Ferris 400S Series Operator's Manual
Zero-turn riding mower
Hide thumbs
Also See for 400S Series:
- Dealer setup & adjustment instructions manual (17 pages) ,
- Dealer service manual (44 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ferris 400S Series
Summary of Contents for Ferris 400S Series
- Page 1 Revision A...
-
Page 2: Table Of Contents
Table of Contents: Products Covered by This Manual........3 Product Identification Tag........... 3 CE Identification Tag Markings........... 3 Operator Safety..............3 Operating Safely...............4 Slope Identification Guide..........6 Safety Rules and Information...........6 Safety Decals..............9 Safety Decal Icon Definitions......... 11 Safety Icons for Optional Jack Kit Accessory....11 Safety Alert Symbol and Signal Words...... -
Page 3: Products Covered By This Manual
Record your model number, serial number, and engine model Turn Riding Mower. We’re pleased that you’ve placed and serial numbers in the space provided for easy access. your confidence in the Ferris brand. When operated and maintained according to the manuals, your Ferris product will PRODUCT REFERENCE DATA provide many years of dependable service. -
Page 4: Operating Safely
Operating Safely Children Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing deck is capable of amputating hands and feet and throwing objects. - Page 5 20.0 ft (6,0 m) length. Avoid turning down slopes; if possible Also, do not allow anyone in the area while the unit is running! turn up slopes. If someone does enter the area, shut the unit off immediately until they leave. Also note that the surface you are driving on can greatly impact stability and control.
-
Page 6: Slope Identification Guide
Slope Identification Guide General Operation 1. Read, understand, and follow all instructions in the manual and on the unit before starting. 2. Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. - Page 7 22. Always wear substantial footwear and trousers. Never operate when barefoot or wearing sandals. WARNING 23. Before using, always visually check that the blades and Unsafe Operation Hazard blade hardware are present, intact, and secure. Replace worn or damaged parts. Do not load this zero-turn rider on a trailer or truck using two separate ramps.
- Page 8 Emissions the edge of a cliff or ditch, or if an edge caves in. Give yourself a minimum of two mower widths of clearance 1. Engine exhaust from this product contains chemicals around these hazards. known, in certain quantities, to cause cancer, birth 11.
-
Page 9: Safety Decals
6. Never make adjustments or repairs with the engine fluid under high pressure. Use paper or cardboard, and running. not hands, to search for leaks. Make sure all hydraulic fluid connections are tight and all hydraulic hoses and 7. Check grass catcher components and the discharge lines are in good condition before applying pressure guard frequently and replace with manufacturer’s to the system. - Page 10 B.) Part Number: 7106109 - Decal, Discharge Safety, Export A.) Part Number: 5106566 - Decal, Main Safety - ZT (CE) C.) Part Number: 5061042 - Decal, CE Danger (Located under seat plate on cross rail.) ferrismowers.com...
-
Page 11: Safety Decal Icon Definitions
Safety Decal Icon Definitions J DANGER - THROWN OBJECTS AND AMPUTATION HAZARD: To avoid injury from rotating blades, stay clear of deck edge and keep others away. *This limit was determined per International Standard ISO 5395-3:2013, Section 4.6 and is based on the ISO 5395-3 Stability Test procedure described in Annex A. -
Page 12: Safety Interlock System Checks
Safety Interlock System Checks Zero-Turn Rider Controls WARNING DO NOT operate machine if any safety interlock or safety device is not in place and functioning properly. Contact your dealer immediately for assistance. DO NOT attempt to defeat, modify, or remove any safety device. TEST 1 - Engine must not crank if: •... - Page 13 Moving a lever forward (A) from the NEUTRAL position (B) increases the FORWARD speed of the associated wheel, and pulling back (C) on a lever increases the REVERSE speed. Moving a levers outwards (D) from the NEUTRAL position locks the levers in the NEUTRAL position. Note: The further a lever is moved away from the neutral position the faster the drive wheel will turn.
