DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port User Manual Contents Chapter 1. Introduction.........5 Contents and Audience............5 Conventions..............5 Document Structure............5 Chapter 2. Overview..........6 General Information............6 Specifications..............8 Product Appearance............15 Front Panel..............15 Back Panel...............17 Delivery Package............19 Chapter 3.
Page 3
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port User Manual Settings / Internet............76 WAN..............76 Creating Dynamic IPv4 or Static IPv4 WAN Connection....78 Creating Dynamic IPv6 or Static IPv6 WAN Connection....81 Creating PPPoE WAN Connection..........85 Creating PPTP, L2TP, or L2TP over IPsec WAN Connection....90...
Page 4
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port User Manual Functions / Advanced............182 UPnP IGD..............182 Remote Access............183 Virtual Servers............185 TR-069 Client............188 Static Route............190 Dynamic DNS.............192 IPsec..............194 Ports Settings............202 Redirect..............205 IGMP/MLD..............206 ALG/Passthrough............207 Management..............209 System Time.............209 System Log..............212...
Chapter 2 gives an overview of the router's hardware and software features, describes its appearance and the package contents. Chapter 3 explains how to install the router DIR-825 and configure a PC in order to access its web- based interface.
USB modem. Also you are able to connect the wireless router DIR-825 to a cable or DSL modem or to a private Ethernet line and use a high-speed Internet connection to successfully fulfill a wide range of professional tasks.
Page 7
(the interface is available in several languages). The Setup Wizard allows you to quickly switch DIR-825 to one of the following modes: router (for connection to a wired or wireless ISP), access point, repeater, or client, and then configure all needed setting for operation in the selected mode in several simple steps.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Overview User Manual Specifications Hardware Processor · RTL8197FH-VG (1GHz) · 128MB, DDR2, built in processor Flash · 128MB, SPI NAND Interfaces · 10/100/1000BASE-T WAN port ·...
Page 9
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Overview User Manual Software Network functions · DHCP server/relay · Advanced configuration of built-in DHCP server · Stateful/Stateless mode for IPv6 address assignment, IPv6 prefix delegation ·...
Page 10
SSH/TELNET/WEB (HTTP/HTTPS) · Multilingual web-based interface for configuration and management · Support of D-Link Assistant application for Android and iPhone smartphones · Notification on connection problems and auto redirect to settings · Firmware update via web-based interface · Automatic notification on new firmware version ·...
Page 11
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Overview User Manual Wireless Module Parameters Transmitter output power · 802.11a (typical at room temperature 25 °C) 15dBm at 6, 54Mbps The maximum value of the transmitter ·...
Page 12
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Overview User Manual Wireless Module Parameters 5GHz, HT20 -95dBm at MCS0 -93dBm at MCS1 -90dBm at MCS2 -87dBm at MCS3 -83dBm at MCS4 -79dBm at MCS5...
Page 13
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Overview User Manual Physical Parameters Dimensions (L x W x H) · 181 x 132.5 x 47.71 mm (7.13 x 5.22 x 1.88 in) Weight ·...
Page 14
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Overview User Manual Supported USB modems · Alcatel IK40V · D-Link DWM-222 · Huawei E3131 · Huawei E3272 · Huawei E3351 · Huawei E3372s ·...
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Overview User Manual Product Appearance Front Panel Figure 1. Front panel view. Mode Description The router is powered on. Solid blue Power The router is powered off.
Page 16
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Overview User Manual Mode Description The default wired WAN connection is off, or • No light there are no WAN connections created. • Data transfer through the Wi-Fi network of the relevant band.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Overview User Manual Back Panel Figure 2. Back panel view. Name Description A button to restore the factory defaults. RESET To restore the factory defaults, push the button (with the device turned on), hold it for 10 seconds, and then release the button.
Page 18
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Overview User Manual Name Description A port to connect to a cable or DSL modem or to a private Ethernet line (it is recommended to use the cable included in the delivery package).
• “Quick Installation Guide” (brochure). • The “User Manual” and “Quick Installation Guide” documents are available on D-Link website (see www.dlink.ru). Using a power supply with a different voltage rating than the one included will cause damage and void the warranty for this product.
(hereinafter referred to as “the router”) is performed via the built-in web-based interface. The web- based interface is available from any operating system that supports a web browser. Also you can use D-Link Assistant application for Android or iPhone mobile devices (smartphones or tablets).
Page 21
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual USB Modem To connect to an LTE or 3G network, you should use a USB modem. Connect it to the USB port of the router, then access the web-based interface of the router, and you will be able to configure a connection to the Internet.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual Connecting to PC PC with Ethernet Adapter 1. Connect an Ethernet cable between any of LAN ports located on the back panel of the router and the Ethernet port of your PC.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual Obtaining IP Address Automatically (OS Windows 7) 1. Click the Start button and proceed to the Control Panel window. 2. Select the Network and Sharing Center section. (If the Control Panel has the category...
Page 24
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual 3. In the menu located on the left part of the window, select the Change adapter settings line. Figure 4. The Network and Sharing Center window.
