Table of Contents
Advertisement
SPECIFICATIONS
1000URX - 1000URX\AB - 1000URX\Si - 1000URX\VM
RF Carrier Frequency Range
Effective Operating Range
Frequency Response
RF Sensitivity (12dB SINAD)
Adjacent Channel Selectivity
Image Rejection
IF Rejection
Audio THD
Audio Output
+4dBm ± 40kHz Deviation (-40dBm ± 5kHz Deviation for 1000URX\Si)
Output Impedance
Signal/Noise Ratio
Power Requirements
11 - 15V DC @ 220mA (10 - 17V DC @ 200mA for 1000URX\Si)
Dimensions (1000URX)
Operating Temperature Range
Weight
1000BT
Output Power
Max Modulation Sensitivity
MIC Level / Imped.
Power Requirements
Dimensions
Weight w/Battery
1000XT
Output Power
Max Modulation Sensitivity (ECM -- Dynamic)
MIC Level / Imped. (ECM)
MIC Level / Imped. (Dynamic)
Power Requirements
Dimensions
Weight w/Battery
Due to constant improvements, specifications are subject to change without notice.
Licensing
Licensing of this, or any Azden wireless equipment is the user's responsibility. The ability to receive a license
depends largely on the user's classification, application and frequency. Contact the appropriate agency (FCC in
the USA) for further information.
Azden Corporation, 147 New Hyde Park Road, P.O. Box 10, Franklin Square, NY 11010
vox - 516.328.7500 • fax - 516.328.7506 • email - azdenus@azdencorp.com
© 2003-2005 Azden Corporation
121 steps ~ 723.000 - 735.000MHz
MicroComputer Controlled PLL Synth.
200 - 300 ft ~ 60 - 100m
50 - 15kHz (± 1.5dB)
> 73dB (± 250kHz)
Line - 600Ω Ω Ω Ω Ω ~ MIC - 600Ω (
Ω (
Ω (
Ω (
Ω (300Ω Ω Ω Ω Ω for 1000URX\Si)
> 62dB (± 5kHz Deviation)
3.3 (W) x 3.9 (H) x 1.2 (D) inches
84 (W) x 100 (H) x 30 (D) mm
32
- 113
F ~ 0
0
0
9.88 ounces ~ 280g for 1000URX
15.87ounces ~ 450g for 1000URX\AB
8.81ounces ~ 250g for 1000URX\AB
-60dBm / 2.2kΩ Ω Ω Ω Ω (± 5kHz Deviation)
9V DC (Alkaline) @ < 62mA
2.5 (W) x 3.85 (H) x 1.0 (D) inches
63 (W) x 98 (H) x 27 (D) mm
5.64 ounces ~ 160g
+20dBM ~ 0dBm
-35dBm / 2.2kΩ Ω Ω Ω Ω (± 5kHz Dev.)
-55dBm / 2.2kΩ Ω Ω Ω Ω (± 5kHz Dev.)
9V DC (Alkaline) @ < 60mA
1.57 (W) x 4.4 (H) x 1.57 (D) inches
40 (W) x 112 (H) x 40 (D) mm
6.7 ounces ~ 190g
Printed in USA
User's Guide
1.2μ μ μ μ μ V
> 93dB
> 93dB
< 0.8%
1000URX • 1000URX\AB • 1000URX\VM • 1000URX\Si
- 45
C
0
0
20mW
-4dBm
20mW
P1020-05
1000BT • 1000XT
ENHANCED BROADCAST PERFORMANCE
UHF WIRELESS SYSTEM
Advertisement
Table of Contents
Related Manuals for Azden 1000BT
Summary of Contents for Azden 1000BT
-
Page 1: Specifications
Due to constant improvements, specifications are subject to change without notice. Licensing Licensing of this, or any Azden wireless equipment is the user’s responsibility. The ability to receive a license depends largely on the user’s classification, application and frequency. Contact the appropriate agency (FCC in the USA) for further information. - Page 2 (from 1 to 3 segments) with 3 segments meaning maximum battery power. The bottom segment will blink when the battery power falls to less than 6.2V and indicates that it is time to replace the battery. Azden recommends the use of Alkaline batteries only.
-
Page 3: Introduction
XLR release, pull the microphone away from the 1000XT. Thank you for selecting the Azden 1000 Series for your portable/ENG on-camera UHF wireless needs. We are confident that these compo- nents will perform beyond your expectations. -
Page 4: Table Of Contents
THE 1000URX\AB ...4 THE 1000URX\Si ... 4 THE 1000BT TRANSMITTER ... 5 Powering the 1000BT Transmitter ... 5 SETTING THE TRANSMITTING FREQUENCY ON THE 1000BT ... 6 USING THE 1000BT TRANSMITTER’S CONTROLS AND DISPLAY ... 6 Power ... 6 Audio ... 6 MIC ... -
Page 5: Receiver (1000Urx) Setup
(from 1 to 3 segments) with 3 segments meaning maximum battery power. The bottom segment will blink when the battery power falls to less than 6.2V and indicates that it is time to replace the battery. Azden recommends the use of Alkaline batteries only. -
Page 6: Attaching The Antennas To The 1000Urx
C. MIC This 4-pin Hirose connector [ ] is the microphone input. Azden pro- duces a number of lapel, head-worn and neck-worn microphones that are specifically suited for the 1000BT. In addition, other externally pow-... -
Page 7: Using The 1000Urx Receiver's Controls And Display
‘Channel’. To do this, after installing a fresh battery, turn the 1000BT to the ON position [ ]. Next, using the tip of a ballpoint pen, an unbent paper clip or something similar, press the MODE button [ ] repeatedly until one of the two screens below appears. -
Page 8: The 1000Urx\Ab
THE 1000BT TRANSMITTER Powering the 1000BT Transmitter The 1000BT uses a single Alkaline 9V battery for power. The battery is placed in the battery compartment by sliding the battery compartment door [ ] down and placing the battery in the compartment as shown in the illustration [♠].