Emerson PACSystems RX3i Quick Start Manual
Ethernet 104 slave module
Hide thumbs
Also See for PACSystems RX3i:
- User manual (232 pages) ,
- Application manual (37 pages) ,
- Manual (37 pages)
Related Manuals for Emerson PACSystems RX3i
Summary of Contents for Emerson PACSystems RX3i
- Page 1 QUICK START GUIDE GFK-2948A Sep 2019 PACSystems RX3i ETHERNET 104 SLAVE MODULE (IC695EIS001)
-
Page 2: Table Of Contents
3.5. Status and Diagnostic Data ..............14 Module Status Data ....................14 4.1. Problems during Power-Up and Reset ..............15 4.2. Additional Information ................17 PACSystems RX3i User Manuals ................17 5.1. Information about IEC 60870-5-104 ..............17 5.2. Contents... - Page 3 These instructions do not purport to cover all details or variations in equipment, nor to provide for every possible contingency to be met during installation, operation, and maintenance. The information is supplied for informational purposes only, and Emerson makes no warranty as to the accuracy of the information included herein. Changes, modifications, and/or improvements to equipment and specifications are made periodically and these changes may or may not be reflected herein.
-
Page 4: User Features
Overview The PACSystems RX3i Ethernet 104 Server Module, catalog number IC695EIS001 implements the IEC 104 protocol, server side. It permits a PACSystems RX3i controller to be connected to an Ethernet network using a standard Ethernet TCP/IP connection scheme, and serve data to one or many IEC 104 clients, using interrogation polls, or report by exception (RBE) functions to retrieve data. -
Page 5: Light-Emitting Diode Indicators (Leds)
Quick Start Guide Section 1 GFK-2948A Sep 2019 1.3. Light-Emitting Diode Indicators (LEDs) State Indicates Fast Blink ETHERNET OK Performing LAN OK Diagnostics LOG EMPTY ETHERNET OK Slow Blink Waiting for Ethernet LAN OK configuration from LOG EMPTY † ETHERNET OK Slow Blink †... - Page 6 Quick Start Guide Section 1 GFK-2948A Sep 2019 State Indicates Port LEDs (one pair for Port 1A, second pair for Port 1B) 100 Mbps Active 100 Mbps 100 Mbps Not Achieved Traffic Detected on Rapid Blink Port LINK No Traffic Detected on Port User Features...
-
Page 7: Station Manager Port
The Station Manager port provides a means to access the module through a terminal interface. This function can alternatively be accessed over the Ethernet network. A Station Manager interface application can be downloaded from Emerson Global Customer Care... -
Page 8: Hardware Installation
RX3i rack systems, refer to GFK-2314, RX3i System Manual. If you need technical help, contact Technical Support. For phone numbers and email addresses, refer to GFK-2949, PACSystems RX3i Ethernet IEC 104 Server Module User Manual the section, Contact Information. -
Page 9: Installation In Hazardous Areas
Quick Start Guide Section 2 GFK-2948A Sep 2019 2.3. Installation in Hazardous Areas The following information is for products bearing the UL marking for Hazardous Areas or ATEX marking for explosive atmospheres: CLASS 1 DIVISION 2 GROUPS ABCD • This equipment is an open-type device and is meant to be installed in an enclosure suitable for the environment that is only accessible with the use of a tool. -
Page 10: Module Installation
Quick Start Guide Section 2 GFK-2948A Sep 2019 2.4. Module Installation The EIS001 is compatible with all RX3i CPU (no model restrictions). The EIS001 supports insertion into and removal from an Rx3i backplane which is under power. This module may be installed in any available RX3i backplane slot in the main (CPU) rack. -
Page 11: Station Manager Port Connections
Quick Start Guide Section 2 GFK-2948A Sep 2019 2.5. Station Manager Port Connections † Pin No Signal Direction Description Data Carrier Detect Transmit Data Receive Data Data Set Ready Signal Ground Data Terminal Ready Clear to Send Ready to Send Ring Indicator †... -
Page 12: Configuration
PACSystems RX3i CPU Firmware 7.18 or later. • Proficy Machine Edition version 8.50 SIM 9 or later. • GFK-2949, PACSystems RX3i Ethernet 104 Server Module User Manual, available from the Emerson Global Support https://www.emerson.com/Industrial- Automation-Controls/support. You will need to refer to this manual to fully configure and commission the EIS001. - Page 13 Quick Start Guide Section 3 GFK-2948A Sep 2019 Once added to the rack location, set up the EIS001 parameters in the Settings and RS- 232 Port (Station Manager) tabs as needed for the application. Configuration...
-
Page 14: Confirm Eis001 Communication With The Cpu
Quick Start Guide Section 3 GFK-2948A Sep 2019 3.2. Confirm EIS001 Communication with the CPU Power up the target RX3i system. In PME, go “online”, right-click on the target and select Online Commands, Show Status…, Details, to display the Device Information Details window. -
Page 15: Program Commreqs For Eis001 Initialization
Quick Start Guide Section 3 GFK-2948A Sep 2019 3.3. Program COMMREQs for EIS001 Initialization A single COMMREQ instruction must be passed from the CPU to the EIS001 in order to configure the IEC 104 Server module attributes. These are explained in the Configuration portion of GFK-2949, Ethernet IEC 104 Server Module User Manual. - Page 16 Quick Start Guide Section 3 GFK-2948A Sep 2019 to GFK-2949, PACSystems RX3i Ethernet 104 Server Module User Manual for more information. Configuration...
-
Page 17: Status And Diagnostic Data
Quick Start Guide Section 4 GFK-2948A Sep 2019 4. Status and Diagnostic Data 4.1. Module Status Data Bit# LAN Interface Status Bits 0 (lsb) Port 1A Full Duplex Port 1A 100 Mbps Port 1B Full Duplex Port 1B 100 Mbps Network Time Locked Redundant IP Address is Active Reserved... -
Page 18: Problems During Power-Up And Reset
Hardware failure All Indicator LEDs off. Invalid bootstrap Module unresponsive. image No Indicator LEDs turn on Return the module Emerson and the module is Invalid boot unresponsive, or image The STATUS LED is solid green and is the only LED... - Page 19 Quick Start Guide Section 4 GFK-2948A Sep 2019 Problem Indication Action Module shuts Module is operating without a IEC 104 traffic stops after 4 down after 4 license, Contact customer hours of operation hours service Status & Diagnostic Data...
-
Page 20: Additional Information
Sep 2019 5. Additional Information 5.1. PACSystems RX3i User Manuals GFK-2949, PACSYstems RX3i Ethernet IEC 104 Server Module User Manual GFK-2222, PACSystems RX3i and RX7i CPU Reference Manual GFK-2224, TCP/IP Ethernet Communications for PACSystems RX3i & RX7i User’s Manual GFK-2225, TCP/IP Ethernet Communications for PACSystems Station Manager... - Page 21 © 2019 Emerson. All rights reserved. Emerson Terms and Conditions of Sale are available upon request. The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their respective owners.