Page 25
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual 4. In the opened window, right-click the relevant Local Area Connection icon and select the Properties line in the menu displayed.
Page 26
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual 5. In the Local Area Connection Properties window, on the Networking tab, select the Internet Protocol Version 4 (TCP/IPv4) line. Click the Properties button.
Page 27
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual 6. Make sure that the Obtain an IP address automatically and Obtain DNS server address automatically choices of the radio buttons are selected. Click the OK button.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual Obtaining IP Address Automatically (OS Windows 10) 1. Click the Start button and proceed to the Settings window. 2. Select the Network & Internet section.
Page 29
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual 3. In the Change your network settings section, select the Change adapter options line. Figure 9. The Network & Internet window.
Page 30
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual 4. In the opened window, right-click the relevant Local Area Connection icon and select the Properties line in the menu displayed.
Page 31
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual 5. In the Local Area Connection Properties window, on the Networking tab, select the Internet Protocol Version 4 (TCP/IPv4) line. Click the Properties button.
Page 32
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual 6. Make sure that the Obtain an IP address automatically and Obtain DNS server address automatically choices of the radio buttons are selected. Click the OK button.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual PC with Wi-Fi Adapter 1. To connect via USB modem: connect your USB modem to the USB port located on the front panel of the router.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual Obtaining IP Address Automatically and Connecting to Wireless Network (OS Windows 7) 1. Click the Start button and proceed to the Control Panel window.
Page 35
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual 6. Make sure that the Obtain an IP address automatically and Obtain DNS server address automatically choices of the radio buttons are selected. Click the OK button.
Page 36
User Manual 9. In the opened Wireless Network Connection window, select the wireless network DIR-825 (for operating in the 2.4GHz band) or DIR-825-5G (for operating in the 5GHz band) and click the Connect button. Figure 16. The list of available networks.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual Obtaining IP Address Automatically and Connecting to Wireless Network (OS Windows 10) 1. Click the Start button and proceed to the Settings window.
Page 38
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual 6. Make sure that the Obtain an IP address automatically and Obtain DNS server address automatically choices of the radio buttons are selected. Click the OK button.
Page 39
User Manual 9. In the opened Wireless Network Connection window, select the wireless network DIR-825 (for operating in the 2.4GHz band) or DIR-825-5G (for operating in the 5GHz band) and click the Connect button. Figure 20. The list of available networks.
(create a WAN connection, change the parameters of the wireless network, specify the settings of the firewall, etc.). For security reasons, DIR-825 with default settings cannot connect to the Internet. To get started, please set your own password used to access the web-based interface and, if needed, configure other settings recommended by your ISP.
Page 41
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual If you configured the device previously, after access to the web-based interface the login page opens. Enter the username (admin) in the Username field and the password you specified in the Password field, then click the LOGIN button.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual Web-based Interface Structure Home Page The Home page displays the current status of the router in the form of an interactive diagram. You can click each icon to display information about each part of the network at the bottom of the screen.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual Internet Section Click the Internet icon to view more details about your Internet connection. Figure 27. The Home page. The Internet section.
Page 44
User Manual DIR-825 Section Click the DIR-825 icon to view details about the router and its wireless settings. Figure 28. The Home page. The DIR-825 section. Here you can see the router’s current Wi-Fi network name in the 2.4GHz and 5GHz bands, the...
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual Wi-Fi Clients Section Click the Wi-Fi clients icon to view details about wireless clients connected to the router. Figure 29. The Home page. The Wi-Fi clients section.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual Menu Sections To configure the router use the menu bar in the top part of the page. The Settings section provides you with the most essential settings.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Installation and Connection User Manual Notifications The router's web-based interface displays notifications in the top right part of the page. Figure 30. The web-based interface notifications.
If you perform initial configuration of the router via Wi-Fi connection, please make sure that you are connected to the wireless network of DIR-825 (see the WLAN name (SSID) on the barcode label on the bottom panel of the device) and click the NEXT button.
Page 49
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual On the opened page, click YES in order to leave the current language of the web-based interface or click NO to select another language.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Selecting Operation Mode Select the needed operation mode and click the NEXT button. Router In order to connect your device to a wired ISP, on the Device mode page, from the Connection method list, select the Autonomous value.
Page 51
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In order to connect your device to a wireless ISP (WISP), on the Device mode page, from the Connection method list, select the Autonomous value. Then from the Work mode list select the WISP Repeater value.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Access Point or Repeater In order to connect your device to a wired router for adding a wireless network to the existing local network, on the Device mode page, from the Connection method list, select the Autonomous value.
Page 53
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In order to let wired PCs connected to your device access the network of a wireless router, on the Device mode page, from the Connection method list, select the Autonomous value.
Configuring via Web-based Interface User Manual Mesh Network Main Device (Controller) In order to configure DIR-825 as a main device of your mesh network, from the Connection method list, select the EasyMesh value. Then from the Device Role list, select the Controller value.
Page 55
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In order to connect your main device to the network of a 3G or LTE operator, from the Work mode list, select the Mobile Internet value.
