Related Manuals for Team Corally KRONOS XTR 6S
Summary of Contents for Team Corally KRONOS XTR 6S
- Page 1 Download the latest version of this manual from www.corally.com. Revised : 2021-03-25 www.corally.com C-00173_manual...
- Page 2 INTRODUCTION Thank you for purchasing a Team Corally car. This manual describes the instructions for using the model and the elec- tronic components. You will also find some tips on how to maintain your RC model so that you can enjoy it for years to come.
- Page 3 Take all necessary precautions before, during and after using your model. You are responsible for the safe as- sembly, maintenance and use of your model. In case of any questions, contact your local reseller or contact Team Corally support for assistance. SAFETY PRECAUTIONS ( All models ) For your safety, always use wear gloves and goggles when assembling and maintaining your model.
- Page 4 He must send the defective goods to our local rep- resentatives or directly to Team Corally / JSP Group Intl bvba, Geelseweg 80, 2250 Olen, Belgium at his own risk and cost.
- Page 5 LIPO BATTERY SAFETY PRECAUTIONS ( All models ) • Follow and respect the manufacturer’s instructions for use • It is important to check that your ESC is set to LIPO if you are using a LIPO battery. Failure to comply with this instruc- tion will result in increased battery discharge and may cause fire and damage to persons and property.
-
Page 6: Car Components
CAR COMPONENTS Front Differential Front Shock Absorber Anti-Roll Bar Suspension Arm Steering Block Steering Link Steering Servo Battery compartment Not Included Battery not Included Receiver Box Centre Differential Not Included Brushless Motor Controller (ESC) Power Switch Not Included Not Included Rear Suspension Arm Turnbuckle Rear Shock Absorber... - Page 7 QUICK START GUIDE ( General for all models) READ THE INSTRUCTIONS CHARGE THE BATTERY INSTALL 4x AA BATTERY CHARGER BATTERY MAKE SURE THAT ALL SCREWS AND NUTS ARE INSTALL THE BATTERY TURN ON THE TRANSMITTER (Always First) TIGHTENED PROPERLY. CONNECT THE BATTERY TO THE ESC CHECK THE FUNCTIONS CHECK THE RADIO SYSTEM RANGE SWITCH ON THE ESC...
- Page 8 BASIC CAR SETTINGS FRONT TOE TOE-OUT TOE-OUT -1° -1° 72mm Adjust the angle by screwing the TURNBUCKLE. FRONT CAMBER REAR CAMBER -1° -1° -2° -2° 63mm 63mm Adjust the angle by screwing the TURNBUCKLE. Adjust the angle by screwing the PIVOT BALL. FRONT CASTER 28°...
-
Page 9: Ride Height
BASIC CAR SETTINGS SUSPENSION TRAVEL It is important to properly adjust the travel of the suspension arm to prevent the shock absorber from reaching the end of its travel and damaging it. • Place the chassis on a block in order to release the suspension to the maximum. •... -
Page 10: Install Electronics
INSTALL ELECTRONICS SERVO INSTALLATION 17mm Recommended Servo : Digital Servo - CS-5226 - High Voltage #C-52001 ESC INSTALLATION Recommended ESC : Speed Controller - TOROX 185 - Brushless - 2-6S #C-54011... -
Page 11: Motor Installation
INSTALL ELECTRONICS MOTOR INSTALLATION IMPORTANT : To adjust the space between the pinion and the spur gear, refer to “Gear Mesh Connect the motor to the controller as described in Adjustment” section. the controller manual. Apply some Corally Screw Fix - Blue # C-13094 RECEIVER INSTALLATION Connect the servo cable to channel 1 of the receiver. -
Page 12: Battery Installation
INSTALL ELECTRONICS BATTERY INSTALLATION Recommended Battery : LiPo battery 4S - 6S - Install the battery. - Connect the battery to the ESC. - Secure the battery with the Battery Straps... -
Page 13: Gear Ratio
GEAR RATIO MOTOR PINION MOD1.0 High-performance 13T tooth pinion gear, manufactured from special steel for toughness and durability with precise tolerances and assures unparalleled concentricity. Created on a special gear machine, all pinions feature ultra-precise tooth shaping and ultra-true running for vibration-free operation. - Page 14 SHOCK ABSORBER MAINTENANCE It may be necessary to replace the silicone oil in the shock absorbers every 40 runs. It depends on how you drive and the type of terrain you drive on. Remove the shock absorbers from the car. (4x) Remove the shock cap.
