Summary of Contents for Nordson Pro-Meter S Series
Page 1
Dispensers with Integrated Drive Customer Product Manual Part 1606702-05 Issued 10/20 For parts and technical support, call the Nordson Industrial Coating Systems Customer Support Center at (800) 433−9319, or contact your local Nordson Representative. This document is subject to change without notice.
........Contact Us Notice This is a Nordson Corporation publication which is protected by copyright. Nordson Corporation welcomes requests for information, comments, and Original copyright date 2015. No part of this document may be inquiries about its products.
Page 3
Change Record Revision Date Change 9/15 New release 3/18 Removed part number 1084754, changed ft−lb spec on page 23 8/18 Added anti-drool dispense gun 10/20 Update to current product line 10/20 Added E-Net Dispensers Part 1606702-05 E 2020 Nordson Corporation...
Page 4
Change Record Part 1606702-05 E 2020 Nordson Corporation...
Do not restart the equipment until the Intended Use problem has been identified and corrected. Use of Nordson equipment in ways other than those Obtain and read Safety Data Sheets (SDS) for all described in the documentation supplied with the materials used.
Injection in the skin is a serious traumatic injury. It is Use only replacement parts that are designed for use important to treat the injury surgically as soon as with original equipment. Contact your Nordson possible. Do not delay treatment to research toxicity. representative for parts information and advice.
A packing gland and plunger rod is mounted to the metering cylinder. The plunger rod displaces material when the actuator extends. Cord set—Cable connection to system controller or J-box for electric heater functions Part 1606702-05 E 2020 Nordson Corporation...
Page 8
Packing Gland Type Temperature Conditioned (T/C) Standard and ARW E−Net Only S100 Standard S300 Standard 120 V Standard Standard S100 Standard S165 Standard S300 Standard 240 V Standard Standard S100 Standard S165 Standard S300 Standard Part 1606702-05 E 2020 Nordson Corporation...
Open metering cylinder. The material outlet valve opens at the same time and material extrudes proportionally to the given input signal. FROM INLET VALVE TO OUTLET VALVE REFILL PRE-PRESSURE/IDLE DISPENSE/PURGE Figure 2 Metering Cylinder Part 1606702-05 E 2020 Nordson Corporation...
Maximum Fluid 206 bar (3000 psi) Working Pressure 110 bar (1600 psi) Maximum Continuous Fluid Output Note: Contact the Nordson Automotive Systems Group Engineering department if higher fluid Pressure output pressures are required. 5 cc/sec 10 cc/sec 20 cc/sec 40 cc/sec...
GUN CLOSE AIR 1/4 TUBE GUN CLOSE AIR 1/4 TUBE GUN OPEN AIR 1/4 TUBE MATERIAL INLET AUTO-FLO GUN PORTS 9/16-18 SAE NOZZLE NUT INLET VALVE 3/8 NPS THD Figure 3 S15 Heated Dispenser Part 1606702-05 E 2020 Nordson Corporation...
GUN CLOSE AIR 1/4 TUBE GUN CLOSE AIR 1/4 TUBE GUN OPEN AIR 1/4 TUBE MATERIAL INLET AUTO-FLO GUN PORTS 9/16-18 SAE NOZZLE NUT INLET VALVE 3/8 NPS THD Figure 4 S35 Heated Dispenser Part 1606702-05 E 2020 Nordson Corporation...
Page 13
GUN CLOSE AIR 1/4 TUBE GUN OPEN AIR 1/4 TUBE MATERIAL INLET PORTS 9/16-18 SAE AUTO-FLO GUN INLET VALVE NOZZLE NUT 3/8 NPS THD Figure 5 S35 Heated E-Net Dispenser (240V heated dispenser shown) Part 1606702-05 E 2020 Nordson Corporation...
Page 14
AIR 1/4 TUBE GUN OPEN AIR 1/4 TUBE MATERIAL INLET AUTO-FLO GUN PORTS 9/16-18 SAE INLET VALVE NOZZLE NUT 3/8 NPS THD Figure 6 S35 T/C and T/C ARW E-Net Dispensers (T/C dispenser shown) Part 1606702-05 E 2020 Nordson Corporation...
20.83 cm. AIR 1/4 TUBE GUN CLOSE AIR 1/4 TUBE GUN OPEN AIR 1/4 TUBE MATERIAL INLET AUTO-FLO GUN PORTS 9/16-18 SAE NOZZLE NUT INLET VALVE 3/8 NPS THD Figure 7 S100 Heated Dispenser Part 1606702-05 E 2020 Nordson Corporation...