Page 56
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In order to connect your main device to a wireless ISP (WISP), from the Work mode list, select the WISP Repeater value. In this mode you can connect your device to another access point, configure a WAN connection, set your own settings for the wireless network in the 2.4GHz and...
Configuring via Web-based Interface User Manual Mesh Network Subordinate Device (Agent) In order to configure DIR-825 as a subordinate device of your mesh network, from the Connection method list, select the EasyMesh value. Then from the Device Role list, select the Agent value.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Creating 3G/LTE WAN Connection This configuration step is available for the Mobile Internet mode. 1. If the PIN code check is enabled for the SIM card inserted into your USB modem, enter the PIN code in the PIN field and click the APPLY button.
Page 59
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual 3. Click the NEXT button to continue or click the BACK button to return to the previous page. If the router failed to create a WAN connection automatically, click the CONFIGURE MANUALLY button.
If you want to manually assign the LAN IPv4 address for DIR-825, do not select the Automatic obtainment of IPv4 address checkbox and fill in the IP address, Subnet mask, DNS IP address, Hostname fields and, if needed, the Gateway IP address field.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Wi-Fi Client This configuration step is available for the WISP Repeater, Repeater, and Client modes. 1. On the Wi-Fi Сlient page, click the WIRELESS NETWORKS button and select the network to which you want to connect in the opened window.
Page 62
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description The number of the key (from first to fourth) which will be used for Default key ID WEP encryption.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Configuring Wired WAN Connection This configuration step is available for the Router and WISP Repeater modes. You should configure your WAN connection in accordance with data provided by your Internet service provider (ISP).
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Static IPv4 Connection Figure 50. The page for configuring Static IPv4 WAN connection. Fill in the following fields: IP address, Subnet mask, Gateway IP address, and DNS IP address.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Static IPv6 Connection Figure 51. The page for configuring Static IPv6 WAN connection. Fill in the following fields: IP address, Prefix, Gateway IP address, and DNS IP address.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual PPPoE, IPv6 PPPoE, PPPoE Dual Stack, PPPoE + Dynamic IP (PPPoE Dual Access) Connections Figure 52. The page for configuring PPPoE WAN connection.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual PPPoE + Static IP (PPPoE Dual Access) Connection Figure 53. The page for configuring PPPoE + Static IP (PPPoE Dual Access) WAN connection.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual PPTP + Dynamic IP or L2TP + Dynamic IP Connection Figure 54. The page for configuring PPTP + Dynamic IP WAN connection.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual PPTP + Static IP or L2TP + Static IP Connection Figure 55. The page for configuring PPTP + Static IP WAN connection.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Configuring Wireless Network This configuration step is available for the Mobile Internet, Router, Access point, WISP Repeater, and Repeater modes.
Page 71
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual 5. If you want to create an additional wireless network isolated from your LAN in the 2.4GHz band, select the Enable guest network checkbox (available for the Router and WISP Repeater modes only).
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Configuring LAN Ports for IPTV/VoIP This configuration step is available for the Router mode. On the IPTV page, select the Is an STB connected to the device checkbox.
Page 73
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual On the VoIP page, select the Is an IP phone connected to the device checkbox. Figure 59. The page for selecting a LAN port to connect an VoIP phone.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Changing Web-based Interface Password On this page, you should change the default administrator password. To do this, enter a new password in the User’s interface password and Password confirmation fields.
Page 75
If problems of connection have not been solved, contact the technical support of your ISP (as a rule, the technical support phone is provided with the agreement) or the D-Link technical support. To specify other settings, click the ADVANCED SETTINGS button. After clicking the ADVANCED SETTINGS button, the Home page opens (see the Home Page section, page 42).
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Settings / Internet On the Settings / Internet / WAN page, you can create and edit connections used by the router.
Page 77
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 63. The Settings / Internet / WAN page. The advanced mode. To create a new connection, click the ADD button ( ) in the Connections List section.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Creating Dynamic IPv4 or Static IPv4 WAN Connection On the connection creation page, in the General Settings section, select the relevant value from the Connection type drop-down list and specify the needed values.
Page 79
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 65. The page for creating a new Static IPv4 connection. The Ethernet section. Parameter Description Ethernet A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding.
Page 80
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 66. The page for creating a new Static IPv4 connection. The IPv4 section. Parameter Description IPv4 For Static IPv4 type IP address Enter an IP address for this WAN connection.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Creating Dynamic IPv6 or Static IPv6 WAN Connection On the connection creation page, in the General Settings section, select the relevant value from the Connection type drop-down list and specify the needed values.
Page 82
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Move the switch to the right to allow using RIPng for this RIPng connection. Figure 68. The page for creating a new Static IPv6 connection. The Ethernet section.
Page 83
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 69. The page for creating a new Static IPv6 connection. The IPv6 section. Parameter Description IPv6 For Static IPv6 type IPv6 address Enter an IPv6 address for this WAN connection.
