Table of Contents
Advertisement
By a specialized technician
To confi gure the hydraulic diagram, press the SET key and then
with the power key. PPress the SET key again to enter the menu and enter the access key in possession of only
with the power key. PPress the SET key again to enter the menu and enter the access key in possession of only
the technician authorized by the manufacturer. Confi rm the password using the set key and the key
the technician authorized by the manufacturer. Confi rm the password using the set key and the key
the technician authorized by the manufacturer. Confi rm the password using the set key and the key
the technician authorized by the manufacturer. Confi rm the password using the set key and the key
the technician authorized by the manufacturer. Confi rm the password using the set key and the key
the technician authorized by the manufacturer. Confi rm the password using the set key and the key
the technician authorized by the manufacturer. Confi rm the password using the set key and the key
power go to menu 3 "hydraulic scheme". Confi rm with the SET key and use the
the required hydraulic scheme number.
For end user:
It is possible to change the thermostove operating principle according to the season by choosing between
summer and winter. To select the season press SET, the season selection will appear on the display. Then press
the set key again and select the season with keys 1 and 2. Once selected, press the ON / OFF key to exit.
The choice of season changes the thermostove operation, see next chapter.
Following the principles of operation of the various hydraulic diagrams.
Important considerations:
•
healthcare will always have priority
•
There are three types of stand-by:
Type 01: the ambient temperature detected by the probe on the board has reached the SET AIR set
Type 02: the water temperature in the thermostove has reached the SET H2O set
Type 03: the external thermostat has detected that the desired temperature has been reached and
therefore the contact is open.
In this specifi c case the thermostove behaves as follows:
If the thermostat carries voltage to the card causing faults, the warranty will expire.
To confi gure the thermostat, simply remove the jumper on the THERM terminal (see the tab on page 16) and
connect our room thermostat, OPERATION BY A SPECIALIZED TECHNICIAN.
How to select the type of Stand-by (OPERATION BY A SPECIALIZED TECHNICIAN):
How to select the type of Stand-by (OPERATION BY A SPECIALIZED TECHNICIAN):
How to select the type of Stand-by (OPERATION BY A SPECIALIZED TECHNICIAN):
How to select the type of Stand-by (OPERATION BY A SPECIALIZED TECHNICIAN):
Press the SET button; press button
and confi rm it by pressing the SET key again. Press the
The display will show the different stand-by modes mentioned above, choose the mode using the
The display will show the different stand-by modes mentioned above, choose the mode using the
The display will show the different stand-by modes mentioned above, choose the mode using the
The display will show the different stand-by modes mentioned above, choose the mode using the
keys.
NOTE: The hydraulic scheme 00 is set by default, the WINTER season with stand-by mode 02.
When the thermostove is switched off manually or by programming, automatic ignitions exit from a stand-by
state will not be possible.
How to enable or disable the stand-by mode:
How to enable or disable the stand-by mode:
How to enable or disable the stand-by mode:
How to enable or disable the stand-by mode:
Press the SET button. With the
whether to enable (ON) or disable (OFF) the thermostove stand-by function.
whether to enable (ON) or disable (OFF) the thermostove stand-by function.
Press the ON / OFF button to exit
How to adjust the speed of the room fan (WHEN PRESENT):
How to adjust the speed of the room fan (WHEN PRESENT):
How to adjust the speed of the room fan (WHEN PRESENT):
How to adjust the speed of the room fan (WHEN PRESENT):
To adjust the fan speed, keep the button
adjust the room temperature, see point B instructions, scheme 00 on the following pages.
Let's see specifi cally the behavior of the thermostove according to the hydraulic scheme, the
presence and the stand-by mode and the chosen season
14
to go to menu 09. Press the SET button again. Enter the access key
to go to menu 09. Press the SET button again. Enter the access key
to go to menu 09. Press the SET button again. Enter the access key
to go to menu 09. Press the SET button again. Enter the access key
., key, go to menu 05 and confi rm with the SET key. Use key
pressed and adjust the desired speed with the same button. To
scroll to the "Technical settings" menu
key to go to menu 9-5.
of the
and
keys to select
and
sto select
Hide quick links:
Advertisement
Table of Contents
