Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bosch FLEXIDOME multi 7000i
Summary of Contents for Bosch FLEXIDOME multi 7000i
- Page 1 FLEXIDOME multi 7000i NDM‑7702‑A | NDM‑7703‑A Installation manual...
-
Page 3: Table Of Contents
FLEXIDOME multi 7000i Table of contents | en Table of contents Safety Safety message explanation Safety precautions Important safety instructions Notices Short information System overview Product description Intended use Using the camera Operation with external systems Planning information Unpacking Parts included... - Page 4 | Table of contents FLEXIDOME multi 7000i Transfer Disposal Technical data 10.1 Dimensions 10.2 Specifications 2021-03 | 01 | Bosch Security Systems B.V. Installation manual...
-
Page 5: Safety
FLEXIDOME multi 7000i Safety | en Safety Read, follow, and retain for future reference all of the following safety instructions. Follow all warnings before operating the device. Safety message explanation In this manual, the following symbols and notations are used to draw attention to special... -
Page 6: Notices
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. FCC suppliers Declaration of Conformity FLEXIDOME multi 7000i: NDM-7702-A, NDM-7703-A Responsible party Bosch Security Systems Inc 130 Perinton Parkway 14450 Fairport, NY, USA www.boschsecurity.us... -
Page 7: Short Information
Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults, incompleteness or discrepancies between this manual and the product described. Copyright This manual is the intellectual property of Bosch Security Systems and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly. -
Page 8: System Overview
System overview Product description The FLEXIDOME multi 7000i camera is built for high-quality performance, featuring four independent imagers with motorized zoom/focus lenses. It helps to simplify installation and lower costs while maintaining flexibility in coverage. With four scenes simultaneously in a single camera, it is perfect for wide area coverage, traffic intersections and building corners. -
Page 9: Intended Use
Integration with the many Bosch recording solutions is seamless. Operation with external systems The web browser is the most direct way of using the camera, however, the Bosch download store provides several other free applications (listed below) for viewing and controlling the camera. -
Page 10: Planning Information
This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Verify that all parts are included. If any items are missing, notify your Bosch Security Systems sales or customer service representative. -
Page 11: Preparation
Screwdriver and bit holder for TR20 bit, or use the provided TR20 Allen key. – Standard micro SD card (optional) Note: Bosch recommends the use of industrial micro SD cards with health monitoring. – Wireless USB dongle for wireless commissioning (optional) - available mid of 2021. -
Page 12: Installation
| Installation FLEXIDOME multi 7000i Installation Installing the mounting plate The mounting plate is used to fix the camera to a flat surface. It offers different holes and slots for a variety of fixing options. 1 PIP Mounting holes for installation with Mounting holes for 4 in. -
Page 13: Installing The Mounting Plate Without Conduit
FLEXIDOME multi 7000i Installation | en Notice! The plugs and screws for surface mounting are not supplied with the camera. 5.1.1 Installing the mounting plate without conduit Remove the mounting plate from the box. Position the mounting plate with the center hole on top of the cable exit on the surface, and mark the positions of the screw holes on the surface. - Page 14 | Installation FLEXIDOME multi 7000i Attach the conduit plate with the conduit plate adapter to the surface with a 5-6 mm (0.2 in.) screw. Remove the mounting plate from the box. Mark the positions of the holes on the surface. The mounting plate has only one side available for the conduit.
-
Page 15: Installing The Camera Base
Local storage Notice! Bosch recommends the use of industrial micro SD cards with health monitoring. If necessary, install a micro SD card in the micro SD slot. Press the micro SD card firmly until it latches into place in the slot. -
Page 16: Installation Steps
| Installation FLEXIDOME multi 7000i Grounding Warning! Trained electricians only! Work at electric appliances must only be carried out by qualified technicians. To ground the camera: Remove the screw from the bottom of the camera base. Install the ring terminal (not supplied with the camera) on the screw. - Page 17 FLEXIDOME multi 7000i Installation | en Put the RJ-45 punch-through aid on the network cable. Remove the tubes from the M20 rubber grommets. Put one M20 rubber grommet on the edge of the RJ-45 punch-through aid. Pull the RJ-45 punch-through aid together with the network cable connector through the M20 rubber grommet.
