Maintenance Manual – 8242 DECT Handset Table of contents About This Document ................................ 3 Audience ................................... 3 Important note: ................................3 Abbreviations ................................... 3 Document History ................................3 Handset - Service Menu Management ..........................4 Service Menu access ................................. 4 Service Menu Parameter Definitions ..........................
8242 DECT Handset 1 About This Document This document describes the features available through the Service Menu and the Test Menu in the 8242 Dect Handset. We describe how to operate the handset without going into details of its operations features.
Maintenance Manual – 8242 DECT Handset 2 Handset - Service Menu Management This section describes how to use the feature “Service Menu” available only to vendors or BPs or administrators of the handset. The document will also describe some options available in the Service Menu.
Maintenance Manual – 8242 DECT Handset 2.2.2 Reset settings This feature allows the Admin to clear only the changed parameters in Settings menu to default, without clearing the registration. Same function as the Reset Settings in the settings menu. Please note that it...
Page 6
Maintenance Manual – 8242 DECT Handset Or when Vol- key pressed: Line 4: RFPI in octal Line 5: RFPI in hex Lock State Freq Slot Base/DAP RPN Up to 5 bases/DAPs RSSI Up to 5 bases/DAPs Parameter/Line Description The line contains the list of base stations identified by the handset as RPNs of the bases in respect to the signal strength values below.
Page 7
Maintenance Manual – 8242 DECT Handset The Site survey can freeze the result, it can be hidden for the user and be unhidden. This is controlled via the side function key: 1. Press: Result is frozen and a “P” is shown to left upper corner 2.
Maintenance Manual – 8242 DECT Handset 2.2.4 HS Logs The HS log is a debugging feature that allows Admin to retrieve low level interesting messages from the handset. HS Logs Description Log error These are debug error logs retrieved from the PP log file. The last log retrieved is formatted into: Error: Log event error code.
Maintenance Manual – 8242 DECT Handset 2.2.5 Status This provides the present condition of the handset and the base station to which the handset is locked Some of the information available in this mode are described in the table below (this information is updated during location request update from the DECT system).
(Off) Narrowband codec are used, the option Prefer is not supported for the moment. Caution: Wideband for DECT handset is only supported by some equipment. Refer to system installation and configuration. Shall be left Off unless requested by Alcatel-Lucent staff. 8AL 90310 USAA Ed01 10 /18...
Maintenance Manual – 8242 DECT Handset 2.2.9 Test Tone on OK key When this feature is enabled (On) a 1 kHz test tone can be put into the audio streaming, e.g. when a call has been established press the OK key of the handset (where this feature is enabled) and the test tone is streamed through to the counterpart handset.
Maintenance Manual – 8242 DECT Handset 3 Handset – Test Menu Management This section describes how to use the feature “Test Menu” available only to vendors or BPs or administrators of the handset. Test Menu access This menu is useful for installers or support people to check that the hardware (Keypad, display, etc…) is working as expected.
Maintenance Manual – 8242 DECT Handset 3.2.2 Keyboard test Tests if all the keys are working as expected. Tester is requested to press all the keys on the HS for this test to pass. When the key is working as expected the red square will become green.
Maintenance Manual – 8242 DECT Handset 3.2.5 Battery test Tests if the Handset is inserted into the charger (cradle) or removed from the charger. 3.2.6 Audio test: The Audio test consists of several sub tests. In the following these will be described: 3.2.7 Earpiece tone test:...
Maintenance Manual – 8242 DECT Handset 3.2.9 Headset tone test: A 1000 Hz tone generated in the headset, a headset should be inserted into the HS at this point in time. 3.2.10 Headset Loopback test: The purpose is to test that audio path from headset’s microphone to headset’s earpiece is function. The tester blows or speaks in the headset’s microphone and verifies that he can hear it in the headset’s...
Maintenance Manual – 8242 DECT Handset 3.2.12 SD card test Intended to check presence of SD card and if yes, gives SD card Datas. Datas are manufacture number, card size etc... Caution: SD card features not available in R100 If no card is inserted, the following screen shot will ve shown: 3.2.13 Bluetooth...
Maintenance Manual – 8242 DECT Handset 3.2.15 DECT Mode Dect infos as seen in the screenshot 3.2.16 Prod Data This is the important production data of the handset: BB status: 0x01, RF status: 0x02 and Scan status :0x01 is the only valid values for a handset that has passed all production tests.
Note: There is no difference between Ex-factory default and master reset Legal notice: Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective owners. The information presented is subject to change without notice.