Download Print this page

Advertisement

Quick Links

Catalogue
Catalogue---------------------------------------------------------------------1
Warning-------------------------------------------------------------------- 1
Assembling steps -----------------------------------------------------2-14
Exploded view ---------------------------------------------------------- 15
Parts list --------------------------------------------------------------16-17
Daily Maintenance------------------------------------------------------------------18
Warning
1. Before exercise, please check to make sure all bolts are tightened and handlebar welds are intact.
2. Wear appropriate footwear during work out. Do not flip the handlebars during exercise.
3. When weight stack, suspender or other parts are caught, ask another person's help to avoid the
sudden drop of weight stack.
4. Do not distort the cable when you adjust its length (tightness). After using for a period of time, you
should check if cable skin has worn out or the cable is badly stretched, contact the serviceman to
repair or replace as soon as you find problems.
5. Do not drop weight stacks all of a sudden to avoid damage and injury. You should always lower the
weight stacks slowly.
6. Do not insert hand and other parts of the body between/under weight stacks and other moving parts
to avoid injury.
7. Children under 16 should exercise under adult's guidance.
8. People have special conditions (for example, aged or diseased) should always consult your physician
before starting exercise.
1

Advertisement

loading

Summary of Contents for Orbit MAX 2B

  • Page 1 Catalogue Catalogue---------------------------------------------------------------------1 Warning-------------------------------------------------------------------- 1 Assembling steps -----------------------------------------------------2-14 Exploded view ---------------------------------------------------------- 15 Parts list --------------------------------------------------------------16-17 Daily Maintenance------------------------------------------------------------------18 Warning 1. Before exercise, please check to make sure all bolts are tightened and handlebar welds are intact. 2. Wear appropriate footwear during work out. Do not flip the handlebars during exercise. 3.
  • Page 2: Assembling Steps

    Assembling steps 1. Remove all parts out of boxes and place around area of installation! Place bolt packs in front of the area where you want the gym. 2. Place part (2) in desired position, then connect part (3) with part (4) using bolts (M10x75mm)(13), washers (26) and locknuts (23).
  • Page 3 Connect backrest tube (5) to seat tube (3) with bolts (M10x75mm)(13) , washers (26) and locknuts (23). Connect tube (1) to backrest tube (5) and vertical tube (4) with (M10x75mm)(13) , washers (26) and locknuts (23).
  • Page 4 4. Insert leaders (10) into the oriented holes on the bottom of the curl base tube (2), in turn, slide cover bumpers (51), rubber weight stack (48) and plastic top plate (46). Mount leader top tube(6) to the leader (10) by washers (26) and bolts (M10x20mm)(5). Connect exercise chart flip (76), leader top tube (6) and Lab pull down top tube (1) with bolts (M10x75mm)(13), washers (26) and locknuts (23).
  • Page 5 5. Connect backrest tube (5) and chest-extension rotating frame (7) through the rotating bearing (25), tighten with Allen bolt (30). Secure bearing bases (38), washers (26) and bolts (M10x25mm)(6). Connect the chest-extension frame (19), backrest tube (5) and pulley fixing frame (26) with bolts (M10x75mm)(12), washers (26) and locknuts (23).
  • Page 6 7. Attach oriented hook (13) and steel spacer (34) to seat tube (3) with bolt (M10x90mm)(15), washer (26), washers (31) and locknut (23). Attach rubber cushion (56) to the back of leg-kicking frame (39). Connect seat tube (3) and leg-kicking frame (39) with bearings (70), bolt (M10x80mm)(14), washers (27) and locknut (24).
  • Page 7 8.Attach chest-extension handlebars (8R&L) to the chest-extension rotating frame (7), which was already attached to backrest tube (5) in step 4, with washers (26) and bolt (M10x30mm)(7). Slide crossed bearing covers (29) to the chest-extension handlebars (8R&L), tighten with nut canopy (58). Connect pulling bar (27R&L) and crossed bearing cover (29) through limiting bushing (31), bolt (M12x120mm)(19), washer (27) and locknut (24).
  • Page 8 . Attach handlebar tube (11) to the parallel bar with washer (25) and bolt (M10x20mm)(5). Attach parallel par (20) to the vertical tube (4) with bolts (M10x75mm)(13), washers (26) and locknuts (23). Attach arm cushion (44) to the parallel bar (20) with washers (25) and bolts (M8x70mm)(8). Connect backrest cushion (41) and backrest adjusting tube (24) with washers (25) and bolts (M8x30mm)(2), then insert backrest adjusting tube (24) into backrest adjusting bushing (18), and lock it with pop pin (68).
  • Page 9 10. Attach shrouds (9) to the curl base tube (2) with washers (M8)(25) and bolts (M8x30mm)(3). Attach handlebar tube (11) to the vertical tube (4) with washer (M8)(25) and bolt (M10x20mm)(2).
  • Page 10 11. Attach backrest cushion (43) to the vertical tube (4) with washers (25) and bolts (M8x20mm)(2).
  • Page 11 12.Wire circling way: Cables to be installed in order cable (67) first, cable (63) second, cable (64) third, cable (66) fourth and cable (65) last. View following 5 pages for figure diagrams.
  • Page 12 The 1 wire: (refer to the following illustration)
  • Page 13 The 2 wire: (refer to the following illustration) The 3 wire: (refer to the following illustration)
  • Page 14 The 4 wire: (refer to the following illustration)
  • Page 15 The 5 wire: (refer to the following illustration)
  • Page 17: Exploded View

    EXPLODED VIEW...
  • Page 18 Parts List I...
  • Page 19: Parts List

    Parts List II...
  • Page 20 Parts List III...
  • Page 21 1 box of 4; box size: 1950*270*210mm PART NO. DESCRIPTION QTY. PART NO. DESCRIPTION QTY. Vertical tube Backrest adjusting tube Chest-extension adjusting Backrest tube tube Leader Leg-kicking adjusting tube Leader II Chest-extension arm Leader Shield Lab bar 2 box of 4; box size: 1280*860*210mm PART NO.
  • Page 22: Description Qty

    4 box of 4; box size: 620*280*280mm PART NO. DESCRIPTION QTY. PART NO. DESCRIPTION QTY. Seat cushion Sponge tube Double bar Backrest sofa Backrest cushion Leg-covering strip Arm cushion Daily Maintenance It is recommended that you maintain the equipment as the below chart: Maintain Every day Every week...