Page 16
VALVE CLOSE AIR 1/4 TUBE GUN CLOSE AIR 1/4 TUBE GUN OPEN AIR 1/4 TUBE MATERIAL INLET PORTS 9/16-18 SAE AUTO-FLO GUN INLET VALVE NOZZLE NUT 3/8 NPS THD Figure 8 S100 Heated E-Net Dispenser Part 1606702-05 E 2020 Nordson Corporation...
Page 17
AIR 1/4 TUBE PORTS 1/4 TUBE GUN CLOSE AIR 1/4 TUBE GUN OPEN AIR 1/4 TUBE MATERIAL INLET AUTO-FLO GUN PORTS 9/16-18 SAE INLET VALVE NOZZLE NUT 3/8 NPS THD Figure 9 S100 T/C E-Net Dispenser Part 1606702-05 E 2020 Nordson Corporation...
19.95 cm. GUN CLOSE 9.820 in. AIR 1/4 TUBE 24.94 cm. GUN OPEN AIR 1/4 TUBE MATERIAL INLET AUTO-FLO GUN PORTS 9/16-18 SAE NOZZLE NUT INLET VALVE 3/8 NPS THD Figure 10 S165 Heated Dispenser Part 1606702-05 E 2020 Nordson Corporation...
Page 19
VALVE CLOSE AIR 1/4 TUBE GUN CLOSE AIR 1/4 TUBE GUN OPEN AIR 1/4 TUBE MATERIAL INLET AUTO-FLO GUN PORTS 9/16-18 SAE INLET VALVE NOZZLE NUT 3/8 NPS THD Figure 11 S165 Heated E-Net Dispensers Part 1606702-05 E 2020 Nordson Corporation...
ø .015 A B C 15.479 in. [39.316 cm] MATERIAL OUTLET PORT 1-1/16-12 SAE PRESSURE TRANSDUCER PORTS 7/16−20 SAE BOTH SIDES MATERIAL INLET PORT 1-1/16−12 SAE BOTH SIDES Figure 12 S300 T/C E-Net Dispenser Part 1606702-05 E 2020 Nordson Corporation...
Engineering if the dispenser needs to be oriented in before installing a Pro-Meter S-Series dispenser into a different way that’s not shown. a system. Contact a local Nordson representative regarding these procedures if necessary. Do not install the dispenser with the outlet port positioned to the side.
(11) on the outlet valve (9). to the controller. 4. Connect the air lines from the pneumatic control valve to the Gun Open fitting (6) and Gun Close fitting (7) on the inlet valve (8). Figure 14 Typical Connections Part 1606702-05 E 2020 Nordson Corporation...
NOTE: Operation of the Pro-Meter Series-S meter is dependent upon the system configuration. Refer to the system manual that shipped with the system or contact a Nordson representative for information about the operation of a specific component. Part 1606702-05 E 2020 Nordson Corporation...
(A) Small amounts of weepage may indicate a potential problem but will not affect dispensed material accuracy. Investigate and repair any weepage as soon as possible. Excessive leakage caused by blown O-rings or loose fittings will affect dispensed material accuracy and must be immediately repaired. Part 1606702-05 E 2020 Nordson Corporation...
Follow the safety problems that you may encounter. If you cannot solve the problem with the information given here, contact your instructions in this document and all other related local Nordson representative for help. documentation. Problem Possible Cause...
Item Part Application WARNING: Read and understand this entire section before performing repairs. Contact a Never-Seez 900344 Nordson representative regarding these Thread locking 900464 Apply to threads of procedures if necessary. Review the following: Adhesive applicable parts. Allow only qualified personnel to perform...
(8). Tighten the screws to 13.5 N•m (10 ft-lb ). 7. Install the shroud (13) to the linear actuator (1) and housing flange (9). Install the washers (12) and screws (11). Tighten the screws securely. Part 1606702-05 E 2020 Nordson Corporation...
Refill Proximity sections for the adjustment 5. Perform the following: procedures. a. Install the anti-rotate arm (17) onto the shaft (19) in the orientation shown. Thread the coupling (16) into the shaft. Tighten the coupling finger tight. Part 1606702-05 E 2020 Nordson Corporation...
Page 29
5 CC PROXIMITY SENSOR SETTING 10 CC PROXIMITY SENSOR SETTING 20, 21 11, 12 15 CC PROXIMITY SENSOR SETTING Figure 15 Linear Actuator and Proximity Sensor Repairs Note: Standard dispenser shown. E-Net dispensers do not use proximity sensors. Part 1606702-05 E 2020 Nordson Corporation...