Page 84
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Primary IPv6 DNS Enter addresses of the primary and secondary IPv6 DNS servers in server / Secondary IPv6 the relevant fields.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Creating PPPoE WAN Connection On the connection creation page, in the General Settings section, select the relevant value from the Connection type drop-down list and specify the needed values.
Page 86
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 71. The page for creating a new PPPoE connection. The Ethernet section. Parameter Description Ethernet A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding.
Page 87
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 72. The page for creating a new PPPoE connection. The PPP section. Parameter Description Move the switch to the right if you don't need to enter a username Without authorization and password to access the Internet.
Page 88
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description The maximum size of units transmitted by the interface. Select a method of MPPE encryption. No encryption: MPPE encryption is not applied.
Page 89
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 73. The page for creating a new PPPoE connection. The IPv4 section. Parameter Description IPv4 Obtain DNS server...
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Creating PPTP, L2TP, or L2TP over IPsec WAN Connection On the connection creation page, in the General Settings section, select the relevant value from the Connection type drop-down list and specify the needed values.
Page 91
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 75. The page for creating a new PPTP connection. The PPP section. Parameter Description Move the switch to the right if you don't need to enter a username Without authorization and password to access the Internet.
Page 92
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Select a method of MPPE encryption. No encryption: MPPE encryption is not applied. • MPPE 40 128 bit: MPPE encryption with a 40-bit or 128- •...
Page 93
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 76. The page for creating a new PPTP connection. The IPv4 section. Parameter Description IPv4 Obtain DNS server...
Page 94
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Move the switch to the right to enable the PFS option (Perfect Forward Secrecy). If the switch is moved to the right, a new...
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Creating PPPoE IPv6 or PPPoE Dual Stack WAN Connection On the connection creation page, in the General Settings section, select the relevant value from the Connection type drop-down list and specify the needed values.
Page 96
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description If the switch is moved to the right, the router responds to ping Ping requests from the external network through this connection. For security reasons, it is recommended to disable this function.
Page 97
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 80. The page for creating a new PPPoE IPv6 connection. The PPP section. Parameter Description Move the switch to the right if you don't need to enter a username Without authorization and password to access the Internet.
Page 98
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Select a method of MPPE encryption. No encryption: MPPE encryption is not applied. • MPPE 40 128 bit: MPPE encryption with a 40-bit or 128-bit •...
Page 99
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 81. The page for creating a new PPPoE Pv6 connection. The IPv4 section. Parameter Description IPv4 (for the PPPoE Dual Stack type)
Page 100
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Move the switch to the right to configure automatic assignment of Obtain DNS server IPv6 DNS server addresses. Upon that the Primary IPv6 DNS...
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Creating Mobile Internet WAN Connection If the PIN code check is enabled for the SIM card inserted into your USB modem, for correct operation of the mobile WAN connection click the ENTER PIN button in the notification in the top right corner of the page and enter the PIN code in the window displayed.
Page 102
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 84. The page for creating a new Mobile Internet connection. The Modem settings section. Parameter Description Modem settings...
Page 103
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Username A username (login) to connect to the network of the operator. A password to connect to the network of the operator.
Page 104
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 86. The page for creating a new Mobile Internet connection. The Health Check section. Parameter Description Health Check...
Page 105
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description IP addresses from the external network that the router will check for availability via ICMP ping mechanism. By default, the router checks the IP address 8.8.8.8.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual VLAN On the Settings / Internet / VLAN page, you can edit existing and create new virtual networks (VLAN), e.g., for distinguishing traffic or specifying additional WAN interfaces.
Page 107
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual To create a new VLAN, click the ADD button ( Figure 88. The page for adding a VLAN. You can specify the following parameters:...
Page 108
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Select a type for each port included in the VLAN. Untagged: Untagged traffic will be transmitted through the •...
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual On the Settings / Internet / DNS page, you can add DNS servers to the system. Figure 89. The Settings / Internet / DNS page.
Page 110
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Specify needed settings for IPv4 in the IPv4 section and for IPv6 in the IPv6 section. If you want to configure automatic obtainment of DNS servers addresses, move the Manual switch to the left.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Settings / WAN Failover On the Settings / WAN Failover page, you can enable the WAN backup function, which provides you with uninterrupted access to the Internet.
Page 112
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 91. The window for changing the priority of a connection. In the opened window, specify the needed parameters.
Page 113
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In the Check with ping section, specify settings of checking the connection using ICMP ping mechanism. Parameter Description Check with ping A time period (in seconds) between regular checks of the hosts’...
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Settings / Wireless network On the Settings / Wireless network page, you can change basic parameters for the wireless interface of the router and configure the basic and additional wireless networks.
Page 115
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In the Basic Settings section, the following parameters are available: Parameter Description To enable Wi-Fi connection, move the switch to the right.
Page 116
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Specify a period of time (in seconds) after which the router Scanning period rescans channels. When you have configured the parameters, click the APPLY button.
Page 117
Move the switch to the left not to limit the maximum bandwidth. If the wireless network broadcasting is disabled, devices cannot connect to the wireless network. Upon that DIR-825 can connect to another access point as a wireless client. To enable/disable broadcasting on a schedule, click the Set schedule button ( ).
