Philips V60 User Manual page 206

Index
Check Vent: Internal Temperature High Mtr alarm 9-14
Check Vent: Machine Pressure Sensor Auto-Zero Failed
alarm 9-14
Check Vent: Machine Pressure Sensor Calibration Data Error
alarm 9-15
Check Vent: Machine Pressure Sensor Range Error alarm 9-
15
Check Vent: Motor Control PCBA ADC Failed alarm 9-15
Check Vent: O Flow Sensor Calibration Data Error alarm 9-
2
15
Check Vent: O Pressure Sensor Calibration Data Error alarm
2
9-15
Check Vent: O Supply Pressure Sensor Range Error alarm
2
9-15
Check Vent: OVP Circuit Failed alarm 9-15
Check Vent: Oxygen Device Failed alarm 9-15
Check Vent: Primary Alarm Failed alarm 9-15
Check Vent: Program CRC Test Failed alarm 9-15
Check Vent: Proximal Pressure Sensor Auto-Zero Failed
alarm 9-15
Check Vent: Proximal Pressure Sensor Calibration Data Error
alarm 9-15
Check Vent: Proximal Pressure Sensor Range Error alarm 7-
7, 9-16
Circuit, patient. See Patient circuit
Cleaning
ventilator exterior 10-2
CO rebreathing precautions 1-2, 1-4, 1-7, 1-8, 3-2
2
Communications interface B-1–B-6
using the ventilator with Philips monitors and VueLink
Open Interface B-3–B-5
Connector
oxygen inlet
how to install A-7
location 3-9
remote alarm/nurse call, location 3-9
RS-232 serial and analog I/O, location 3-9
Continuous positive airway pressure. See CPAP
Continuous-tone alarm 3-10
Contraindications 3-2
Control settings
how to change 6-3, 6-4, 6-19
how to make batch setting changes 6-19
list of descriptions and ranges 6-23–6-26
ranges, resolutions, and accuracies 11-1–11-2
See also name of specific setting
Cooling fan filter. See Filter, cooling fan
CPAP (continuous positive airway pressure) mode 4-8
CPAP (continuous positive airway pressure) setting, defini-
tion 6-23
D
Date and time, how to change E-6
Default factory settings, how to restore E-8
Definitions F-1–F-6
Delivered pressure specifications 11-10
Diagnostic mode E-1–E-15
how to calibrate touchscreen E-14–E-15
how to change baud rate E-10
how to change date and time E-6
Index-2
how to change language E-4–E-5
how to change pressure unit E-7
how to enable or disable Alarm Volume Escalation E-11
how to enable software options E-9
how to enter E-1
how to exit E-15
how to restore default factory settings E-8
how to view event log E-12–E-13
Dimensions, ventilator 11-6
Disinfecting
ventilator exterior 10-3
Display, brightness, how to set 6-17
Disposal 10-8
E
E-cycle (expiratory cycle Sensitivity) setting, definition 6-23
Elastance, definition 4-13
Electrical specifications 11-7, 11-8
Electromagnetic compatibility (EMC), compliance with stan-
dards D-1
Environmental specifications 11-6
EPAP (expiratory positive airway pressure) setting, definition
6-23
Estimated exhaled tidal volume. See V
Estimated minute ventilation. See V
Estimated total leak. See Tot.Leak
Event log, how to view E-12–E-13
Exhalation port
how to select 6-12–6-15
part numbers C-2
Exhalation port test, how to run 6-16–6-17
Exhale breath phase indicator, definition 8-2
Expiratory positive airway pressure. See EPAP
F
Fan filter. See Filter, cooling fan
Filter
air inlet
how to install 10-6
maintenance schedule 10-5
cooling fan
how to clean or replace 10-7
location 3-9
maintenance schedule 10-5
part number C-4
main flow (inspiratory) bacteria, part numbers C-4
First-time installation A-1–A-9
Fitting. See Connector
Flow assist/maximum resistance setting. See Max R
Frequency, breath. See Rate
G
General information 3-1–3-12
Glossary F-1–F-6
Graphical user interface
how to calibrate E-14
how to use 3-13
illustration 3-12
GUI. See Graphical user interface
T
E