Advertisement
A) Make sure that you use 2 different channel numbers that are at least 10 numbers
apart. This will prevent possible crosstalk between the 2 channels being used. For ex-
ample: If you use channel number 10 for one transmitter, use channel number 20 for the
other transmitter. The 2 channels on the receiver must also be set on the numbers 10
and 20.
B) The system will operate properly if both transmitters are in close proximity to each
other, however make sure that both transmitters are at least 10 feet away from the re-
ceiver, this will prevent the frequencies from overlapping.
(6) PHONE jack:
Plug a stereo headphone into this jack to monitor sound - Ch. 1 will be heard on the left,
Ch. 2 on the right.
(7) DC 6 Volt Input: An optional charger/power supply and rechargeable batteries are
available for the 320UPR. For additional information or to order these products please
visit the Azden website at
www.azdencorp.com
NOTE: Using a power supply of the wrong voltage/current may damage the unit
and void the warranty.
(8) Shoe Stand:
Attach the 320UPR to the shoe-mount of the video camera by sliding it into place. Turn
the thumbwheel clockwise to tighten. Reverse this procedure to remove the 320UPR
from the camera.
(9) Antennas: For best reception the antennas should be pointed in an upward fashion.
Use caution, and do not force them into this position.
BODYPACK TRANSMITTER (30BT)
(10) Remove the battery compartment lid by sliding it down.
(11) Insert two fresh "AA" batteries* into the compartment. Make sure the battery polarity
is correct as marked inside the battery compartment.
In addition to the battery, inside the battery compartment you will find:
(12) MIC Input LEVEL Control
This control enables you to adjust the input level of the microphone. Using the supplied
tool, turn the dial clockwise to increase, or counterclockwise to decrease the input level.
(13) POWER
Switches the transmitter "ON" or "OFF".
2
or contact your Azden dealer.
(14) MIC Input Jack
Plug the supplied EX-503L microphone into the MIC input jack and tighten the collar until
snug (DO NOT OVERTIGHTEN). In addition to the EX-503L, other lapel and/or headset
microphones with 3.5mm mini plugs can also be used with the 30BT.
(15) LCD Display
This display shows the following information.
Channel Number: 001 to 240
Battery Condition: Using a 3 step indicator - 1 (Low) to 3 (High)
To change the channel number: Use the tip of the tool provided and press the UP or
DOWN button to the desired channel, number appears (001 to 240). Once the desired
channel number has been selected on the transmitter, set the receiver to the same
channel number.
*While Alkaline batteries are preferred, you can use rechargeable Ni-Cd or Ni-MH batteries.
XLR PLUG-IN TRANSMITTER (30XT)
(16) Open the battery compartment lid by sliding it down and lifting it up.
Insert a 9 volt Alkaline battery into the compartment. Make sure the battery po-
larity is correct as marked inside the battery compartment.
(17) POWER
Switches the transmitter "ON" or "OFF".
(18) AUDIO
Prior to first turning the 30XT "ON" it is best to set the AUDIO switch to "OFF". When
you are ready to begin transmitting, switch to "ON". The "OFF" position acts as a
"mute" that maintains the RF signal but turns off the audio.
(19) MIC Connector/Locking Ring
This 3-pin XLR connector is the microphone input. Any low impedance microphone
with a corresponding connector can be attached here.
Once the microphone is plugged into the 30XT the locking ring should be ro-
tated clockwise until snug. To remove the microphone, first rotate the locking
ring counterclockwise and then, while pressing the XLR release, pull the micro-
phone away from the 30XT.
(20) MIC Input LEVEL Control
The MIC input LEVEL control enables you to adjust the input level of the connected
microphone. Using the supplied tool, turn the dial clockwise to increase, or
counterclockwise to decrease the input level
3
Advertisement
