Digital color + white transfer media printer (34 pages)
Summary of Contents for Uninet IColor 500
Page 1
Setting the Multipurpose tray to work with specific sized papers with the iColor® iColor® transfer papers come in a variety of sizes, so it is recommended that you set the MPT tray to the size of the paper that you most commonly use. If the MPT tray identifies a paper that is not within its set parameters, the iColor® 500 printer will prompt you to press the online button after each print. Adjusting the settings will avoid this for the specific size you set. The following instructions are for printers that have been set up within a network, using an IP address. Use your web browser to change the default settings: 1) From your web browser, go to 192.168.X.X (the specific IP address assigned to your printer) 2) Navigate to the admin menu and enter the username (root) and password (aaaaaa) (six lowercase letter a’s) 3) Change all settings to match the following for Printer > Print Setup > Print Method: ...
Page 2
4) Change all settings to match the following for Media Setup. The MPTray setting is the most important setting. The Media Type and Media Weight can be set to your most common settings, but the RIP will over ride: 2 UniNet 3232 W. El Segundo Blvd., Hawthorne, California 90250 | sales@icolorprint.com www.icolorprint.com ...
Page 3
5) With these settings in place, you will be able to print to the MPTray without pressing the online button at all (even for the first page out, it prints completely unattended). When using the printer without the iColor® TransferRIP, the printer will now always look for paper in the MPT first. If it does not find it there it will pull from the tray on bottom so this setting works great for all uses. 6) When using the iColor® TransferRIP, you should not check the ‘Force Manual Tray’ box and the input tray should be set to ‘Printer Default’. If you are not networking your printer, the following instructions are for printers that have been set up via direct connection using the USB port: 1) Press the ‘Menu’ button and scroll down to ‘Menus’ and press enter 3 UniNet 3232 W. El Segundo Blvd., Hawthorne, California 90250 | sales@icolorprint.com www.icolorprint.com ...
Page 4
2) Select ‘Tray Configuration’ and press enter 3) Select ’Paper Feed’ and press enter 4) Select ‘MPTray’ and press enter 4 UniNet 3232 W. El Segundo Blvd., Hawthorne, California 90250 | sales@icolorprint.com www.icolorprint.com ...
Page 5
5) Press back, select ‘Auto Tray Switch’ and press enter 6) Select ‘On’ and press enter 7) Press back, select ‘Tray Sequence’, select ‘Down’ and press enter 5 UniNet 3232 W. El Segundo Blvd., Hawthorne, California 90250 | sales@icolorprint.com www.icolorprint.com ...
Page 6
8) Press back, select ‘MPTray Config’ and press enter 9) Select ‘Paper Size’, press enter. Select ‘Letter’ and press enter 10) Press back, select ‘Media Type’, press enter. Select ‘Glossy’ and press enter 6 UniNet 3232 W. El Segundo Blvd., Hawthorne, California 90250 | sales@icolorprint.com www.icolorprint.com ...
Page 7
11) Press back, select ‘Media Weight’, press enter. Select ‘Heavy’ and press enter 12) Press back, select ‘Tray Usage’, press enter. Select ‘When Mismatching’ and press enter 13) Press the online button to return to the main screen. You are now ready to print on your preferred media through the MPTray without pressing online! 7 UniNet 3232 W. El Segundo Blvd., Hawthorne, California 90250 | sales@icolorprint.com www.icolorprint.com ...