Table of Contents
Advertisement
TK-7108
3-3. KPG-46 Description
(PC programming interface cable : Option)
The KPG-46 is required to interface the TK-7108 to the
computer. It has a circuit in its D-subconnector (25-pin) case
that converts the RS-232C logic level to the TTL level.
The KPG-46 connects the modular microphone jack of
the TK-7108 to the computers RS-232C serial port.
3-4. Programming Software Description
The KPG-70D programming disk is supplied in 3-1/2" disk
format. The software on this disk allows a user to program
TK-7108 radio via a programming interface cable (KPG-46).
3-5. Programming With IBM PC
If data is transferred to the transceiver from an IBM PC
with the KPG-70D, the destination data (basic radio informa-
tion) for each set can be modified.
4. Clone Mode
Programming data can be transferred from one radio to
another by connecting them via their modular microphone
jacks. The operation is as follows (the transmit radio is the
master and the receive radio is the slave).
NOTE: Clone mode should enabled.
1. Turn the master TK-7108 power ON with the [1] key held
down. The TK-7108 [ ] LED is turned on.
2. Power on the slave TK-7108.
3. Connect the cloning cable (No. E30-3382-05) to the
modular microphone jacks on the master and slave.
4. Press the [ ] key on the master TK-7108 transceiver. The
data of the master is sent to the slave. While the master
is sending data, [TX] LED blinked. While the slave is re-
ceiving the data, 4 LEDs, [MON] LED, [ ] LED are turned
on and [BUSY] LED blinked. When cloning of data is com-
pleted, the master [TX] LED turned off, and the slave au-
tomatically operates in the User mode. The slave can
then be operated by the same program as the master.
5. The other slave can be continuously cloned. Carry out
the operation in step 2 to 4.
12
REALIGNMENT / 模式组合
IBM-PC
KPG-70D
Fig. 1 / 图1
3-3. KPG-46说明
(计算机编程电缆：可选件)
KPG-46用于将TK-7108与计算机连接。在其D型副插座 (25
芯)中有一个电平转换电路，此电路可以把RS-232C逻辑电平转
换为TTL电平。
KPG-46将TK-7108的话筒插座与计算机的RS-232C串行口连
接。
KPG-46
TK-7108
3-4. 编程软件说明
KPG-70D编程软盘是一张3-1/2" 软盘。软盘内的软件允许用
户经由编程电缆 (KPG-46) 对TK-7108进行编程设定。
3-5. 使用IBM计算机编程
如果从使用KPG-70D磁盘的IBM计算机将数据发送到车载
台，设定的目的数据 (通信机的基本参数)均可被修改。
4. 复制模式
可以利用标准话筒插孔连接从一台通信机向另一台通信机传
送编程数据。按照下述步骤操作 (发射方车载台为主机，接收
方车载台为子机).
注释: 启用复制模式。
1. 按住[1]键打开主 TK-7108的电源，TK-7108的[ ]指示灯亮。
2. 开启子机TK-7108的电源.
3. 将数据复制电缆(No. E30-3382-05)连接到主机及从属机的标
准话筒插孔。
4. 按主TK-7108通信机的[ ]键。主机的数据将发送到从属机。
主机发送数据时[TX]指示灯闪烁。从属机接收数据时 4 个指
示灯、[MON]指示灯及[ ]指示灯亮，[BUSY]指示灯闪烁。
数据复制完成后，主机的[TX]指示灯关闭，从属机自动运行
于用户模式。之后，从属机即可由与主机相同的程序操作。
5. 另一台子机可以继续复制。进行步骤2到4的操作。
Advertisement
Table of Contents