- Page 18 | Installation FLEXIDOME multi 7000i Put the network cable through the network cable inlet. 10. Put the auxiliary connections cable through the other cable inlet. 11. Fix the M20 rubber grommets in both cable inlets to make sure that the cable inlets are firmly closed.
- Page 19 FLEXIDOME multi 7000i Installation | en 13. Position the camera base on the mounting plate, so that the screw holes of camera base and mounting plate match. Slightly press the camera base onto the mounting plate until you hear/feel a click. Make sure that the camera base is secured.
-
Page 20: Wiring The Camera Base
| Installation FLEXIDOME multi 7000i TR20 5.2.3 Wiring the camera base Network connection Connect the network cable to the network connector. Auxiliary connections - power connection Notice! IP66 water/dust protection For IP66 water/dust protection, use cables with a diameter of at least 5 mm. - Page 21 FLEXIDOME multi 7000i Installation | en Notice! If PoE+ is not available, use a 24V AC power supply. Remove 8 mm (0.3 in.) of the power wires insulation. Connect the power wires to the 2-pin power connector. Connect the 2-pin power connector to the power connector of the camera base.
-
Page 22: Connecting A Wireless Usb Dongle
The camera is equipped with a USB-C port for a wireless USB dongle (sold separately, available mid of 2021), so that you can easily perform the initial configuration wirelessly. Using a mobile device with the Bosch Project Assistant app, you can do initial set-up and lens zoom- focus to find the right scene. -
Page 23: Panning Each Of The Four Lenses Over The Ring
FLEXIDOME multi 7000i Installation | en 5.3.1 Panning each of the four lenses over the ring Pan each of the four lenses to set the position that you need. You can pan 0° to 360° over the integrated transportation ring in the camera. -
Page 24: Rotating Each Of The Four Lenses
| Installation FLEXIDOME multi 7000i To set each of the four lenses at 0° tilting, which means that the lens captures an image at 90° to the mounted surface, make sure that the white dot in the middle of the larger lens holder meets the edge of the smaller lens holder. -
Page 25: Rolling Each Of The Four Lenses
FLEXIDOME multi 7000i Installation | en To set the camera in an optimal 360º overview position, rotate each of the four lenses so that the white triangle icons match. 5.3.4 Rolling each of the four lenses Roll each of the four lenses to set the position that you need. You can roll -90º to 90º. -
Page 26: Optional Mounting Accessories
| Installation FLEXIDOME multi 7000i TR20 Remove the protective cover from the bubble. Optional mounting accessories NDA-7051-PIPW Pendant interface plate. NDA-7051-CA Conduit adapter M25 (5 pieces). NDA-U-WMT Universal wall mount for dome cameras, white. 2021-03 | 01 | Bosch Security Systems B.V. - Page 27 FLEXIDOME multi 7000i Installation | en NDA-U-PMT Universal pipe mount for dome cameras, 31 cm, white. NDA-U-PMTE Extension for universal pipe mount, 50 cm, white. NDA-U-PMTS Universal pendant pipe mount for dome cameras, 11 cm (4"), white. NDA-U-PSMB Surface mount box (SMB) for wall mount or pipe mount.
- Page 28 | Installation FLEXIDOME multi 7000i NDA-U-PA0 Surveillance cabinet, 24 VAC input, 24 VAC output, IP66. NDA-U-PA1 Surveillance cabinet, 100 - 120 VAC 50/60 Hz input, 24 VAC output, IP66. NDA-U-PA2 Surveillance cabinet, 230 VAC input, 24 VAC output, IP66. NDA-U-WMP Back plate for universal wall mount, corner mount and pole mount, white, IP66.
- Page 29 FLEXIDOME multi 7000i Installation | en SFP-25 SFP Fiber Optic Module, 2 km (1.2 miles), 1 SC connector. Multi-mode. 1310/1550 nm. SFP-26 SFP Fiber Optic Module, 2 km (1.2 miles), 1 SC connector. Multi-mode. 1550/1310 nm. NDA-U-PMTG Universal pipe mount, compatible with gang box installation for fixed dome cameras only, white.