4. Connect the cable to the proximity sensor. 5. See Figure 15. Install the shroud (13) to the linear actuator (1) and housing flange (9) using the washers (12) and screws (11). Tighten the screws securely. Part 1606702-05 E 2020 Nordson Corporation...
Page 31
ARM STOP PIN sensors, push the arm toward the sensor to REFILL PROXIMITY SENSOR remove backlash. PROXIMITY DISC (NORMALLY OPEN) JAM NUT (TYPICAL) 1.0−1.5 mm (0.040−0.060) EXTEND PROXIMITY SENSOR (NORAMLLY CLOSED) Figure 16 Proximity Sensor Adjustment Part 1606702-05 E 2020 Nordson Corporation...
Replace damaged O-rings. 5−5.6 N•m (45−50 in.-lb). 5. Lubricate the O-rings (13) with TFE grease and install them into the housing (1). 4. Connect the cable to pressure transducer (2). Part 1606702-05 E 2020 Nordson Corporation...
Page 33
Pro-Meter S-Series Coupled Dispensers with Integrated Drive Figure 17 Inlet and Outlet Valve Repair Part 1606702-05 E 2020 Nordson Corporation...
(5) using the lock washers (3) and plunger (12). screws (4). Tighten the screws securely. 12. Clean the parts with a compatible solvent. 13. Inspect the parts for wear and damage. Replace parts if necessary. Part 1606702-05 E 2020 Nordson Corporation...
Page 35
Pro-Meter S-Series Coupled Dispensers with Integrated Drive FIGURE 19, 20 3, 4 Figure 18 Plunger and Gland Assembly Repairs Note: Standard dispenser shown. E-Net dispensers do not use proximity sensors. Part 1606702-05 E 2020 Nordson Corporation...
Using the press, push out the internal parts (3). 3. Thoroughly clean the packing gland housing in a compatible solvent to remove all sealant material and O-ring debris. Part 1606702-05 E 2020 Nordson Corporation...
Page 37
Pro-Meter S-Series Coupled Dispensers with Integrated Drive SCRAPER RING SHARP EDGE DOWN BRASS SEAL RETAINER SLIGHTLY PACKING GLAND HOUSING BELOW PACKING GLAND HOUSING Figure 19 Replacing the Internal Parts of the Packing Gland Part 1606702-05 E 2020 Nordson Corporation...
(12) using the screws (14) tighten the screws securely. 9. Install the side cover (6) onto the heater box (12) using the screws (5). Tighten the screws securely. Figure 20 Replacing the Thermostat Part 1606702-05 E 2020 Nordson Corporation...
Pro-Meter S-Series Coupled Dispensers with Integrated Drive Parts To order parts, call the Nordson Customer Service Center or your local Nordson representative. NOTE: E-Net dispenser parts begin on page 52. Standard Dispensers The following standard dispensers are available. S15 120 Volt Heated Dispenser See Figures 22 and 23.
Page 41
Pro-Meter S-Series Coupled Dispensers with Integrated Drive Figure 23 S15 120 Volt Heated Dispenser Parts (Continued) Part 1606702-05 E 2020 Nordson Corporation...
Page 42
S SCREW, socket, M8 x 45 − − − − − − S GLAND ASSEMBLY, tri-lip, 0.75 d 981907 S SCREW, drive, 4 x 0.250 982031 S SCREW, socket, M6 x 25 1070490 S FLANGE, housing, plunger Continued... Part 1606702-05 E 2020 Nordson Corporation...
Page 43
C: Refer to the applicable wiring diagram to order these parts. D: Refer to the Kits section to order this part. E: See Figure 21 for jumper wire location. AR: As Required NS: Not Shown Part 1606702-05 E 2020 Nordson Corporation...
See Figures24 and 25. Refer to the parts list that begins on page 42. FIGURE 18, 19 PART OF 9 THESE PARTS ARE APPLICATION SPECIFIC. THESE PARTS ARE INCLUDED WITH GUN OR MANIFOLD. Figure 24 S35 120 Volt Heated Dispenser Parts Part 1606702-05 E 2020 Nordson Corporation...
Page 45
Pro-Meter S-Series Coupled Dispensers with Integrated Drive Part 1606702-05 E 2020 Nordson Corporation...
Page 46
S SCREW, socket, M8 x 45 − − − − S GLAND ASSEMBLY, tri−lip, 0.75 d 981907 S SCREW, drive, 4 x 0.250 982031 S SCREW, socket, M6 x 25 1070490 S FLANGE, housing, plunger Continued... Part 1606702-05 E 2020 Nordson Corporation...
