Download Print this page
Gecko Y Series Startup Manual
Hide thumbs Also See for Y Series:

Advertisement

Start up guide
and basic configuration
Y series and in.xe
Display sequence at start-up
Breaker setting
Programming the control system
Quick start card chart
Programming options

Advertisement

loading
Need help?

Need help?

Do you have a question about the Y Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Gecko Y Series

  • Page 1 Start up guide and basic configuration Y series and in.xe Display sequence at start-up Breaker setting Programming the control system Quick start card chart Programming options...
  • Page 2: Table Of Contents

    Table of contents Warning �������������������������������������������������������������������������������������������������������������������������������������������������������������������������� 2 Power up and breaker setting ����������������������������������������������������������������������������������������������������������������������������������������� 3 Programming the control system - Programming the control system with in�stik ����������������������������������������������������������������������������������������������������� 5 - Programming the control system with the keypad ��������������������������������������������������������������������������������������������� 6 Field programming options for control systems - Definitions Table �������������������������������������������������������������������������������������������������������������������������������������������������...
  • Page 3: Warning

    ® ® in�yj™, in�keys™, in�touch™, in�k200™, in�k400™, in�k450™, in�k600™, K-19™, K-35™, K-8™, in�k1000™, in�k800™, in�k500™, in�k300™, in�flo™, in�put™, in�seal™, in�link™, in�t�cip™, in�stik™, heat�wav™, Y Series™, and their respective logos are Trademarks of Gecko Alliance Group�   All other product or company names that may be mentioned in this publication are tradenames, trademarks or registered trademarks of...
  • Page 4: Power Up And Breaker Setting

    Power up and breaker setting IMPORTANT Please read the following before starting the device. Verify that all accessories are linked to the ground lug and connected to the to the control system. A minimum flow of 68 LPM (18 GPM) is required. Make sure that all valves are open in the spa plumbing and that the water flow is sufficient between the main pump and the water heater.
  • Page 5 Power up and breaker setting in.yj Selecting number of phases Menu not available 1 or 2 It is important to specify Choose the number of The values displayed by the current rating of the phases supplying your the system correspond in.ye et in.yt spa (1 to 3)�...
  • Page 6: Programming The Control System

    Cut the power� Press on the Prog� key When starting up, If, at start up, the keypad For the Y series control the control system will to confirm the chosen displays a flashing “L xx”, systems remove the download the different configuration�...
  • Page 7: Programming The Control System With The Keypad

    Programming the control system with the keypad Although every control The keypad will display Press on the Prog� key system of the Y series L xx� “xx” corresponds to to confirm the chosen and in�xe are factory the number of the low-level configuration�...
  • Page 8: Field Programming Options For Control Systems

    Field programming options for control systems If none of the pre-programmed low-level configurations in the control system suits your spa model, it is possible to have a personalised system configuration by entering manually the setting parameters (see the corresponding table for your spa’s control system)�...
  • Page 9 Field programming options for control systems Table 1 (continued) – in.yj, in.ye, in.yt and in.xe Parameter Screen Options Description --,1H,1L,2H,2L,3H,3L,4H, 4L,P5,BL, Accessory connected to the relay of output 4 Output 4 CP,O3,L2,H,FN,ON,PR,H2,FA,AU *available for in.ye, in.yt and in.xe --,1H,1L,2H,2L,3H,3L,4H, 4L,P5,BL, Accessory connected to the relay of output 5 Output 5 CP,O3,L2,H,FN,ON,PR,H2,FA,AU *available for in.ye, in.yt and in.xe...
  • Page 10 Field programming options for control systems Table 1 (continued) – in.yj, in.ye, in.yt and in.xe Parameter Screen Options Description Current of accessory connected to output 4 Output 4 current 0 to 15 amps *available on in.ye, in.yt and in.xe Current of accessory connected to output 5 Output 5 current 0 to 15 amps *available on in.ye, in.yt and in.xe...
  • Page 11 Field programming options for control systems Table 2 – in.xe (older versions only) Parameter Screen Options Description --,1H,1L,2H,2L,3H,3L,4H, Output 1A Accessory connected to the relay of output 1A 4L,P5,BL,CP,O3,L2,H --,1H,1L,2H,2L,3H,3L,4H, Output 1B Accessory connected to the relay of output 1B 4L,P5,BL,CP,O3,L2,H --,1H,1L,2H,2L,3H,3L,4H, Output  2 Accessory connected to the relay of output 2A 4L,P5,BL,CP,O3,L2,H...
  • Page 12 Field programming options for control systems Table 3 - in.xe (older versions only) Parameter Screen Options Description Single speed = 1 Pump 1 configuration Pump 1 config� Double speed = 2 *Offered on certain models only� *Pump 1 and Pump 3 = 3 Not installed = 0 Pump 2 config�...
  • Page 13: Specifications

    Specifications For more information on the specifications concerning the outputs of a specific control system, refer to the corresponding techbook� in�yj-V3 techbook Y series techbook in�xe techbook...
  • Page 14 9919-101312-B Rev. 01-2019 Gecko Alliance 450 des Canetons, Quebec City (Qc), G2E 5W6 Canada, 1.800.78.GECKO © Groupe Gecko Alliance inc., 2019 All trademarks or registered trademarks www.geckoalliance.com are the property of their respective owners. Printed in Canada...

This manual is also suitable for:

In.xe series