-
Page 30: Configuration
FLEXIDOME multi 7000i Configuration Bosch Project Assistant If you have connected a wireless USB dongle, you can use the Bosch Project Assistant app on a mobile device (iOS, Windows, or Android) to perform the initial configuration wirelessly. Download the Project Assistant app. -
Page 31: Video Security Client
Video Security Client The Video Security Client is a free, easy-to-use video-surveillance application provided by Bosch for local and remote monitoring of IP cameras and appliances. The software supports up to 16 cameras. The Video Security Client has extensive dewarping capabilities and can be used for client-side dewarping as well as for viewing the available modes. -
Page 32: Troubleshooting
| Troubleshooting FLEXIDOME multi 7000i Troubleshooting Resolving problems The following table is intended to help identify the causes of malfunctions and correct them where possible. Malfunction Possible causes Solution Unit does not operate. Power failure. Check power supply. Check if PoE+ or 24 V auxiliary input is... -
Page 33: Customer Service
FLEXIDOME multi 7000i Troubleshooting | en – The device is not properly connected to the network. Check the cable connections in this case. – The device is not correctly integrated into the network. Check the IP address, subnet mask, and gateway address. -
Page 34: Maintenance
Dry the bubble thoroughly with a dry nonabrasive cloth to prevent water spots. Never scrub the bubble with any abrasive material or cleaners. Bosch recommends cleaning the exterior of the bubble with NOVUS “No. 1” Plastic Clean & Shine (or equivalent), according to manufacturer’s instructions. Refer to www.novuspolish.com... - Page 35 FLEXIDOME multi 7000i Maintenance | en Re-attach the camera dome cover onto the camera base. Bosch Security Systems B.V. 2021-03 | 01 | Installation manual...
-
Page 36: Decommissioning
| Decommissioning FLEXIDOME multi 7000i Decommissioning Transfer The device should only be passed on together with this Installation manual. Disposal Old electrical and electronic equipment This product and/or battery must be disposed of separately from household waste. Dispose such equipment according to local laws and regulations, to allow their reuse and/or recycling. - Page 37 FLEXIDOME multi 7000i Technical data | en Technical data 10.1 Dimensions 175.3 (6.9) Dimensions in mm (in.) 10.2 Specifications Power Input voltage 30 W (according to PoE+ IEEE 802.3at Type 2, Class 4) 24 VAC ±10% PoE+ and auxiliary power can be connected simultaneously...
- Page 38 | Technical data FLEXIDOME multi 7000i Dynamic range HDR Measured according to 105 dB WDR IEC 62676 Part 5 Optical Lens 3.7 - 7.7 mm F1.9 Adjustment Motorized zoom/focus Day/Night Switchable IR-cut filter Viewing angle (12 MP variant) Wide: 81.9º x 59.8º (H x V) Tele: 39.5º x 28.9º (H x V) Viewing angle (20 MP variant) Wide: 85.6º...
- Page 39 FLEXIDOME multi 7000i Technical data | en Video functions White Balance 2300 to 10000K, 3 automatic modes (Basic, Standard, Sodium vapor), Manual mode and Hold mode Shutter Automatic Electronic Shutter (AES); Fixed shutter (1/25[30] to 1/15000) selectable; Default shutter Day/Night...
- Page 40 | Technical data FLEXIDOME multi 7000i Input/output Audio line out 1.0 Vrms, 10 kOhm Microphone 1 integrated microphone (can be disabled) Alarm input 1 input Alarm input activation Short or DC 5V activation Alarm output 1 output Alarm output voltage 30 VDC, max.
- Page 41 Troubleshooting – Repair & Exchange – Product Security Bosch Building Technologies Academy Visit the Bosch Building Technologies Academy website and have access to training courses, video tutorials and documents: www.boschsecurity.com/xc/en/support/training/ Bosch Security Systems B.V. 2021-03 | 01 | Installation manual...
- Page 42 | Technical data FLEXIDOME multi 7000i 2021-03 | 01 | Bosch Security Systems B.V. Installation manual...
- Page 44 Bosch Security Systems B.V. Torenallee 49 5617 BA Eindhoven Netherlands www.boschsecurity.com © Bosch Security Systems B.V., 2021 202103170945...