BenQ LU960UST Installation Manual
  1. Manuals
  2. Brands
  3. BenQ Manuals
  4. Projector
  5. LU960UST
  6. Installation manual

BenQ LU960UST Installation Manual

Hide thumbs Also See for LU960UST:
Table of Contents

Advertisement

Quick Links

Digital Projector
Installation Guide
Installation Projector
| LU960UST
Guide d'installation du projecteur numérique
Digitalprojektor Installationsanleitung
Guida all'installazione del proiettore digitale
Р
а
а

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LU960UST and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for BenQ LU960UST

Summary of Contents for BenQ LU960UST

  • Page 1 Digital Projector Installation Guide Installation Projector | LU960UST Guide d’installation du projecteur numérique Digitalprojektor Installationsanleitung Guida all'installazione del proiettore digitale Р а а...

  • Page 2: Table Of Contents

    Projector dimension ................14 RS232 command control ..............15 RS232 pin assignment ....................15 RS232 serial port with a crossover cable ..............15 PJLink ..........................23 Please visit below website for latest version of User Manual / Installation Guide. http://business-display.benq.com/ V1.00...

  • Page 3: Notice

    Notice Notice on laser This symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the instructions are closely followed. y Laser class (for USA) This Laser Product is designated as Class 3R during all procedures of operation and complies with IEC/EN 60825-1:2007.

  • Page 4: Cooling Notice

    Cooling notice Allow at least 50 cm (19.7 inch) for clearance around the exhaust vent. Make sure no objects block air inlet within 50 cm (19.7 inch). Keep the outlet at least 1 m away from the inlets of other projectors. Air outlet Air inlet •...
  • Page 5 • Allow at least 50 cm of clearance around the exhaust vent. Minimum 50 cm Minimum 50 cm (19.69 inch) (19.69 inch) Minimum 50 cm (19.69 inch) Minimum 50 cm (19.69 inch) • Ensure that the air intake vents do not recycle hot air from the exhaust vent. •...

  • Page 6: Product Information

    Product information Packing content Remote Control Power Cord(s) Regulatory Statement Specification LU960UST Projection system 1-CHIP DMD Native resolution 1920*1200 pixels, 16:10 Light source Laser diodes Power consumption 500Watts (Normal mode)/ 380Watts (Eco mode) Dimension 480 x 157.4 x 473 mm...

  • Page 7: Terminals

    Make sure the port is valid before inserting a wired remote controller. The remote controller may be damaged in case of an invalid port, e.g. a wired remote controller is connected to trigger output. For more information about upgrading firmware via Lan, please contact BenQ service.

  • Page 8: Remote Control

    Remote control ON / OFF Toggles the projector between standby mode and on. KEYSTONE+/KEYSTONE- Manually corrects distorted images resulting from an angled projection. VOLUME +/VOLUME - Increases/decreases the projector volume. QUICK INSTALL Displays the Quick Install OSD menu. MUTE Toggles projector audio between on and off. Arrow keys (▲...
  • Page 9 OVERSCAN Press to select overscan mode. FREEZE Freezes the projected image. LAMP MODE Press to display OSD menu to select desired light mode. 3D MODE Press to display 3D setup menu. INFO. Press to display INFORMATION menu. LIGHT Press to open backlight of remote controller. CLEAR Clear remote ID SET assigned to all projectors.

  • Page 10: Installation

    Installation Projection table • LU960UST The screen aspect ratio is 16:10 and the projected picture is 16:10. Note: To optimize the projection quality, we suggest to project images in an area without grayscale. Offset Distance (mm) Distance (mm) Diagonal Image Width...
  • Page 11 Note: • For more visualized instructions, please go to BenQ calculator website http://projectorcalculator.benq.com/. • Ceiling installation must be done by a qualified professional. Contact your dealer for more information. It is not recommended you install the projector yourself. • Only use the projector on a solid, level surface. Serious injury and damage can occur if the projector is dropped.

  • Page 12: Led Indicator

    LED indicator y LED Usage LED Name Detailed Description Display the power on/off sequence status Orange : Power Off (Green + Red) Power LED Green : Power On Blink : Warming up/Shutting Down & Cooling / Error Code Display the Thermal status (Fan Fail, Over Temperature, etc.) Temperature Status LED Red : Thermal Over Temperature...
  • Page 13 Power Temp Light Status & Description Case open Orange Filter replace warning Orange Flashing Green Thermal break sensor error Orange Flashing y Burn-In Messages Power Temp Light Status & Description Burn-in ON Green Burn-in OFF Green Green Green y Lamp Error Messages Power Temp Light...
  • Page 14 Power Temp Light Status & Description Fan 11 error (the actual fan speed is outside the desired Green Flashing Flashing speed) Fan 12 error (the actual fan speed is outside the desired Green Flashing speed) Temperature 1 error (over limited temperature) Green Thermal Sensor 1 open error Green...

  • Page 15: Projector Dimension

    Projector dimension Unit: mm 163.4 480.0 154.4 240.0 AIR INLET AIR EXHAUST 157.4 159.6 163.1 46.0 388.0 70.0 180.0 159.6...

