Olympus OmniScan MX2 Getting Started Manual
  1. Manuals
  2. Brands
  3. Olympus Manuals
  4. Security Sensors
  5. OmniScan MX2
  6. Getting started manual

Olympus OmniScan MX2 Getting Started Manual

Hide thumbs Also See for OmniScan MX2:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
OmniScan MX2
Getting Started Guide
Intended Use
The OmniScan MX2 is designed to perform nondestructive inspections of industrial and commercial
materials. Do not use the OmniScan MX2 for any purpose other than its intended use.
Instruction Manual
Before use, thoroughly review the OmniScan MX and MX2 User's Manual and the OmniScan MXU
Software User's Manual, and use the product as instructed. The user's manuals contain essential
information on how to use this Olympus product safely and effectively. Keep this guide and the user's
manuals in a safe and accessible location. The PDF versions of the OmniScan MX2 User's Manual and
OmniScan MXU Software User's Manual are also available on the documentation USB drive that is
shipped with the OmniScan MX2, or can be downloaded at www.olympus-ims.com.
Safety Signal Words
Indicates an imminently hazardous situation calling attention to a procedure, practice, or the like,
which, if not correctly performed or adhered to, could result in death or serious personal injury
Indicates a potentially hazardous situation calling attention to a procedure, practice, or the like, which,
if not correctly performed or adhered to, could result in death or serious personal injury.
Indicates a potentially hazardous situation calling attention to a procedure, practice, or the like, which,
if not correctly performed or adhered to, could result in minor or moderate personal injury, material
damage, particularly to the product, destruction of part or all of the product, or loss of data.
OmniScan MX2 — Getting Started Guide
1

Advertisement

Table of Contents
loading

Related Manuals for Olympus OmniScan MX2

Summary of Contents for Olympus OmniScan MX2

  • Page 1 Olympus product safely and effectively. Keep this guide and the user’s manuals in a safe and accessible location. The PDF versions of the OmniScan MX2 User’s Manual and OmniScan MXU Software User’s Manual are also available on the documentation USB drive that is shipped with the OmniScan MX2, or can be downloaded at www.olympus-ims.com.
  • Page 2 340 V can be present on the inner conductor of the UT connectors, and up to 115 V can be present on the PA connector. The warning symbol near the PA and UT connectors signals this electric shock risk. OmniScan MX2 — Getting Started Guide...

  • Page 3: Warnings On Battery Use

    • Do not expose a battery to moisture or rain; doing so could cause an electric shock. • Only use the OmniScan MX2 or an external charger approved by Olympus to charge the battery. • Do not recharge a battery unless the indicators light up when the capacity check button on the battery is pressed.

  • Page 4: Charging The Batteries

    Figure 1 Battery replacement The OmniScan MX2 can operate using only one battery, making it possible to remove the other battery while the unit is in operation (hot swap). When two batteries are used, the OmniScan MX2 automatically discharges both batteries at the same time, increasing the remaining operating time by about 10 %.
  • Page 5 If you attempt to start up the OmniScan MX2 using batteries with a charge too low for operation, the power indicator light rapidly flashes red for approximately three seconds. To operate the OmniScan MX2, replace the batteries or plug in the DC power adaptor.

  • Page 6: Front Panel

    Front Panel The front panel of the OmniScan MX2 contains all the main controls and indicators. This panel is divided into seven areas: the touch-screen display, the main control area, the function keys, the power button, the increment keys, the Help key, and the indicator lights.

  • Page 7: Turning On And Off The Omniscan Mx2

    A message asking you if you want to save your setup appears. To save your setup, select Yes. You can also turn off the OmniScan MX2 by pressing and holding the Power key for ten seconds. However, your setup will NOT be saved.
  • Page 8 Adaptors The figure below shows how the OmniScan MX2 can be integrated with your existing equipment. DE15 to LEMO encoder cable adaptor Scanner with DE15 encoder (U8775201) cable Scanner with LEMO encoder To scanner interface cable Adaptors Phased array extension...

Table of Contents