Related Manuals for Thermal Zone PAC9D
Summary of Contents for Thermal Zone PAC9D
- Page 1 950-0013-revE Dec. 26, 2006 Page 1 of 19...
-
Page 2: Table Of Contents
CONTENTS FOREWARD INTRODUCTION PART IDENTIFICATION CONTROL PANEL AND DISPLAY SCREEN REMOTE CONTROL CONTROL PANEL USE AND FUNCTIONS TIME SET FUNCTION WATER DRAINAGE METHODS MAINTENANCE AND SERVICE SAFETY TROUBLESHOOTING INSTALLATION SPECIFICATIONS WARRANTY Forward: Portable Air conditioners should be installed by a professional. Please read carefully the sections corresponding to the specific model you choose, and store the manual in a safe place, so as to facilitate your reference at a later time. -
Page 3: Introduction
MOBILE AIR CONDITIONER This Mobile Air Conditioner is a small size appliance, which can adjust the temperature and humidity in a room. Its flexibility characteristics make it easily used in different applications or in different rooms. It also has multiple functions, including cooling, dehumidifying and fan ventilation. -
Page 4: Part Identification
Page 4 of 19... -
Page 5: Control Panel And Display Screen
CONTROL PANEL DISPLAY (HEAT PUMP MODEL ONLY) DISPLAY (COOL ONLY MODEL) Page 5 of 19... -
Page 6: Remote Control
IF REMOTE IS LOST: Unplug unit for 10 seconds, then reconnect power. Unit will now function via the control panel. Page 6 of 19... -
Page 7: Control Panel Use And Functions
POWER SOURCE • The AC outlet must be a 3 prong grounded outlet using the provided LCDI power cord. • Do not connect the portable air conditioner to a multiple socket outlet which is also being used for other electrical appliances. •... -
Page 8: Time Set Function
ALWAYS REMOVE POWER (Heat Pump Models Only) 1. Repeatedly press the MODE button to select the heat mode, The LCD window shows ''HEAT''. 2. Press the TEMP + or TEMP - button to set a proper room temperature Range. 63°F-88°F (17° to 31° C) . 3. - Page 9 Condensation – Water Removal This Portable Air conditioner is designed to evaporate the condensation removed from the interior area. Under certain conditions it is not possible that the unit will evaporate 100% of the removed moisture. As the unit accumulates condensation, under normal condition, it will be evaporated through the exhaust hose.
-
Page 10: Maintenance And Service
ALWAYS REMOVE POWER FROM UNIT BEFORE SERVICING CLEANING THE AIR FILTER For more efficient operation air filter must be cleaned regularly. Performance of this unit is highly affected by a clogged air filter. Air filter should be cleaned every 2 weeks of operation or sooner if necessary. To remove the air filter: 1. -
Page 11: Safety
AFTER SEASONAL OPERATION After the operational season or when the unit is to be stored, You should: 1. Turn off the air conditioner and remove the power source. 2. Clean Air Filter and outside of unit as explained earlier. 3. Open the Drain at the bottom rear of the unit. 4. -
Page 12: Troubleshooting
IF YOU ARE HAVING TROUBLE WITH THE OPERATION OF THIS UNIT PLEASE CHECK THE FOLLOWING BEFORE SEEKING REPAIR OR SERVICE. TROUBLE CHECK ACTION Air conditioner does Is there power to the unit? Verify power to unit. not operate at all. Is it plugged in? Plug unit into the wall Did the Circuit breaker or... -
Page 13: Installation
SELECTION OF INSTALLATION LOCATION Place the Portable air conditioner in a flat location where the air outlets are not blocked. Place the unit at least 20” (500mm) from walls or other obstacles. INSTALLING THE AIR INLET AND EXHAUST HOSES 1. Fit one end of the exhaust hose to the exhaust port on the unit. Turn 2- 3 full turns to tighten the hose. - Page 14 INSTALLING THE EXHAUST HOSE If the hose becomes shredded at the end, you may cut the damaged section off and re-install as before. Correct mounting shown below, see Fig. 1 Fig.2& Fig.3. If mounting in the wall the height of the hole should be between 16” and 51”(400mm-1300mm) Note: There two exhaust hoses of this unit, their installations are same.
- Page 15 If the air exhaust requires bending, please see the diagrams below. Incorrect Hose Mounting Fig. 4 (Air exhaust bend too large). Page 15 of 19...
- Page 16 Window Kit Installation Your Window Kit has been designed to fit most standard “Vertical” and “Horizontal” window applications. However, it may be necessary for you to improvise/modify some aspects of the installation procedures for certain types of windows. Please refer to Fig. 5 & Fig.6 for minimum and maximum window openings INSTRUCTIONS: Install (2) screws on to installation board II as shown below.
- Page 17 INSTALLATION ACCESSORIES (FIG.7) DESCRIPTION Flexible Exhaust hose with adapters …………………. (1) (Kit contains 2 hoses and 2 adapters) Stretches from 19-1/2” (500 mm) to 78-3/4” (2000mm) Window Exhaust adapter kit ……………………………..(1) 2 pieces in kit Adjustable window slider kit ……………………………..(1) Fits windows from 26-5/8”...
-
Page 18: Specifications
Product Specifications PORTABLE AIR CONDITIONER PAC9D MODEL 9000 BTU COOLING CAPACITY HEATING CAPACITY IP20 WATERPROOF TYPE ELECTRIC SHOCK PROTECTION CLASS 115 VAC RATED VOLTAGE 60 Hz RATED FREQUENCY 1260 WATTS COOLING POWER INPUT 11.2 AMPS COOLING CURRENT INPUT HEATING POWER INPUT... -
Page 19: Warranty
WARRANTY International Refrigeration Products warrants that the product supplied is free from defects in material and workmanship. This warranty is valid as long as this product is properly handled, installed, operated and serviced in accordance with the Installation and Operating Instructions shipped with this unit, and warranty card is completed and mailed no later than 30 days after date of purchase.
Need help?
Do you have a question about the PAC9D and is the answer not in the manual?
Questions and answers