Related Manuals for rako WK
Summary of Contents for rako WK
-
Page 1: Table Of Contents
7 Downloading the project file 8 Events 8.1 Setting Events using Rasoft Pro 8.2 Setting Events via the HUB webpages 8.3 Setting Events using the Rako App. 9 Mappings 9.1 Mapping wireless commands to give multi-room functionality 9.2 Triggering Macros from Maps 10 Macros 10.1 Writing Macros... -
Page 2: Functions Of The Wk-Hub
Step 1: P lug RJ11 cable provided into the WK-HUB and an available RJ11 port in a RAK-LINK/RAK-STAR/WPCON-C etc. Step 2: P lug the Ethernet patch cable from the WK-HUB to a spare port in a router or network switch. -
Page 3: Discovering The Hub And Setting The House Number
If it does not appear press “Refresh”. 3.2 Setting up the HUB using the Webpage Wizard To access the HUB Webpages right click the communication device in the bottom right of the software. Select “Open in Browser” WK-HUB Manual Version 1.0.0... -
Page 4: Managing The Hub House Number
Leaving the HUB on the default House address of 1 is strongly discouraged. Leaving the House number as 1 drastically increases the likelihood of interface from nearby Rako systems. The HUB always has a d efault House Address of 1 i f has not been setup before . When beginning any programming using the HUB it is important to first ensure the House is set the same as the address used when creating the Project File. -
Page 5: If You Cannot Connect To The Hub
By default the HUB is connected via DHCP, this and other network settings can be edited via the HUB webpages. It is possible to clear all network settings from a HUB. Please call Rako technical support for information on how to do this. -
Page 6: Linking The Hub To Cloud Services
Step 3 - O nce logged in the code within the HUB will be automatically verified. Please wait, this process may take a couple of minutes WK-HUB Manual Version 1.0.0... -
Page 7: Adding The Hub As A Device To Rasoft Pro
The “Smartphone/Web Data” tab is used to upload the Project File to the HUB. Once selected it will open the page as below. Press “ S ave & Upload Room Data To HUB ” to upload. WK-HUB Manual Version 1.0.0... -
Page 8: Downloading The Project File
If information has been uploaded to the HUB then it is possible to import the Room, Channel and Scene data into a blank project file. The tab used for downloading information from the HUB is called “ R oom Import ” select it to open the page below. WK-HUB Manual Version 1.0.0... -
Page 9: Events
Step 4: P ress “Refresh Channel Levels” to write the Scene data in to the Project File. 8 Events Events can be viewed, added and changed using either Rasoft Pro, The Rako App or HUB webpages. It should be noted that calendar event conditions can only be set fom the HUB webpage interface. -
Page 10: Setting Events Using Rasoft Pro
The “Event Trigger” and “Active Days” are the timing conditions that define when the event will occur. The dawn and dusk settings can be changed via the location settings in the webpage interface. An offset from this value can be set from this screen if desired. WK-HUB Manual Version 1.0.0... -
Page 11: Setting Events Via The Hub Webpages
Mapping and events created in Rasoft Pro will appear here (as above) but will not be editable. Please consult Rako technical support if you have any questions about “Activities” Events can be created using the interface below, this interface works in a very similar way to that found in Rasoft Pro and the App. -
Page 12: Setting Events Using The Rako App
Once all information has been filled in press “Submit” to activate the Event. 8.3 Setting Events using the Rako App. Events can also be created via the Rako App. The method to create events in the App is essentially the same as detailed above. - Page 13 Where WCMs are RNCs are used in the system use K eypad Mapping r ather than HUB Mapping. It is also possible to “Enable” and “Disable” maps from other commands via the “Mapping Control” Action. WK-HUB Manual Version 1.0.0...
-
Page 14: Mapping Wireless Commands To Give Multi-Room Functionality
With this simply Macro the HUB will just run through the three commands listed. More complex functionality can be achieved by using commands in the tables outlined below. 10.1 Writing Macros Macro steps can be one of 4 types: WK-HUB Manual Version 1.0.0... -
Page 15: Triggering Macros
Record : Used to create a log of the used of the system. Playback : Used when the house is unoccupied to replay the information gathered in “Record”. Idle : Used when the system is in normal occupied operation and no recording is being made. WK-HUB Manual Version 1.0.0... -
Page 16: Udp Feedback
12.2 UDP feedback log When more detailed or long term feedback is required then a log of commands received/transmitted by the HUB can be opened. In the toolbar select “Window” - ”Output” - ”Output” (as shown below). WK-HUB Manual Version 1.0.0... -
Page 17: Hub Webpages Logs
A timestamped log of system activity can be found within the HUB webpages. These can be accessed by selecting the “Logs” section of the HUB webpages. As well as a description of the address (Room and Channel) and command the source of the command can also be viewed. WK-HUB Manual Version 1.0.0...