Page 118
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description To change or delete the schedule, click the Edit schedule button ). In the opened window, change the parameters and click the SAVE button or click the DELETE FROM SCHEDULE button.
Page 119
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Authentication type Description WPA2-PSK WPA2-based authentication using a PSK. A mixed type of authentication. When this value is selected, devices...
Page 120
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual When the Open or WEP value is selected, the following settings are displayed on the page (unavailable for the wireless network operating modes which support the standard 802.11n or 802.11ac):...
Page 121
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual When the WPA-PSK, WPA2-PSK, WPA-PSK/WPA2-PSK mixed, WPA3-SAE, or WPA2- PSK/WPA3-SEA mixed value is selected, the following fields are displayed on the page: Figure 96.
Page 122
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description For WPA2-PSK, WPA3-SAE, and WPA2-PSK/WPA3-SAE mixed authentication types only. Protected Management Frames help to improve packet privacy protection for wireless data transmission.
Page 123
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description RADIUS server port A port of the RADIUS server. The password which the router uses for communication with the...
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Settings / Network To configure the router's local interface, go to the Settings / Network page. IPv4 Go to the IPv4 tab to change the IPv4 address of the router, configure the built-in DHCP server, specify MAC address and IPv4 address pairs, or add own DNS records.
Page 125
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description The name of the device assigned to its IPv4 address in the local Hostname subnet. For Wi-Fi clients, the device is not available by the domain name, if multicasting is disabled in the additional settings of Wi-Fi.
Page 126
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description The start IP address of the address range used by the DHCP server to Start IP distribute IP addresses to clients.
Page 127
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual To do this, click the ADD button ( Figure 101. Configuring the local interface. The IPv4 tab. The window for configuring a DHCP option.
Page 128
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In the Static IP Addresses section, you can specify MAC address and IPv4 address pairs (set a fixed IPv4 address in the local area network for a device with a certain MAC address). The router...
Page 129
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual If needed, you can add your own address resource records. To do this, click the ADD button ( in the Hosts section (available if the Router or WISP Repeater mode was selected in the Setup Wizard).
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual IPv6 Go to the IPv6 tab to change or add the IPv6 address of the router, configure IPv6 addresses assignment settings, specify MAC address and IPv6 address pairs, or add own DNS records.
Page 131
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In the Dynamic IPv6 Addresses section, you can configure IPv6 addresses assignment settings. Figure 106. Configuring the local interface. The IPv6 tab. The Dynamic IPv6 Addresses section.
Page 132
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In the Static IP Addresses section, you can specify MAC address and IPv6 address pairs (set a fixed IPv6 address in the local area network for a device with a certain MAC address). The router...
Page 133
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual To remove a record, in the Hosts section, select the checkbox located to the left of the relevant line in the table and click the DELETE button ( After completing the work with records, click the APPLY button.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Settings / USB Storage Information On the Settings / USB Storage / Information page, you can view data on the USB storage connected to the router.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual USB Users On the Settings / USB Storage / USB Users page, you can create user accounts to provide access to data on the USB storage connected to the router.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Samba On the Settings / USB Storage / Samba page, you can enable the built-in Samba server of the router to provide access to the USB storage for users of your LAN.
Page 137
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 113. Specifying a folder. In the opened window, locate a folder containing files. To do this, click the Search icon ( ) in the Path field.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual On the Settings / USB Storage / FTP page, you can enable the built-in FTP server of the router to provide access to the USB storage for users of your LAN.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Filebrowser On the Settings / USB Storage / Filebrowser page, you can view the content of your USB storage connected to the router and remove separate folders and files from the USB storage.
USB storage, or leave the value specified by default (900). In the DLNA server name field, specify a name of the DLNA server which will be displayed for users of your LAN or leave the value specified by default (D-Link DLNA Server). Use digits and/or Latin characters.
Page 141
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 117. Specifying a media folder. In the opened window, locate a folder containing files. To do this, click the Search icon ( ) in the Path field.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Torrent Client On the Settings / USB Storage / Torrent Client page, you can configure all needed settings for the built-in Transmission client.
Page 143
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Main Settings Port The router's port which will be used by the Transmission client. Locate data of the Transmission client. To do this, click the Search...
Page 144
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description The password to access the web-based interface of the Transmission Password client. After specifying the needed parameters, click the SAVE button.
Page 145
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Select the torrent file corresponding to the download which should be restarted and click the button. Start Selected Torrents Click the button to restart all downloads.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Settings / USB Modem This menu is designed to operate USB modems. Some models of USB modems do not allow performing operations available in this menu section through the web-based interface of the router.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Basic Settings On the Settings / USB Modem / Basic Settings page, you can view data on the USB modem...
Page 148
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Interface The network interface name. Revision The revision of the firmware of your USB modem. Serial number The unique identifier assigned to the device by its manufacturer.
