Advertisement
Page 6
SB-2-510-B
TROUBLESHOOTING (continued)
CONDITION
Fluid dripping or leaking from
bottom of cup
Runs and sags
Thin, sandy coarse finish drying
before it flows out
Thick, dimpled finish "orange peel"
ACCESSORIES
SRI-5033-205 Air Cap Test Kit
The purpose of this test kit is
to measure air cap pressures.
Used to confirm code com-
pliance and as a daily quality
control measure.
Automotive Refinish Quick Connects
For HVLP Guns (Air)
High Flow Type.
HC-4419 Stem
HC-4719 Coupler
1/4" NPT(F)
1/4" NPT(M) /NPS(M)
HC-1166 Stem
HC-4720 Coupler
1/4" NPT(M)
1/4" NPT(F)
192219 Gun Holder, Coated
WORLDWIDE SALES AND SERVICE LISTING - DeVILBISS AUTOMOTIVE REFINISHING - DeVilbiss has authorized distributors throughout the world. For
equipment, parts and service, check the Yellow Pages under "Automobile Body Shop Equipment and Supplies". If further assistance is required, write or call
one of the following DeVilbiss Distribution Centers or Sales Offices nearest you. FOR TECHNICAL ASSISTANCE, CALL TOLL FREE 1-800-445-3988 (U.S. AND
CANADA ONLY).
CAUSE
Cup loose on gun.
Cup gasket worn or missing below cup.
Cup threads dirty.
Too much material flow.
Material too thin.
Gun tilted on an angle, or gun
motion too slow.
Gun too far from surface.
Too much air pressure.
Improper thinner being used.
Gun too close to surface.
Air pressure too low.
Improper thinner being used.
Material not properly mixed.
Surface rough, oily, dirty.
MSP-524
Twin Cartridge, Paint Spray
NIOSH-Certified (TC84A-1623)
for respiratory protection in
atmospheres not immediately
dangerous to life.
HAV-500 OR
HAV-501
Adjusting Valve
(HAV-501 SHOWN)
HAV-500 does not
have pressure gauge.
Use to control air
usage at gun.
192212 Professional
Spray Gun Cleaning Kit
Contains six precision tools
designed to efffectively clean
all DeVilbiss, Binks, Finishline
and other brand products.
10/02
©Copyright 2002, DeVilbiss
CORRECTION
Tighten.
Replace cup gasket.
Clean.
Adjust gun or reduce fluid flow.
Mix properly or apply light coats.
Hold gun at right angle to work and
adapt to proper gun technique.
Check distance. Normally approx. 3-6".
Reduce air pressure and check spray pattern.
Follow paint manufacturer's mixing instrs.
Check distance. Normally approx. 3-6".
Too much material coarsely atomized.
Increase air pressure or reduce fluid flow.
Follow paint manufacturer's mixing instrs.
Properly clean and prepare.
KK-5060 Air Cap
54-4350 Gun Holder
Consists of: 2 brushes,
1 wire pick. Helps keep
Designed to hold gravity
feed guns and cups. Also
air cap clean and per-
holds paint strainers.
forming properly.
81-381 8 oz. Gravity Feed
Cup Assembly
192218 Scrubs
Hand Cleaner Towels
Scrubs® are a premoistened
hand cleaner towel for painters,
body men and mechanics that
go where you go and no water
is needed.
www.devilbiss.com
HAF-507
Cleaning Kit
Whirlwind™
In-Line Air Filter
Removes water, oil,
and debris from the
air line.
Spray Gun Lube
SSL-10 (2 oz. bottle)
Compatible with all paint materials;
contains no silicone or petroleum
distillates to contaminate paint.
MSDS Sheet available upon request.
®
Printed in U.S.A.
Advertisement