- Page 15 SHOCK ABSORBER - EXPLODED VIEW Do not overtighten the Shock Cap to C-00180-080 Shock Piston prevent deformation of the silicone Shock Bladder. C-00180-133 Set content C-00180-189 Shock Piston - 4x1.6 Shock Piston - 4x1.8 C-31001-25 Shock Piston - 5x1.4 C-00180-080 Shock Piston - 5x1.5 Shock Piston - 5x1.6 C-00180-190...
- Page 16 REMOVING THE CENTRE DIFFERENTIAL It may be necessary to replace the silicone oil every 50 runs. It depends on how you drive and the type of terrain you drive on. - Remove 4 screws. - Release the Centre Diff Plate Cover. - Extract the differential and follow the maintenance instruction on the DIFFERENTIAL MAINTENANCE section.
-
Page 17: Differential Maintenance
DIFFERENTIAL MAINTENANCE It may be necessary to replace the silicone oil every 50 runs. It depends on how you drive and the type of terrain you drive on. • 1. Remove 2 screws under the chassis. • 2. Remove the 2 fixing screws from the differential cover. - Page 18 FRONT & REAR DIFFERENTIAL - EXPLODED VIEW C-3002-30-12 (x4) C-00180-153-3 C-00180-205 C-3611-3-08-16-05 C-00180-179 (set) C-00180-182 C-00180-184 C-00180-178 C-00180-205 C-00180-183 C-00180-182 C-3611-3-08-16-05 C-00180-153-3 C-00180-098 CENTRE DIFFERENTIAL - EXPLODED VIEW C-3002-30-10 (x4) C-00180-154-3 C-00180-205 C-3611-3-08-16-05 C-00180-179 (set) C-00180-205 C-00180-684 C-00180-182 C-00180-607 C-00180-183-1 C-00180-686 C-00180-182 C-3611-3-08-16-05...
- Page 19 FRONT DRIVE TRAIN - EXPLODED VIEW C-00180-117 C-00180-329 C-3004-40-04 C-00180-122 C-00180-108 (2x) C-00180-123 (2x) C-3101-30 (x2) C-00180-108 C-3003-30-10 (2x) C-3003-30-10 C-3611-3-08-16-05 (2x) C-00180-207 C-00180-150 C-3201-60 (2x) C-00180-039 C-00180-144-2 C-00180-101-2 C-00180-040 C-00180-150 C-00180-193 C-3003-30-16 C-00180-341 C-00180-149 C-00180-089 C-00180-100-2 C-3003-30-20 C-00180-051 M4x10 C-00180-419 C-31205 (x5) C-00180-055 (2x)
- Page 20 REAR DRIVE TRAIN - EXPLODED VIEW C-00180-005-2 C-3003-30-10 (x2) C-00180-226-B C-3001-30-20 C-3002-30-12 (x2) C-00180-535 C-3101-40 (x2) C-00180-005-2 C-3101-30 (x4) C-3101-30 C-3003-30-12 (x2) C-00180-005-2 C-00180-030 C-31205 (x5) C-3003-30-25 C-00180-122 DIN916•M4x4 C-00180-539 C-3003-30-10 (x2) C-00180-055 C-3003-30-18 (x6) C-00180-148 C-00180-329 C-00180-041 C-00180-676 C-3101-30 C-00180-114 C-00180-293 C-00180-030...