Page 149
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual If upon one of the operations described above you have entered an incorrect value in the PIN code field three times (the number of remaining attempts is displayed in the PIN input window), the SIM card inserted into your USB modem is blocked.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual When a new text message is received, the relevant notification will be displayed in the top right corner of the page. Click the CHECK button. After clicking the button, the Settings / USB Modem / SMS page opens.
Page 151
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual To create and send a text message, click the CREATE MESSAGE button ( Figure 125. The window for creating a new text message.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual USSD On the Settings / USB Modem / USSD page, you can send a USSD command. USSD (Unstructured Supplementary Service Data) is a technology which provides real-time message exchange between a subscriber and a mobile operator's special application.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Functions / Firewall IP Filter On the Functions / Firewall / IP filter page, you can create new rules for filtering IP packets and edit or remove existing rules.
Page 154
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 129. The page for adding a rule for IP filtering. You can specify the following parameters: Parameter Description General Settings Move the switch to the right to enable the rule.
Page 155
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description A protocol for network packet transmission. Select a value from the Protocol drop-down list. An IP version to which the rule will be applied. Select the relevant IP version value from the drop-down list.
Page 156
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description End IPv4 address / The destination host end IPv4 or IPv6 address. End IPv6 address Subnet IPv4 address / The destination subnet IPv4 or IPv6 address.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual A DMZ is a host or network segment located “between” internal (local) and external (global) networks. In the router, the DMZ implements the capability to transfer a request coming to a port of the router from the external network to a specified host of the internal network.
Page 158
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual To set a schedule for the DMZ, click the Set schedule button ( ). In the opened window, you...
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual MAC Filter On the Functions / Firewall / MAC Filter page, you can configure MAC-address-based filtering for computers of the router's LAN.
Page 160
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In the opened window, you can specify the following parameters: Parameter Description Move the switch to the right to enable the rule.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual AdBlock On the Functions / Firewall / AdBlock page, you can enable the function of blocking advertisements which appear during web surfing.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Functions / Wi-Fi Client Management On the Functions / Wi-Fi / Client Management page, you can view the list of wireless clients connected to the router.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual On the Functions / Wi-Fi / WPS page, you can enable the function for configuration of the WLAN. The WPS function helps to configure the wireless network automatically. Devices connecting to the wireless network via the WPS function must support the WPS function.
Page 164
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual When the WPS function is enabled, the Information section is available on the page. Parameter Description The state of the WPS function: Configured (all needed settings are specified;...
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Using WPS Function via Web-based Interface To connect to the basic wireless network via the WPS function, follow the next steps: 1.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual On the Functions / Wi-Fi / WMM page, you can enable the Wi-Fi Multimedia function. The WMM function implements the QoS features for Wi-Fi networks. It helps to improve the quality of data transfer over Wi-Fi networks by prioritizing different types of traffic.
Page 167
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 137. The window for changing parameters of the WMM function. Parameter Description Arbitrary Inter-Frame Space Number. This parameter influences AIFSN time delays for the relevant Access Category.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Client On the Functions / Wi-Fi / Client page, you can configure the router as a client to connect to a wireless access point or to a WISP.
Page 169
When you have configured the parameters, click the APPLY button. When connecting to a wireless access point, the wireless channel of DIR-825 will switch to the channel of the access point to which you have connected. In addition, the Connection Information section in which you can view the connection status and the network basic parameters is displayed.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Client Shaping On the Functions / Wi-Fi / Client Shaping page, you can limit the maximum bandwidth of upstream and downstream traffic for each wireless client of the router by its MAC address.
Page 171
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In the opened window, you can specify the following parameters: Parameter Description Frequency band From the drop-down list, select a band of the wireless network.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Additional On page of the Functions / Wi-Fi / Additional section, you can define additional parameters for the WLAN of the router. To configure the 2.4GHz band or 5GHz band, go to the relevant tab.
Page 173
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual The following fields are available on the page: Parameter Description The channel bandwidth for 802.11n standard in the 2.4GHz band (the 2.4 GHz tab).
Page 174
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description The STBC (Space-time block coding) technique allows increasing data transfer reliability even for portable devices equipped with poor antennas (smartphones, pads, etc.) due to using several data streams...
Page 175
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description The time interval (in seconds) between keep alive checks of wireless devices from your WLAN. When the value 0 is specified, the Station Keep Alive checking is disabled.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual MAC Filter On the Functions / Wi-Fi / MAC Filter page, you can define a set of MAC addresses of devices which will be allowed to access the WLAN, or define MAC addresses of devices which will not be allowed to access the WLAN.
Page 177
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual You can specify the following parameters: Parameter Description Frequency band From the drop-down list, select a band of the wireless network.
Page 178
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual To change or delete the schedule for a rule, click the Select schedule button ( ) in the line corresponding to this rule.
