser PCA-9 Connection to pulse load PCA-9 Functions PCA-10 Input Voltage Range PCA-10 Inrush Current Limiting PCA-10... -
Page 3: Terminal Blocks
Table 1.1 Pin Configuration and Functions of CN1, CN2 1 Terminal Blocks Ground Pin No. Function level +Remote sensing N.C. No connection ¿ PCA600F N.C. No connection -Remote sensing å 6 7 8 VTRM Adjustment of output voltage Common ground (for signal) - Page 4 - When ambient temperature is 70 ª , point A is 75 ª or less ( The ambient temperature 40 ª to 70 ª should be not more than the calculated value by linear interpolation) In the case of PCA600F-12,-15,-24 -P2 Bad example Good example Input condition: Vin=85 to 170VAC Fig.2.3.
-
Page 5: Overvoltage Protection
Instruction Manual AC-DC Power Supplies Enclosed Type 3.4 Overvoltage Protection Output current of power supply ¡ An overvoltage protection circuit is built in. When overvoltage +Vout protection operates, release it by shutting down input and re-input Pulse after 10 seconds or setting the voltage of RC2 terminal to logic to load turn off output. -
Page 6: Remote On/Off
Instruction Manual AC-DC Power Supplies Enclosed Type 3.7 Constant current set value external variables 2.2kΩ ¡ The output current for the constant current can be adjustable by 2.2kΩ the external voltage applied to between ITRM and COM on CN3. 150Ω 150Ω... -
Page 7: Communication Function
Instruction Manual AC-DC Power Supplies Enclosed Type OPEN 0.1mF 100kW or CN2 Load Fig.3.4 Internal circuit of PG Fig. 3.2 When not using remote sensing function ¡ Please note the followings when you use the alarms (PG signal). Wire as close as possible 1 The PG signal turns to “High”... -
Page 8: Parallel Operation/Master-Slave Operation
Instruction Manual AC-DC Power Supplies Enclosed Type and input is restarted after 10 seconds or setting the voltage of 4 Series/Parallel Operation RC2 terminal to logic to turn off output. 4.2 Parallel Operation/Master-slave Operation 4.1 Series Operation ¡ Wiring method with series operation is shown in Fig.4.2. ¡... -
Page 9: Assembling And Installation Method
Fig. 5.1. No.2 (Slave) 1.5mm Chassis of Chassis of customer system PCA600F Load No.1 (Master) Screw M4 6mm max Fig.5.1 Mounting screw ¡ Please do not block built-in fans and ventilation holes. - Page 10 Io=20% (Vin=85 to 264VAC) Io=50% (Vin=85 to 264VAC) Io=100% (Vin=85 to 170VAC) Ambient temperature [C] Io=100% (Vin=170 to 264VAC) (b) PCA600F-12,-15,-24 -P2 Fig.5.3 Ambient temperature derating curve *With derating due to input voltage ¡ Input Voltage Derating Curve 10,000 Input voltage derating curve is shown in Fig.5.4.
-
Page 11: Output Current Monitor
Instruction Manual AC-DC Power Supplies Enclosed Type When you connect a DC-DC converter, a current a few times 6 Others higher than normal current may flow at start-up. Please check the current. ¡ Output voltage can be varied (5V to 12V). 6.1 Output Current Monitor Please contact us for more details ¡... -
Page 12: Outline Of Options
¡ Option -T units have a terminal block in stead of an output bus bar. Fig.7.2 Temperature measurement point ¡ For PCA600F, this option is available in -12V, -15V and -24V types. ¡ When wiring the load wire, select the wire in consideration of the heat generation so that the temperature of points A in Fig.
Need help?
Do you have a question about the PCA600F and is the answer not in the manual?
Questions and answers