Kenwood TK-5210 Service Manual page 7

TK-5210
■ Clone operation depending on hardware and
firmware versions
When Clone is executed between transceivers using
different versions of hardware and firmware, the Clone
operation is as follows.
•
Cloning between transceivers using hardware version 1
Source transceiver
(Hardware version 1.0)
Firmware Version
~V1.04
V1.05~V2.99
•
Cloning from hardware version 1 to hardware version 2
Source transceiver
(Hardware version 1.0)
Firmware Version
~V1.04
V1.05~V2.99
Note:
Under certain conditions, cloning cannot be performed
even if you are using a proper hardware and firmware
combination. Refer to the FPU for more details.
8. Self Programming Mode
(K2 and K3 models only)
Write mode for frequency data and signaling etc. To be
used ONLY by the authorized service person maintaining the
user's equipment. After programming, reset the FPU to the
"Self- Programming" disabled mode. Transceivers CANNOT
be delivered to the end-user in the self-programming mode.
The following setup items in the channels programmed by
the FPU can be changed using the self-programming mode.
The addition of new channel and the deletion of channel that
has already been programmed by the FPU cannot be
performed using the self-programming mode.
The setup items for self programming mode are as follows.
No. Setup item
1 Select
Zone/Channel
2 RX frequency
3 TX frequency
4 Channel type
5 TX mode
6 Channel spacing
7 RX Signaling
8 TX Signaling
9 RX NAC
10 TX NAC
11 Talkgroup list number
6
REALIGNMENT
Target transceiver
(Hardware version 1.0)
operation
Firmware Version
~V1.04
→
V1.05~V2.99
~V1.04
→
V1.05~V2.99
Yes : Cloning is possible
No : Cloning is not possible
Target transceiver
(Hardware version 2.0)
operation
Firmware Version
→
F3.00~
→
F3.00~
Yes : Cloning is possible
No : Cloning is not possible
Display
ZONE [**] -CH ***
ZONE ** -CH [***]
RX Freq
TX Freq
CH Type
TX Mode
CH Space
RX Sig
TX Sig
RX NAC ***
TX NAC ***
TG List No. ***
• RX frequency
• TX frequency
• Channel type
• TX mode (When the channel type is selected "MIXED".)
• Channel spacing
• RX signaling
• TX signaling
• RX NAC
• TX NAC
Clone
• Talkgroup list number
Note:
Yes
The personality will be also changed when the above-
No
mentioned items is changed. (Refer to the FPU for the
No
personality details.)
Yes
Key guide on the "INPUT PASSWORD" display.
• CNF([A] key): The password confirmation
• DEL([B] key): Delete the least digit from the current pass-
• SET([D] key): Determine the least digit of the password
Clone
8-1. Enter to the self programming mode
No
Press and hold the [Side2] and [PTT] keys while turning
Yes
the transceiver power ON and then release the [PTT] key
first. Ignoring whether the Read authorization password is
set or not, "INPUT PASSWORD" appears.
If the Read authorization password is not set to the trans-
ceiver, "SELF PROG MODE" is displayed on the LCD when the
[A] key is pressed while "INPUT PASSWORD" is displayed.
If the password is set to the transceiver, "SELF PROG
MODE" is displayed on the LCD when you enter the correct
password while "INPUT PASSWORD" is displayed.
For the password input method, see "7. Clone Mode"
step 3 described on page 5.
Note :
This mode (self programming mode) cannot be set when
it has been disabled with the FPU.
8-2. Data Writing
If the [Side3] key is pressed while Zone/Channel mode is
displayed, new data is written into memory. "Writing" is dis-
played while the transceiver is writing data.
Zone : 1~50
CH : 1~250
Receive frequency
Transmit frequency
ANALOG/P25/MIXED
ANALOG/P25
25.0kHz/12.5kHz (When the Channel type is selected "ANALOG" or "MIXED".)
P25 12.5kHz/12.5kHz (When the Channel type is selected "P25".)
Receive QT/DQT
Transmit QT/DQT
000~FFF (Hexadecimal)
000~FFF (Hexadecimal)
1~250
word number (Press and hold to delete all
password numbers)
number
Remarks
Note : "F7F" cannot be set.
Note : "F7E" and "F7F" cannot be set.