Delta DPA Series Instruction Sheet
Pressure sensor
Hide thumbs
Also See for DPA Series:
- Instruction sheet (9 pages) ,
- Instruction sheet (9 pages) ,
- Instruction sheet (2 pages)
Table of Contents
Advertisement
Quick Links
Call 1(800)985-6929 for Sales
Thank you very much for choosing Delta DPA series pressure sensor. Please read this instruction sheet carefully before using your DPA.
Keep this instruction sheet handy for quick reference.
Warning
DANGER! CAUTION! ELECTRIC SHOCK!
DPA is a pressure measurement device. DO NOT use it out of its specification. Improper pressure or incorrect wiring may
cause series injuries on staff or damages on other devices.
1. Keep away from high-voltage and high-frequency environment during the installation in case of interference. Prevent using the device in
premises which contain:
(a) dust or corrosive gas; (b) high humidity and high radiation; (c) shock and vibration.
2. DPA can only be used for air pressure measurement and should avoid corrosive, inflammable or toxic gas measurement.
3. Make sure the power supply is switched off when installing or dismounting DPA and the pressure source stops its action in case harms
occur on human body and properties.
4. DO use parts compatible to the specification of the pressure pore for connection to avoid mistaken measurement or safety problems.
5. Before switching on the power supply, check the signal connection, e.g. the input voltage and polarity. Voltage that is too high may cause
damages on DPA.
6. DO use dry cloth and DO NOT use acid or alkaline liquid to clean the device.
Product Profile & Outline
1. Analog output indicator
2. Digital output 1 indicator
3. Digital output 2 indicator
4. Pressure/parameter display
5. SV/setup item display
Contents in the pack: Pressure sensor, signal wire, unit sticker, instruction sheet
Optional accessories: Panel mounting parts, metal mounting parts
Call 1(800)985-6929 for Sales
deltaacdrives.com
Series Pressure Sensor
Instruction Sheet
6. UP key
7. SET key
8. DOWN key
9. Power supply and output terminals
10. Pressure input pore
- 1 -
deltaacdrives.com
sales@deltaacdrives.com
sales@deltaacdrives.com
Advertisement
Table of Contents
Related Manuals for Delta DPA Series
Summary of Contents for Delta DPA Series
- Page 1 Series Pressure Sensor Instruction Sheet Thank you very much for choosing Delta DPA series pressure sensor. Please read this instruction sheet carefully before using your DPA. Keep this instruction sheet handy for quick reference. Warning DANGER! CAUTION! ELECTRIC SHOCK! DPA is a pressure measurement device.
-
Page 2: Ordering Information
Call 1(800)985-6929 for Sales deltaacdrives.com sales@deltaacdrives.com Ordering Information Series name DPA: Delta DPA series pressure sensor 01: -100kPa ~ 100kPa 10: -100kPa ~ 1,000kPa Measurable pressure range N: NPN output + 4 ~ 20mA; P: PNP output + 4 ~ 20mA Output types M: NPN output + 1 ~ 5V;... - Page 3 Call 1(800)985-6929 for Sales deltaacdrives.com sales@deltaacdrives.com How to Set up Parameters Switching modes: DPA will be in the “Measuring Mode” when it is switched on, displaying PV and SV. Press for more than 2 seconds in this mode to switch to the “Quick Setup Mode”. Press for more than 4 seconds in the “measuring mode”...
- Page 4 Call 1(800)985-6929 for Sales deltaacdrives.com sales@deltaacdrives.com Measuring Mode: Quick Setup Mode Advanced Setup Mode Measuring Mode Set up auxiliary display Set up OUT1 mode Set up upper limit of OUT1 (Change SV display method) (Set OUT1 to hysteresis mode / window mode) Press ...
-
Page 5: Initial Setting
Call 1(800)985-6929 for Sales deltaacdrives.com sales@deltaacdrives.com Quick Setup Mode Advanced Setup Mode Measuring Mode Set up output response time Set up power saving mode Set up upper limit of OUT2 (Set OUT2 to hysteresis mode / window mode) Press ... -
Page 6: Analog Output
Call 1(800)985-6929 for Sales deltaacdrives.com sales@deltaacdrives.com In the “Measuring Mode”, press and find (OUT1 Hi), (OUT1 Lo), (OUT2 Hi) and (OUT2 Lo). Use to set up Hi/Lo values. [Figure 2: Output in Hysteresis Mode] 3. Window Mode: Set up pressure Hi/Lo. When the pressure measured is bigger than Hi or smaller than Lo, the output will be OFF. When the pressure measured is bigger than Lo and smaller than Hi, the output will be ON. -
Page 7: Copy Function
Call 1(800)985-6929 for Sales deltaacdrives.com sales@deltaacdrives.com Key Locking Function Lock On: Press together for 2 seconds until is displayed. You will then see the display of pressure value (PV) and set value (SV). Lock Off: Press together for 2 seconds until is displayed. - Page 8 Call 1(800)985-6929 for Sales deltaacdrives.com sales@deltaacdrives.com See the meanings of codes in the table below: digit digit digit digit OUT1 mode N.O./N.C. OUT2 mode N.O./N.C. Response time Color Referencing item for color OUT1 N.O. N.O. Easy Easy OUT2 N.C. N.C. Red when N.O.
-
Page 9: How To Install
4. Analog output signal (orange) 5. Negative power supply input (blue) The content of this instruction sheet may be revised without prior notice. Please consult our distributor or download the most updated version at http://www.delta.com.tw/industrialautomation. - 9 - Call 1(800)985-6929 for Sales deltaacdrives.com...