Subscribe to Our Youtube Channel
Related Manuals for Antari PM-1
Summary of Contents for Antari PM-1
- Page 1 MANUAL ENGLISH Antari PM-1 Pan Motor for S-500 Ordercode: 80378P Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
Output Nozzle Pan Control ............................8 Setup and Operation ................................ 9 Control Modes ................................9 One PM-1 device (Stand-alone) ..........................9 Multiple PM-1 devices (Master/Slave control) ..................... 9 Multiple PM-1 devices (DMX Control) ........................10 Fixture Linking ................................11 Data Cabling ................................11 Control Panel ................................12... -
Page 3: Warning
Antari PM-1 Pan Motor for S-500 Warning Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. -
Page 4: Operating Determinations
For replacement use fuses of same type and rating only. ● The user is responsible for correct positioning and operating of the PM-1. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device. -
Page 5: Rigging
The PM-1 can be placed on a flat stage floor or mounted to any kind of truss with a clamp. Improper installation can cause serious injuries and/or damage of property! Antari excludes liability for unsafe situations, accidents and damage that are the result of: ●... -
Page 6: Return Procedure
Antari PM-1 Pan Motor for S-500 Connection with the mains Connect the device to the mains with the power-plug. Always pay attention, that the right color cable is connected to the right place. International EU Cable UK Cable US Cable... -
Page 7: Description Of The Device
Description of the device Features The PM-1 is an optional pan motor which can be used in combination with the Antari S-500 snow machine and allows you to control its pan movement. The PM-1 helps you increase the coverage of this already powerful machine. -
Page 8: Back
06) IEC power connector IN + Fuse T1AL/250V Installation Remove all packing materials from the PM-1 Pan Motor for S-500. Check if all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly. -
Page 9: Output Nozzle Pan Control
You can install the output nozzle of the S-500 Snow Machine on the Antari PM-1. Follow the instructions below. 01) Put the output nozzle of the S-500 Snow Machine in the installation bracket (01) of the PM-1 (Fig. 03). Fig. 03 02) Insert and tighten the mounting screws (Fig. -
Page 10: Setup And Operation
03) Plug the end of the electric mains power cord into a proper electric power supply socket. 04) When the PM-1 is not connected with a DMX cable, it functions as a stand-alone device. 05) See 3. Pan Mode on page 15 for more information about stand-alone mode. -
Page 11: Multiple Pm-1 Devices (Dmx Control)
02) Always use a safety cable (ordercode 70140/70141). 03) Use a 3-pin XLR cable to connect the PM-1 and other devices. 04) Link the units as shown in Fig. 06. Connect the first unit's DMX "out" socket with the second unit's "in"... -
Page 12: Fixture Linking
Antari PM-1 Pan Motor for S-500 Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. -
Page 13: Control Panel
When using multiple PM-1 fixtures, make sure that you set the DMX addresses right. Therefore, the DMX address of the first PM-1 should be 1(001); the DMX address of the second PM-1 should be 1+2=3 (003); the DMX address of the third PM-1 should be 3+2=5 (005), etc. -
Page 14: Menu Overview
Antari PM-1 Pan Motor for S-500 Menu Overview Ordercode: 80378P... -
Page 15: Main Menu Options
Antari PM-1 Pan Motor for S-500 Main Menu Options The main menu has the following options: 1. DMX address 8. Display options 2. DMX channel mode 9. Display orientation 3. Pan mode 10. Test mode 4. Pan speed 11. Total operation time 5. -
Page 16: Pan Mode
Antari PM-1 Pan Motor for S-500 3. Pan Mode In this menu you can set the pan range and run the auto program. 01) Press the MENU button until the display shows 02) Press the ENTER button to open the menu. -
Page 17: Dmx Error
Antari PM-1 Pan Motor for S-500 6. DMX Error In this menu you can determine the device’s behavior in case of a DMX signal error. 01) Press the MENU button until the display shows 02) Press the ENTER button to open the menu. -
Page 18: Display Orientation
Antari PM-1 Pan Motor for S-500 9. Display Orientation In this menu you can select the orientation of the display. 01) Press the MENU button until the display shows 02) Repeatedly press the ENTER button to choose one of the 2 display orientations:... -
Page 19: Dmx Channels
Antari PM-1 Pan Motor for S-500 DMX Channels 1 channel Channel 1 – Horizontal movement (Pan) Move the slider up, in order to move head horizontally (PAN). Gradual head adjustment from one end of the slider to the other (0–255, 127-center). -
Page 20: Maintenance
03) If all of the above appears to be O.K., plug the unit in again. 04) If you are unable to determine the cause of the problem, do not open the PM-1, as this may damage the unit and the warranty will become void. -
Page 21: No Response To Dmx
Antari PM-1 Pan Motor for S-500 No Response to DMX Suspect the DMX cable or connectors, a controller malfunction, a device’s DMX card malfunction. 01) Check the DMX setting. Make sure that DMX addresses are correct. 02) Check the DMX cable: Unplug the device; change the DMX cable; then reconnect to electrical power. -
Page 22: Product Specifications
Antari PM-1 Pan Motor for S-500 Product Specifications Model: Antari PM-1 Pan Motor for S-500 Input voltage: 100–240 V AC, 50/60 Hz Power consumption: 12 W DMX linking: 30 pcs Fuse: T1AL/250 V Dimensions: 170 x 152 x 153 mm (LxWxH) - Page 23 Antari PM-1 Pan Motor for S-500 Ordercode: 80378P...
- Page 24 ©2020 Antari...
Need help?
Do you have a question about the PM-1 and is the answer not in the manual?
Questions and answers