Page 47
B: These parts are included with 15A but can be ordered separately. C: Refer to the applicable wiring diagram to order these parts. D: Refer to the Kits section to order this part E: See Figure 21 for jumper wire location. AR: As Required Part 1606702-05 E 2020 Nordson Corporation...
See Figures 26 and 27. Refer to the parts list that begins on page 46. FIGURE 18, 19 PART OF 9 THESE PARTS ARE APPLICATION SPECIFIC. THESE PARTS ARE INCLUDED WITH GUN OR MANIFOLD. Figure 26 S100 120 Volt Heated Dispenser Parts Part 1606702-05 E 2020 Nordson Corporation...
Page 49
Pro-Meter S-Series Coupled Dispensers with Integrated Drive Figure 27 S100 120 Volt Heated Dispenser Parts (Continued) Part 1606702-05 E 2020 Nordson Corporation...
Page 50
S SCREW, socket, M5 x 30 984155 S NUT, panel mounting 1606153 S CORD SET, 120V 973543 S PLUG, O-ring, 7/16−20 1078538 S HEATER CARTRIDGE, 0.38 d x 5.75, 120 v, 150 w Continued... Part 1606702-05 E 2020 Nordson Corporation...
Page 51
B: These parts are included with 15A but can be ordered separately. C: Refer to the applicable wiring diagram to order these parts. D: See Figure 21 for jumper wire location. AR: As Required Part 1606702-05 E 2020 Nordson Corporation...
See Figures 28 and 29. Refer to the parts list that begins on page 50. FIGURE 18, 19 PART OF 9 THESE PARTS ARE APPLICATION SPECIFIC. THESE PARTS ARE INCLUDED WITH GUN OR MANIFOLD. Figure 28 S165 120 Volt Heated Dispenser Parts Part 1606702-05 E 2020 Nordson Corporation...
Page 53
Pro-Meter S-Series Coupled Dispensers with Integrated Drive Figure 29 S165 120 Volt Heated Dispenser Parts (Continued) Part 1606702-05 E 2020 Nordson Corporation...
Page 54
S SCREW, socket, M5 x 30 984155 S NUT, panel mounting 1606153 S CORD SET, 120V 973543 S PLUG, O-ring, 7/16−20 129642 S HEATER CARTRIDGE, 0.38 d x 5.75, 120 v, 150 w Continued... Part 1606702-05 E 2020 Nordson Corporation...
Page 55
B: These parts are included with 15A but can be ordered separately. C: Refer to the applicable wiring diagram to order these parts. D: See Figure 21 for jumper wire location. AR: As Required Part 1606702-05 E 2020 Nordson Corporation...
See Figures 30, 31, 32, and the following parts list that begins on page 54. ONLY USED ON 240 V DISPENSER PART OF 15 THESE PARTS ARE APPLICATION SPECIFIC. THESE PARTS ARE INCLUDED WITH GUN OR MANIFOLD. Figure 30 S35 120/240 Heated E-Net Dispenser Parts Part 1606702-05 E 2020 Nordson Corporation...
Page 57
Pro-Meter S-Series Coupled Dispensers with Integrated Drive GND TERMINAL FROM CORDSET Figure 31 S35 120/240 Volt Heated E-Net Dispenser Parts (Continued) Part 1606702-05 E 2020 Nordson Corporation...
Page 58
− − − − − − − − S WASHER, lock, M, internal, M3, per ISO 7079 − − − − − − − − S SCREW, socket, M3 x 6, per ISO 4762 Continued... Part 1606702-05 E 2020 Nordson Corporation...
Page 59
120VOLT CIRCUIT 240 VOLT CIRCUIT HEATER CATRIDGE HEATER CATRIDGE HEATER CATRIDGE HEATER CATRIDGE HEATER CATRIDGE HEATER CATRIDGE HEATER CATRIDGE HEATER CATRIDGE Î CORDSET Î CORDSET Figure 32 S35 120/240 Volt Heated E-Net Dispenser Parts (Continued) Part 1606702-05 E 2020 Nordson Corporation...
S35 Temperature Controlled E-Net Dispenser See Figure 33 and the following parts list. PART OF 22 THESE PARTS ARE APPLICATION SPECIFIC. THESE PARTS ARE INCLUDED WITH GUN OR MANIFOLD. Figure 33 S35 Temperature Controlled E-Net Dispenser Parts Part 1606702-05 E 2020 Nordson Corporation...
Page 61
NOTE A: Refer to the Kits section to order this part. B: These parts are included with 13A but can be ordered separately. C: The pressure transducer is application specific: 1000 psi: Order 1085753 3000 psi: Order 1084752 AR: As Required NS: Not Shown Part 1606702-05 E 2020 Nordson Corporation...
