Maintenance - Milwaukee Heavy Duty M18 HCCT User Manual

WORKING INSTRUCTIONS FOR CUTTING
Set-up of the working area
Before work begins, the cables or cords must be
disconnected and it must be ensured that they remain
isolated from the power supply for the duration of the
work.
If it cannot be ensured beyond doubt that the cable or
insulated line has been disconnected, no work may be
carried out.
It is crucial that local safety provisions and the regulations
are observed.
Cable and cord may not be exposed to any mechanical
forces and must be secured from any uncontrolled
movements following the cut.
Do not expose tools to rain. Do not use tools in damp or
wet locations.
Preparation of cable cutter and battery
Before every use:
Inspect cable cutter for external defects.
Check the cutting tool for cracks and other signs
of wear.
Only use in perfect condition!
Before the cutting process begins, the battery capacity
must be checked: minimum 33% (see illustrated
description). It may require charging before work
commences.
Preparation for the cutting process
Support and x the cable or rope to be cut to minimise
the risk of uncontrolled movement.
Overhead cables and cords, in particular, can move
out of control and cause injury and/or damage.
The cutting head must be positioned at an angle of
90° to the cable or cord, so that the cable can lie in the
opened cutting jaws without tension and undesirable
shearing forces can be avoided.
WARNING! To reduce the risk of explosions,
electric shock, and damage to property and
equipment, never cut live electrical cables.
Device is NOT insulated. Contact with a live circuit
could result in severe injury or death. Turn off
power before making a cut. Never cut gas or water
lines. Keep hands away from all cutting edges
and moving parts. Laceration and amputation can
occur.
Always remove battery pack before changing
or removing accessories. Only use accessories
specifi cally recommended for this device. Others
may be hazardous.
To reduce the risk of injury, wear safety goggles or
glasses with side shields.
WARNING! To reduce the risk of injury, only
cut recommended materials for the blades (see
"Specifications"). Do not attempt to cut other
materials.
20 English
Cutting
Before cutting, ensure cutting blades are properly
installed.
1. Guide the cable at right angles to the cutting of the
cable cutter. Do not attempt to make angled cuts
as it will damage the device and cutting blades.
2. Pull and hold the trigger through the operation.
An LED will light when the trigger is pulled.
When the cut is complete or the device shuts off, the
cutting jaws open independently. If you release the
trigger during the cutting operation, you must press the
hydraulic reset button to open the cutting jaws.
NOTE: Workpiece may move slightly during the cut.
Action in the event of faults
The cable can be broached and become live, in
which case always inform the safety officer, stop
the cutting process, and initiate suitable protective
measures.
Always ensure that the device is and will stay
disconnected from the power supply before
approaching and touching the device.
Press and hold the hydraulic reset button until the
cutter opens completely.
Check the battery capacity.
Check the material and material thickness against
the technical data.
If it is suspected that a live cable has been cut, the
cable-cutter has to be inspected in an authorised
specialist workshop.
Jammed blades
Dirt and debris can cause the blades to become
jammed together after a cut.
Press and hold the hydraulic release button to
ensure the product has reset.
Remove the battery pack.
Follow the picture description to open the cutting
bars.
Clean any dirt and debris from the blades before
starting another cut.
Cutting tips
Do not attempt to make angled cuts as it will
damage the product and cutting blades.
Cut clean material to extend the cutting blade life.
Wipe dirt and debris from material and cutting
blades before beginning the cut.

MAINTENANCE

Remove the battery pack before starting any adjustment,
cleaning, and maintenance work on the product.
Never open the device, removable battery, or charger.
Check the product for any problems such as noise or
jamming of moving parts that could be affecting the
product.
Check the product, jaws, and crimping dies and cutting
blades for cracks and other signs of wear before each
use.
20