  • Page 16: Rs232 Command Control

    RS232 command control RS232 pin assignment Serial Serial Short with pin8 Short with pin7 Ground RS232 serial port with a crossover cable Ground Function Type Operation ASCII Power Write Power On <CR>*pow=on#<CR> Write Power off <CR>*pow=off#<CR> Read Power Status <CR>*pow=?#<CR> Source Write COMPUTER/YPbPr...
  • Page 17 Function Type Operation ASCII Audio Source Write Audio pass Through off <CR>*audiosour=off#<CR> Select Write Audio-Computer1 <CR>*audiosour=RGB#<CR> Write Audio-HDMI <CR>*audiosour=hdmi#<CR> Write Audio-HDMI2 <CR>*audiosour=hdmi2#<CR> Write DisplayPort <CR>*audiosour=dp#<CR> Write HDBaseT <CR>*audiosour=hdbaset#<CR> Read Audio pass Status <CR>*audiosour=?#<CR> Picture Mode Write Presentation <CR>*appmod=preset#<CR> Write sRGB <CR>*appmod=srgb#<CR>...
  • Page 18 Function Type Operation ASCII Picture Setting Write Contrast + <CR>*con=+#<CR> Write Contrast - <CR>*con=-#<CR> Write Set Contrast value <CR>*con=value#<CR> Read Contrast value <CR>*con=?#<CR> Write Brightness + <CR>*bri=+#<CR> Write Brightness - <CR>*bri=-#<CR> Write Set Brightness value <CR>*bri=value#<CR> Read Brightness value <CR>*bri=?#<CR> Write Color + <CR>*color=+#<CR>...
  • Page 19 Function Type Operation ASCII Picture Setting Write 4 Corners Top-Right-X Decrease <CR>*cornerfittrx=-#<CR> Write 4 Corners Top-Right-X Increase <CR>*cornerfittrx=+#<CR> Read 4 Corners Top-Right-X Status <CR>*cornerfittrx=?#<CR> Write 4 Corners Top-Right-Y Decrease <CR>*cornerfittry=-#<CR> Write 4 Corners Top-Right-Y Increase <CR>*cornerfittry=+#<CR> Read 4 Corners Top-Right-Y Status <CR>*cornerfittry=?#<CR>...
  • Page 20 Function Type Operation ASCII Operation Write Projector Position-Front Table <CR>*pp=FT#<CR> Settings Write Projector Position-Rear Table <CR>*pp=RE#<CR> Write Projector Position-Rear Ceiling <CR>*pp=RC#<CR> Write Projector Position-Front Ceiling <CR>*pp=FC#<CR> Read Projector Position Status <CR>*pp=?#<CR> Write Quick auto search <CR>*QAS=on#<CR> Write Quick auto search <CR>*QAS=off#<CR>...
  • Page 21 Function Type Operation ASCII Miscellaneous Read Model Name <CR>*modelname=?#<CR> Read System F/W Version <CR>*sysfwversion=?#<CR> Read Scaler F/W Version <CR>*scalerfwversion=?#<CR> Read Lan F/W Version <CR>*lanfwversion=?#<CR> Read MCU F/W Version <CR>*mcufwversion=?#<CR> Write Blank On <CR>*blank=on#<CR> Write Blank Off <CR>*blank=off#<CR> Read Blank Status <CR>*blank=?#<CR>...
  • Page 22 Function Type Operation ASCII Color Write Tint + <CR>*tint=+#<CR> Calibration Write Tint - <CR>*tint=-#<CR> Write Set Tint value <CR>*tint=value#<CR> Read Get Tint value <CR>*tint=?#<CR> Write Set gamma value <CR>*gamma=value#<CR> Read Gamma value status <CR>*gamma=?#<CR> Write Set HDR Brightness value <CR>*hdrbri=value#<CR> Read Get HDR Brightness value <CR>*hdrbri=?#<CR>...
  • Page 23 Function Type Operation ASCII Write Gain + <CR>*gain=+#<CR> Write Gain - <CR>*gain=-#<CR> Write Set Gain value <CR>*gain=value#<CR> Read Get Gain value <CR>*gain=?#<CR> Service Read Error Code report <CR>*error=report#<CR> Read FAN 1 speed <CR>*fan1=?#<CR> Read FAN 2 speed <CR>*fan2=?#<CR> Read FAN 3 speed <CR>*fan3=?#<CR>...

  • Page 24: Pjlink

    LAMP? xxxxxxxxxxxx 1st number (1-5 digitals): Light source 1 runtime tus query Input selection 11 12 21 31 32 33 INST? LU960UST list query Projector name Returns the name set in [PROJECTOR NAME] of [NET- NAME? xxxxx query WORK SETUP]...
  • Page 25 Remark Details Return String Manufacturer INF1? BenQ Returns manufacturer name name query Model name que- INF2? LU960UST Returns moder name Other informa- INF0? xxxxx Returns information such as version number tion queries Class information CLASS? Returns class for PJLink query Note: RS-232 baud rate options are 2400, 4800, 9600, 14400, 19200, 38400, 57600 and 115200 (Default : 115200).
  • Page 27 P/N: 4J.JN401.001...

Table of Contents