-
Page 21: Chassis - Exploded View
CHASSIS - EXPLODED VIEW C-00180-301 (set) C-3002-30-08 (x2) not included C-3001-40-12 Nylstop Nut•M3 C-00180-023 C-3002-30-14 (x2) C-00180-305 C-3001-40-10 (x2) C-00180-301 (set) Nylstop Nut•M3 M4x4 C-3001-40-10 C-3003-30-10 (x2) C-00180-305 C-3002-30-08 C-00180-177 C-3003-30-12 (x4) C-00180-605 C-3003-30-35 C-00180-171 C-72113 C-3003-30-10 C-3002-40-10 (x2) C-3003-30-18 C-3002-30-06 C-00180-129 C-00180-604... -
Page 22: Spare Parts
SPARE PARTS C-00180-005-2 C-00180-013 C-00180-018 C-00180-004-1 Wing Mount - Adjustable - Servo Mount - Receiver Box - Center Diff Bulkhead - Compos- Battery Strap - Hook & Loop Composite - 1 Set Composite - 1 Set ite - 1 Set - 2 pcs C-00180-020 C-00180-021... - Page 23 SPARE PARTS C-00180-122 C-00180-123 C-00180-127 C-00180-129 C-00180-133 Pin 2.5x17mm - Steel - 10 pcs Pivot Ball - Steel - 4 pcs Hinge Pin - Outer - Steel - 2 pcs Turnbuckle - M3 - 35mm - Shock Cap - Aluminium - Hard Steel - 2 pcs Anodised - 2 pcs C-00180-134...
- Page 24 SPARE PARTS C-00180-190 C-00180-191 C-00180-192 C-00180-193 C-00180-197 Shock Washer - 2.5x6x0.5mm - O-Ring - Silicone - 9x12mm O-Ring - Silicone - Drive Shaft - Center - Front - Anti-Roll Bar - 2.4mm - Front Steel - 10 pcs - 5 pcs 16.2x19.8mm - 5 pcs Steel - 1 pc - 1 pc...
- Page 25 SPARE PARTS C-00180-562 C-00180-604 C-00180-605 C-00180-686 C-00180-607 Centre Diff Support Spacer - Centre Diff Plate - Spur Gear Motor Bulkhead - Aluminium Diff Case - Centre - Aluminium. Spur Gear 52T - CNC Machined 4mm - Composite - 1 pc Cover - Composite - 1 pc - 1 pc - Steel - 1 pc...
-
Page 26: Option Parts
OPTION PARTS Graphite 3mm Graphite 3mm Graphite 3mm Graphite 3mm Fits part C-00180-104 C-00180-232 C-00180-233 C-00180-234 C-00180-235 C-00180-255 Suspension arm stiffener - A - Suspension arm stiffener - A - Suspension arm stiffener - B - Suspension arm stiffener - B - Chassis Brace Stiffener - Front Lower Front - Right - 1 pc Lower Front - Left - 1 pc... - Page 27 STEEL SCREWS LENGTH LENGTH LENGTH LENGTH HEX FLAT HEAD SCREWS HEX BUTTON HEAD SCREWS HEX SOCKET HEAD SCREWS HEX SET SCREWS DIN 7991 - STEEL - 10 PCS DIN 7380 - STEEL - 10 PCS DIN 912 - STEEL - 10 PCS DIN 916 - STEEL - 10 PCS NOMINAL LENGTH...
-
Page 28: Ball Bearings
NUTS NYLSTOP NUT NYLSTOP NUT - FLANGED NYLSTOP NUT LOW PROFILE NUT ALUMINIUM - 10 PCS ALUMINIUM - 10 PCS STEEL - 10 PCS DIN 936 - STEEL - 10 PCS NOMINAL NOMINAL NOMINAL NOMINAL COLOR COLOR COLOR COLOR SIZE SIZE SIZE SIZE... - Page 29 ALUMINIUM WASHERS WASHER FOR SOCKET HEAD SCREW WASHER FOR BUTTON HEAD SCREW WASHER FOR FLAT HEAD SCREW ALUMINIUM - 10 PCS ALUMINIUM - 10 PCS ALUMINIUM - 10 PCS FOR S/H FOR B/H FOR F/H COLOR COLOR COLOR SCREW SCREW SCREW Gold C-3214-20-0...
- Page 30 NOTE...
- Page 31 NOTE...
- Page 32 WWW.CORALLY.COM Team Corally is a registered trademark licensed to JSP Group Intl bvba Geelseweg 80 B-2250 OLEN Belgium • • • Tel: +32 14 25 92 94 info@corally.com • C-00173-M-EN...