Table of Contents
Advertisement
Quick Links
3PH - ENERGY METER
TECHNICAL MANUAL OF INSTALLATION
ENA3D
1 - BUTTONS AND INDICATION LEDs: ................................................................................ 2
2 - ELECTRICAL DIAGRAM FOR INSTALLATION: ............................................................... 2
3 - SET-UP MENU: ................................................................................................................... 3
4 - ENTER THE ALARMS MENU: ........................................................................................... 5
5 - MEASUREMENTS FUNCTIONS: ....................................................................................... 6
6 - TECHNICAL DATA: ............................................................................................................ 7
7 - TERMINAL CONNECTIONS: ............................................................................................. 8
8 - DIMENSIONS: ..................................................................................................................... 9
!!! IMPORTANT !!! READ THE INSTALLATION MANUAL BEFORE USE.
THE SAFETY OF THE PRODUCT IS STRICTLY RELATED TO ITS USE THAT HAS TO BE
DONE AS SPECIFIED BY THE MANIFACTURER.
INDEX
REGISTERS MODBUS-RTU TABLE ON REQUEST
ENA3
1 / 9
http://www.etigroup.eu/products-services
ETI d.d., Obrezija 5, SI-1411 Izlake
Advertisement
Table of Contents
Related Manuals for ETI ENA3D
Summary of Contents for ETI ENA3D
-
Page 1: Table Of Contents
!!! IMPORTANT !!! READ THE INSTALLATION MANUAL BEFORE USE. THE SAFETY OF THE PRODUCT IS STRICTLY RELATED TO ITS USE THAT HAS TO BE DONE AS SPECIFIED BY THE MANIFACTURER. 1 / 9 ETI d.d., Obrezija 5, SI-1411 Izlake http://www.etigroup.eu/products-services... -
Page 2: Buttons And Indication Leds
- Capacitive Load TEMP - Temperature (internal temperature sensor) 1-2-3 - Alarm Relay status - Multiplier measure x1000 - Multiplier measure x1000000 2 - ELECTRICAL DIAGRAM FOR INSTALLATION: 2 / 9 ETI d.d., Obrezija 5, SI-1411 Izlake http://www.etigroup.eu/products-services... -
Page 3: Set-Up Menu
) - Without transformer . For higher supply voltage than the supported range, insert one transformer each Phase and set with transformer ratio. 3 - SET-UP MENU: 3.1 ENTER THE BASIC SET-UP MENU: 3 / 9 ETI d.d., Obrezija 5, SI-1411 Izlake http://www.etigroup.eu/products-services... - Page 4 , an error has happened and was not possible to save the data. Therefore it will be necessary to program again all the parameters on the Advance Menu. Advance Set-up Menu: PAR. NAME DESCRIPTION RANGE DEFAULT 4 / 9 ETI d.d., Obrezija 5, SI-1411 Izlake http://www.etigroup.eu/products-services...
-
Page 5: Enter The Alarms Menu
. i) Press buttons to scroll Alarm values that can be set: > > > > (only for l) Press button to enter and change the desired Alarm values. 5 / 9 ETI d.d., Obrezija 5, SI-1411 Izlake http://www.etigroup.eu/products-services... -
Page 6: Measurements Functions
5 - MEASUREMENTS FUNCTIONS: IND CAP a) If the load are inductive or capacitive 6 / 9 ETI d.d., Obrezija 5, SI-1411 Izlake http://www.etigroup.eu/products-services... -
Page 7: Technical Data
=10 the average value is calculated on 20 seconds. After power on, during the first 15 minutes, the recording of the max values is disabled. 6 - TECHNICAL DATA: Supply Circuit 144x144 9 Modules 7 / 9 ETI d.d., Obrezija 5, SI-1411 Izlake http://www.etigroup.eu/products-services... -
Page 8: Terminal Connections
- IEC EN 61000-4-5 - IEC EN 61000-4-6 - IEC EN 61000-4-11 - IEC EN 61000-6-2 - IEC EN 61000-6-4 - IEC EN 61010-1 - IEC EN 61010-2-030 7 - TERMINAL CONNECTIONS: 8 / 9 ETI d.d., Obrezija 5, SI-1411 Izlake http://www.etigroup.eu/products-services... -
Page 9: Dimensions
CLEANING OF THE UNIT: If necessary clean the device with a soft cloth dampened with water. This operation must be done with the instrument switched off and disconnected from any power source. 9 / 9 ETI d.d., Obrezija 5, SI-1411 Izlake http://www.etigroup.eu/products-services...
Need help?
Do you have a question about the ENA3D and is the answer not in the manual?
Questions and answers