Pro-Meter S-Series Coupled Dispensers with Integrated Drive S35 ARW Temperature Conditioned E-Net Dispenser See Figure 34 and the following parts list. PART OF 24 THIS PART IS APPLICATION SPECIFIC. Figure 34 S35 ARW E-Net Dispenser Parts Part 1606702-05 E 2020 Nordson Corporation...
Page 63
NOTE A: Refer to the Kits section to order this part. B: These parts are included with 14A but can be ordered separately. C: The pressure transducer is application specific: 1000 psi: Order 1085753 3000 psi: Order 1084752 AR: As Required NS: Not Shown Part 1606702-05 E 2020 Nordson Corporation...
See Figures 35, 36, 37, and the parts list that begins on page 62. ONLY USED ON 240 V DISPENSER PART OF 13 THESE PARTS ARE APPLICATION SPECIFIC. THESE PARTS ARE INCLUDED WITH GUN OR MANIFOLD. Figure 35 S100 120/240 V Heated E-Net Dispenser Parts Part 1606702-05 E 2020 Nordson Corporation...
Page 65
Pro-Meter S-Series Coupled Dispensers with Integrated Drive GND TERMINAL FROM CORDSET Figure 36 S35 120/240 Volt Heated E-Net Dispenser Parts (Continued) Part 1606702-05 E 2020 Nordson Corporation...
Page 66
− − − − − − − − S WASHER, lock, M, internal, M3, per ISO 7079 − − − − − − − − S SCREW, socket, M3 x 6, black, per ISO 4762 Continued... Part 1606702-05 E 2020 Nordson Corporation...
Page 67
D: See Figure 37 for ferrule location. AR: As Required NS: Not Shown 120 VOLT CIRCUIT 240 VOLT CIRCUIT HEATER CATRIDGE HEATER CATRIDGE HEATER CATRIDGE HEATER CATRIDGE CORDSET CORDSET Figure 37 S35 120/240 Volt Heated E-Net Dispenser Parts (Continued) Part 1606702-05 E 2020 Nordson Corporation...
S100 Temperature Conditioned E-Net Dispenser See Figure 38 and the following parts list. PART OF 22 THESE PARTS ARE APPLICATION SPECIFIC. THESE PARTS ARE INCLUDED WITH GUN OR MANIFOLD. Figure 38 S100 Temperature Conditioned E-Net Dispenser Parts Part 1606702-05 E 2020 Nordson Corporation...
Page 69
NOTE A: Refer to the Kits section to order this part. B: These parts are included with 13A but can be ordered separately. C: The pressure transducer is application specific: 1000 psi: Order 1084753 3000 psi: Order 1084752 AR: As Required NS: Not Shown Part 1606702-05 E 2020 Nordson Corporation...
See Figures 39, 40, 41, and the parts list that begins on page 68. PART OF 13 THESE PARTS ARE APPLICATION SPECIFIC. THESE PARTS ARE INCLUDED WITH GUN OR MANIFOLD. Figure 39 S165 120/240 V Heated E-Net Dispenser Parts Part 1606702-05 E 2020 Nordson Corporation...
Page 71
Pro-Meter S-Series Coupled Dispensers with Integrated Drive GND TERMINAL FROM CORDSET Figure 40 S165 120/240 V Heated E-Net Dispenser Parts (Continued) Part 1606702-05 E 2020 Nordson Corporation...
Page 72
− − − − − − − − S WASHER, lock, M, internal, M3, per ISO 7079 − − − − − − − − S SCREW, socket, M3 x 6, black, per ISO 4762 Continued... Part 1606702-05 E 2020 Nordson Corporation...
Page 73
D: See Figure 41 for ferrule location. AR: As Required NS: Not Shown 120 VOLT CIRCUIT 240 VOLT CIRCUIT HEATER CATRIDGE HEATER CATRIDGE HEATER CATRIDGE HEATER CATRIDGE CORDSET CORDSET Figure 41 S165 120/240 Volt Heated E-Net Dispenser Parts (Continued) Part 1606702-05 E 2020 Nordson Corporation...
Pro-Meter S-Series Coupled Dispensers with Integrated Drive S300 Temperature Conditioned E-Net Dispenser See Figure 42 and the following parts list. Figure 42 S300 Temperature Conditioned E-Net Dispenser Parts Part 1606702-05 E 2020 Nordson Corporation...
Page 75
S ADHESIVE, Loctite, red 271, high strength, 50 ml NOTE A: Refer to the Kits section to order this part. B: These parts are included with 21A but can be ordered separately. AR: As Required NS: Not Shown Part 1606702-05 E 2020 Nordson Corporation...