-
Page 14: Instrument Control Panel
Instrument Control Panel "A" - Hour Glass Icon - The hour glass icon flashes when the hour meter is recording the passage of time. "B" - Mode Icon - The mode icon will display an "E" when displaying engine hours, and a "P" when displaying PTO hours. -
Page 15: Operation
the parking brake. Pull the parking brake lever back, out away from the operator, and allow it to travel forward to disengage WARNING the parking brake. Do NOT load this zero-turn rider on a trailer or truck using two separate ramps. Only use a single ramp that is at least Note: To start the unit the parking brake must be engaged. ... -
Page 16: Stopping The Rider
5. After warming the engine always operate the unit at FULL throttle when mowing. In the event of an emergency the engine can be stopped by simply turning the ignition switch to STOP. Use this method only in emergency situations. For normal engine shut down follow the procedure given in Stopping the Rider. - Page 17 Reverse Travel Practice To turn in place, “Zero Turn,” gradually move one ground speed control lever forward from neutral and one lever back LOOK DOWN & BEHIND, then gradually move both ground from neutral simultaneously. Repeat several times. speed control levers evenly BACK from neutral. Slow down NOTE: Changing the amount each lever is pulled—forward or and repeat.
-
Page 18: Mowing
As you become more familiar and experienced with operating the Zero Turn rider, you will learn more maneuvers that will make your mowing time easier and more enjoyable. Remember, the more you practice, the better your control of the Zero Turn will be! Mowing 1. - Page 19 • Avoid mowing after rain or even heavy dew, and never The remainder of the mowing should be done in the opposite mulch when the grass is wet (moist grass does not mulch direction so that the clippings are dispersed OUT onto the well, and clumps beneath the mower deck).
-
Page 20: Pushing The Rider By Hand
The best mulching action typically results from cutting only rear of the rider and push it towards the rear tire. Repeat the top ½ inch to 3/4 inch of grass blade. This provides this process for the other side of the rider. short clippings which decompose properly (much more 4. -
Page 21: Adding Fuel
Adding Fuel Fuse Location and Identification The electrical system for this unit is equipped with two replaceable fuses. See the chart below for the circuit, WARNING amperage, and approximate location of the fuses. Fuel and its vapors are extremely flammable and explosive. ... -
Page 22: Checking Tire Pressures
Checking Tire Pressures Tire pressure should be checked periodically (see Figure 22), and maintained at the levels shown in the Specifications chart. Note that these pressures may differ slightly from the "Max Inflation" stamped on the side- wall of the tires. The pressures shown provide proper traction and extend tire life. ... -
Page 23: Cutting Height Adjustment
2. Place the cutting height adjustment pin (C) into the hole for the desired cutting height. Note: Make sure the pin is inserted into the holes in both upper and lower plates of the adjustment bracket (D). 3. Depress the deck lift foot pedal and then push the deck lift lock lever towards the right to release the lock. ... -
Page 24: Storage
the notch in the pre-load adjustment collar. While holding 6. Cover air cleaner and exhaust outlet tightly with plastic or the wrench in place with one hand, turn the pre-load other waterproof material to keep out moisture, dirt and adjustment collar to a higher notch (-) to decrease the insects. -
Page 25: Specifications
ZERO-TURN RIDER AND MOWER MAINTENANCE Tire Size 20 X 10 - 10 Inflation Pressure 12 psi (0,83 bar) Before each use Front Wheels Check the safety interlock system. Tire Size (Serial Number 11 X 4 - 5 Check the rider's brakes. 4000771923 and below) Check rider and mower for loose hardware. - Page 26 Briggs & Stratton products. ABOUT YOUR WARRANTY Warranty service is available only through Ferris Authorized Service Dealers. This warranty only covers defects in materials or workmanship. It does not cover damage caused ferrismowers.com...
- Page 27 Notes...
Need help?
Do you have a question about the 400S Series and is the answer not in the manual?
Questions and answers