In the Device name field, specify a name of the device for easier identification. You can specify any name. 15 At present, you can connect up to 6 D-Link devices with EasyMesh support: 1 in the Controller role and 5 in the Agent role.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual When you have configured the parameters, click the APPLY button. To complete your mesh network configuration, connect subordinate devices to the main device.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Connecting Subordinate Devices via Web-based Interface To connect a subordinate device with the ESTABLISH CONNECTION button in the web-based interface, follow the next steps: 1.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Functions / Advanced UPnP IGD On the Functions / Advanced / UPnP IGD page, you can enable the UPnP IGD protocol. The router uses the UPnP IGD protocol for automatic configuration of its parameters for network applications requiring an incoming connection to the router.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Remote Access On the Functions / Advanced / Remote Access page, you can configure access to the web- based interface of the router. By default, the access from external networks to the router is closed. If you need to allow access to the router from the external network, create relevant rules.
Page 184
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In the opened window, you can specify the following parameters: Parameter Description A name for the rule for easier identification. You can specify any Name name.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Virtual Servers On the Functions / Advanced / Virtual Servers page, you can create virtual servers for redirecting incoming Internet traffic to a specified IP address in the local area network.
Page 186
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 150. The page for adding a virtual server. You can specify the following parameters: Parameter Description General Settings Move the switch to the right to enable the server.
Page 187
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Select a virtual server template from the drop-down list, or select Template Custom to specify all parameters of the new virtual server manually.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual TR-069 Client On the Functions / Advanced / TR-069 Client page, you can configure the router for communication with a remote Auto Configuration Server (ACS).
Page 189
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Inform Settings Move the switch to the right so the router may send reports (data on the device and network statistics) to the ACS.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Static Route On the Functions / Advanced / Static Route page, you can specify static (fixed) routes. Figure 152. The Functions / Advanced / Static Route page.
Page 191
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In the opened window, you can specify the following parameters: Parameter Description Move the switch to the right to enable the route.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Dynamic DNS On the Functions / Advanced / Dynamic DNS page, ou can configure the router to use one or several DDNS services.
Page 193
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual On the opened page, you can specify the following parameters: Parameter Description Move the switch to the right to enable DDNS.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual IPsec On the Functions / Advanced / IPsec page, you can configure VPN tunnels based on IPsec protocol. IPsec is a protocol suite for securing IP communications.
Page 195
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual To create a new tunnel, click the ADD button ( ) in the Tunnels section. Setting for both devices which establish the tunnel should be the same.
Page 196
The field is available for editing if the Dynamic IPsec switch is moved to the left. A remote host identifier to establish connection over IPsec with particular hosts only. To establish connection, DIR-825 remote Remote identifier identifier value should correspond to the local identifier value specified in the settings of the remote host.
Page 197
• the default WAN connection. A local identifier of the router to establish connection over IPsec with particular hosts only. To establish connection, DIR-825 local identifier Local identifier value should correspond to the remote identifier value specified in the settings of the remote host. Use an IP address, domain name, or certificate CN.
Page 198
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description An operation mode of the IPsec tunnel. Select a value from the drop- down list. TUNNEL: As a rule, it is used to create a secure connection to •...
Page 199
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 158. The page for adding an IPsec tunnel. The First Phase / The Second Phase sections. Parameter Description...
Page 200
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Move the switch to the right to enable the aggressive mode for mutual Aggressive Mode authentication of the parties. Such a setting accelerates the connection establishment, but reduces its security.
Page 201
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 159. The page for adding an IPsec tunnel. The window for adding a tunneled network. In the opened window, you can specify the following parameters:...
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Ports Settings On the Functions / Advanced / Ports Settings page, you can configure or disable autonegotiation of speed and duplex mode or manually configure speed and duplex mode for each Ethernet port of the router.
Page 203
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 161. The window for changing the settings of the router's port. In the opened window, specify the needed parameters:...
Page 204
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Flow control Move the switch to the right to enable the flow control function for the port.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Redirect On the Functions/ Advanced / Redirect page, you can enable notifications on the reason of the Internet connection failure. Notifications will be displayed in the browser window when a user is attempting to open a web site on the Internet.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual IGMP/MLD On the Functions/ Advanced / IGMP/MLD page, you can allow the router to use IGMP and MLD and specify needed settings.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual ALG/Passthrough On the Functions/ Advanced / ALG/Passthrough page, you can allow the router to use RTSP, enable the SIP ALG and PPPoE/PPTP/L2TP/IPsec pass through functions.
Page 208
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual The following elements are available on the page: Parameter Description Move the switch to the right to enable SIP. Such a setting allows using the SIP ALG function.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Management System Time On the Management / System Time page, you can manually set the time and date of the router or configure automatic synchronization of the system time with a time server on the Internet.
Page 210
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual 3. Select your time zone from the Time zone drop-down list. To set the time zone in accordance with the settings of your operating system or portable device, click the DETERMINE TIMEZONE button.
Page 211
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual When the router is powered off or rebooted, the system time is reset to the default value. If you have set automatic synchronization for the system time, the internal clock of the device will be configured after connecting to the Internet.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual System Log On the Management / System Log page, you can set the system log options and configure sending the system log to a remote host and/or a USB storage connected to the router.
Page 213
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Logging Select a type of logging from the drop-down list. Local: the system log is stored in the router's memory. When •...
