Advertisement
(21) LCD Display:
The display will light up when the power is turned "ON". The LCD display shows the
following information.
Channels number: 001 to 240
Battery Condition: Using a 3 step indicator – 1(Low) to 3 (High)
To change the channel number, use the tip of the tool provided and press the UP or DOWN
button until the desired channel number appears (001 to 240). Once the desired channel
number has been selected on the transmitter, set the receiver to the same channel number.
HANDHELD MICROPHONE/TRANSMITTER (30HT)
(22) Remove the battery compartment cover by rotating it counterclockwise and sliding it
down.
(23) Insert two fresh Alkaline "AA" batteries into the compartment. Make sure the battery
polarity is correct as marked inside the battery compartment.
In the battery compartment you will also find:
(24) MIC LEVEL Control
The MIC LEVEL control enables you to adjust the audio level of the microphone. Using the
supplied tool, turn the dial clockwise to increase, or counterclockwise to decrease the
microphone's audio level.
(25) UP/DOWN Channel Buttons
To change the channel number, use the tip of the tool provided and press the UP or DOWN
button until the desired channel number appears (001 to 240). Once the desired channel
number has been selected on the transmitter, set the receiver to the same channel number.
(26) POWER
Switches the transmitter "ON" or "OFF".
(27) LCD Display:
The display will light up when the power is turned "ON". The LCD display shows the
following information.
Channel number: 001 to 240.
Battery Condition: Using a 3 step indicator - 1 (Low) to 3 (High)
4
Thank you for purchasing Azden's 320 wireless microphone system. Depending on
which system you ordered this package will contain one or more of the following compo-
nents: the 320UPR receiver, the 30BT body-pack transmitter with EX-503L lavalier mi-
crophone, the 30XT XLR plug-in transmitter and/or the 30HT handheld microphone
transmitter. This equipment is designed primarily for video cameras but is usable with
most electronic components having a microphone level input. The 320UPR allows you to
"receive" audio from two different transmitters simultaneously.
RECEIVER (320UPR)
(1) Remove the battery compartment lid by sliding it down.
(2) Insert two fresh alkaline "AA" batteries into the compartment. Make sure the battery
polarity is correct as marked inside the battery compartment.
(3) POWER (one switch for each channel)
Switches the receiver CH1 and/or CH2 "ON" or "OFF".
(4) MIC OUT jack:
The 320UPR is supplied with both a mini-to-mini and a mini-to-dual XLR cable.
For mini jack microphone inputs: Use the supplied mini-to-mini cable. Plug one
end of the cable into the receiver and the other end of the cable into the micro-
phone input of the video camera.
For 3-pin XLR microphone inputs: Use the supplied mini-to-dual XLR cable. Plug
the mini-plug end of the cable into the receiver (use the screw-down sleeve to se-
cure it to the receiver) and plug the XLR ends of the cable into the microphone
inputs of the video camera. Ch.1 is on the "Tip" connector, Ch.2 is on the "Ring".
(5) LCD Display:
There are two displays, one for CH1 and one for CH2. The display for each channel will
light up when the power for that channel is turned "ON". The LCD displays show the
following identical information.
Channel Number: 001 to 240
Battery Condition: Using a 3-step indicator - 1 (Low) to 3 (High)
Reception Level: Using a 4-step indicator - 1 (Low) to 4 (High)
To change the channel number, use the tip of the tool provided and press the UP or
DOWN button until the desired channel number appears ( 001 to 240). Once the desired
channel number has been selected on the receiver, set the transmitter to the same
channel number.
NOTE: When using two transmitters with the 320UPR please do the following:
1
Advertisement
