Azden 305HT User Manual page 4

305 system

Hide thumbs

page of 4

/ 4
Bookmarks

Enlarged version

(6) PHONE jack:

Plug a headphone into this 3.5mm jack to monitor sound.

(7) Shoe-Mount:

Attach the 305UPR to the shoe-mount of the video camera by sliding it into place. Turn

the thumbwheel clockwise to tighten. Reverse this procedure to remove.

(8) Antenna: For best reception the antenna should be pointed in an upward fashion.

Use caution, and do not force it into this position.

(9) Phone Output Adjustment: Using the supplied tool, turn the screw clockwise to in-

crease earphone level and counterclockwise to decrease.

BODYPACK TRANSMITTER (35BT)

(10) Remove the battery compartment lid by sliding it down.

(11) Insert two fresh "AA" Alkaline* batteries into the compartment. Make sure the bat-

tery polarity is correct as marked inside the battery compartment.

In addition to the battery, inside the battery compartment you will find:

(12) MIC Input LEVEL Control:

This control enables you to adjust the input level of the microphone. Using the supplied

tool, turn the dial clockwise to increase, or counterclockwise to decrease the input level.

(13) POWER:

Switches the transmitter "ON" or "OFF".

(14) MIC Input Jack

Plug the supplied EX-503L microphone into the MIC input jack and tighten the collar until

snug (DO NOT OVERTIGHTEN). In addition to the EX-503L, other lapel and/or headset

microphones with 3.5mm mini plugs can also be used with the 35BT.

(15) LCD Display:

This display shows the following information:

TV:Transmit Channel Number: 30:01 – 33:47

Battery Condition: Using a 3 step indicator - 1 (Low) to 3 (High)

To change the TV:Transmit channel number: Use the tip of the tool provided and press

the UP or DOWN button to the desired channel, number appears (refer to the included

chart). Once the desired TV:Transmit channel number has been selected on the trans-

mitter, set the receiver to the same number.

The TV:Transmit channel display is made of two parts. The first number is the actual TV

channel (30-33) and the second is the "transmit channel" number (01-47).

*While Alkaline batteries are preferred, you can use rechargeable Ni-Cd or Ni-MH batteries.

(16) AUDIO:

Prior to first turning the 35BT "ON" it is best to set the AUDIO switch to "OFF". When

you are ready to begin transmitting, switch to "ON". The "OFF" position acts as a

"mute" that maintains the RF signal but turns off the audio.

XLR PLUG-IN TRANSMITTER (35XT)

(17) Open the battery compartment lid and insert two fresh "AA" Alkaline* batteries.

Make sure the battery polarity is correct as marked inside the battery compartment

*While Alkaline batteries are preferred, you can use rechargeable Ni-Cd or Ni-MH batteries.

(18) POWER:

Switches the transmitter "ON" or "OFF".

(19) AUDIO:

Prior to first turning the 35XT "ON" it is best to set the AUDIO switch to "OFF". When

you are ready to begin transmitting, switch to "ON". The "OFF" position acts as a

"mute" that maintains the RF signal but turns off the audio.

(20) MIC Connector/Locking Ring:

This 3-pin XLR connector is the microphone input. Any low impedance microphone

with a corresponding connector can be attached here.

Once the microphone is plugged into the 35XT the locking ring should be ro-

tated clockwise until snug. To remove the microphone, first rotate the locking

ring counterclockwise and then, while pressing the XLR release, pull the micro-

phone away from the 35XT.

(21) MIC Input LEVEL Control:

The MIC input LEVEL control enables you to adjust the input level of the connected

microphone. Using the supplied tool, turn the dial clockwise to increase, or counter-

clockwise to decrease the input level.

(22) LCD Display: