Table of Contents
Advertisement
WIRE LENGTH TABLE
Wa�s
10 AWG
12 AWG
VDC
(W)
(5.6mm
2
)
(3.3mm
17
897'
25
567'
24
40
309'
80
130'
100
84'
WIRING DIAGRAM
12 -28VDC IN
Ext in +
Ext in -
DMX in +
DMX in -
DMX in shield
LedSync thru +
LedSync thru -
LedSync shield
12V - 28V DC IN
To connect the driver to a DC power supply unit (PSU), connect the PSU's positive voltage supply wire to the VDC+ connector and the PSU's negative
voltage supply wire to the VDC- connector.
EXT in
You have the possibility to connect an external control device (0-10V control device, 10kΩ potentiometer or show selection switch) to the driver's Ext in+
and Ext in - connector. Configure the driver for use with an external control device over the 3 - button user interface.
DMX in/LedSync out
Use these connectors when the driver is used in a DMX network. For DMX in, connect the network cable's DMX+, DMX- and DMX shielding wire (the
orange/white, orange and brown wire in a CAT5 cable) to the DMX in+, DMX in- and DMX in shield connector respectively. For LedSync out, connect the
network cable's DMX+, DMX- and DMX shielding wire to the LedSync out+, LedSync out- and LedSync shield connector respectively. DMX Shield must be
grounded to Earth Ground at a single point external to power supply
LED groups
Indicates the location of the connectors for your LED groups. R(ed) represents channel 1, G(reen) represents channel 2, B(lue) represents channel 3 and
W(hite) represents channel 4. The default group color allocation can be changed over the 3-button user interface.
© 2020, Q-Tran Inc. 155 Hill St. Milford, CT 06460. All rights reserved - 203-367-8777 - sales@q-tran.com - www.q-tran.com
QTM-eLED+DMX
SPECIFICATIONS
VOLTAGE DROP CHART
14 AWG
16 AWG
18 AWG
2
)
(2.0mm
2
)
(1.3mm
2
)
(0.78mm
2
)
564'
355'
223'
140'
356'
224'
141'
88'
194'
122'
77'
48'
82'
51'
32'
20'
53'
33'
21'
13'
VDC and LED connectors:
AWG 24-16
1
0.2-1.5 mm
-
+
2
0.35 inch
Max | Vdc+
32V | Vdc-
DMX in +
DMX in -
12-28V / 6A Direct voltage controlled LED driver
DMX in shield
LedSync thru +
LedSync thru -
LedSync shield
20 AWG
22 AWG
24 AWG
26 AWG
(0.50mm
2
)
(0.33mm
2
)
(0.20mm
2
)
(0.13mm
88'
55'
35'
56'
35'
22'
30'
19'
12'
13'
8'
5'
8'
5'
3'
Other connectors:
AWG 20-16
0.5-1.5 mm
2
0.35 inch
TC
LED supply +
LINEARdrive 180D
Group
1
Group
2
Group
3
Group
4
2
)
22'
*Distances are based on a 5% Voltage drop max.
14'
● This product must be installed in accordance with the
7'
applicable installation code by a person familiar with
3'
the construction and operation of the product and the
hazards involved.
2
R
R
G
B
W
R
R
R
2
Advertisement
Table of Contents