Page 214
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual To disable logging of the system events, move the Enable switch to the left and click the APPLY button.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Administration On the Management / Administration page, you can change the password for the administrator account used to access the web-based interface of the router and to access the device settings via...
Page 216
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual The following buttons are also available on the page: Control Description Click the button to restore the factory default settings. Also you can...
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Telnet/SSH On the Management / Telnet/SSH page, you can enable or disable access to the device settings via TELNET and/or SSH from your LAN. By default, access is disabled.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Yandex.DNS This menu is designed to configure the Yandex.DNS service. Yandex.DNS is a web content filtering service which provides the DNS server, protects a computer against malicious web sites, and blocks access to adult web sites.
Page 219
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Child: when this value is selected, the service blocks access to malicious and fraudulent • web sites and blocks access to adult content.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Devices and Rules On the Management / Yandex.DNS / Devices and Rules page, you can specify a filtering mode for each device separately.
Page 221
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In the opened window, you can specify the following parameters: Parameter Description The MAC address of a device from the router's LAN. You can enter...
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Firmware Update On the Management / Firmware Update page, you can update the firmware of the router and configure the automatic check for updates of the router's firmware.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Local Update Attention! Do not turn off the router before the firmware update is completed. This may cause the device breakdown.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Remote Update Attention! Do not turn off the router before the firmware update is completed. This may cause the device breakdown.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Schedule On the Management / Schedule page, you can enable/disable Wi-Fi connection and configure automatic reboot of the device on a schedule, and set a schedule for different filter rules.
Page 226
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In the opened window, in the System Time field, the system time of the device is displayed. You can select the Simplified mode choice of the radio button and specify the following parameters:...
Page 227
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual To set a schedule for a task which will be applied to a filter rule or will enable/disable Wi-Fi connection, click the ADD button ( ) in the All Tasks section.
Page 228
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Parameter Description Every week: When this value is selected, the names of days of the week and the Time field are displayed in the section.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Statistics The pages of this section display data on the current state of the router. Network Statistics On the Management / Statistics / Network Statistics page, you can view statistics for all connections existing in the system (WAN connections, LAN, WLAN).
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Port Statistics On the Management / Statistics / Port statistics page, you can view statistics for traffic passing through ports of the router. The information shown on the page can be used for diagnosing connection problems.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Routing The Management / Statistics / Routing page displays the routing rules and routing tables. Figure 179. The Management / Statistics / Routing page.
Page 232
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Figure 180. The routing table page. The opened page displays the information on routes in the selected routing table. The table contains destination IP addresses, gateways, subnet masks, and other data.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual DHCP The Management / Statistics / DHCP page displays the information on computers that have been identified by hostnames and MAC addresses and have got IP addresses from the DHCP server of the device.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Multicast Groups Management / Statistics / Multicast Groups page displays addresses of active multicast groups (including IPTV channels and groups for transferring service information) to which the device is subscribed, and the interface through which the device is subscribed.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Diagnostics Ping On the Management / Diagnostics / Ping page, you can check availability of a host from the local or global network via the Ping utility.
Page 236
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual To specify additional settings, click the MORE SETTINGS button. Figure 184. The Management / Diagnostics / Ping page. The additional settings window.
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual Traceroute On the Management / Diagnostics / Traceroute page, you can determine the route of data transfer to a host via the traceroute utility.
Page 238
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Configuring via Web-based Interface User Manual In the opened window, you can specify the following parameters: Parameter Description Specify the TTL (Time to live) parameter value. The default value is...
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Operation Guidelines User Manual CHAPTER 5. OPERATION GUIDELINES Safety Rules and Conditions Please carefully read this section before installation and connection of the device. Make sure that the power adapter and cables are not damaged.
RF noise in your home or office. To maximize your wireless range, follow the guidelines below. 1. Keep the number of walls and ceilings between the DIR-825 device and other network devices to a minimum – each wall or ceiling can reduce your wireless network range by 3- 90 feet (1-30 meters).
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Abbreviations and Acronyms User Manual CHAPTER 6. ABBREVIATIONS AND ACRONYMS Third Generation Access Category Advanced Encryption Standard Access Point Address Resolution Protocol BPSK Binary Phase-shift Keying...
Page 242
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Abbreviations and Acronyms User Manual ICMP Internet Control Message Protocol Identifier Internet Gateway Device IGMP Internet Group Management Protocol Internet Key Exchange IMEI International Mobile Equipment Identity...
Page 243
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Abbreviations and Acronyms User Manual Network Time Protocol OFDM Orthogonal Frequency Division Multiplexing Push Button Configuration Perfect Forward Secrecy Personal Identification Number Power over Ethernet...
Page 244
DIR-825 AC1200 Wave 2 MU-MIMO Wi-Fi EasyMesh Gigabit Router with 3G/LTE Support and USB Port Abbreviations and Acronyms User Manual SNMP Simple Network Management Protocol Secure Shell SSID Service Set Identifier STBC Space-time block coding Transmission Control Protocol TKIP Temporal Key Integrity Protocol...